User manual

Operation : (while the system is in the operation mode)
#
(a) (b) (c)
a) Put the EM card close to the reader. One-beep confirms the reading and 30 seconds waiting time is given for the
entry of the Duress Code, the Amber LED keeps flashing
b) Key in one of the Duress Codes for the specific output (the Code programmed in “Location 41, 42, or 43” for
Output 1, 2 and 3 respectively)
c) Confirm it with the # key. The specific Output activates in a normal way and the Duress Output also activates to
report Duress Event to an alarm system.
NOTE: The Duress Event can not be reported if the operation mode is EM Card alone. It is required to key in the
Duress Code directly if necessary.
VISITOR CODES (FOR OUTPUT 1 ONLY) (Location 40)
The Visitor Codes are the temporary user codes for operating of the Output 1 (mainly for door strike in access control).
They can be programmed as “One Time Codes” or “Codes with Time Limit”. The Visitor Codes will be cleared
automatically after use if they are one time codes, or, when the allowed time expires.
VISITOR ID
50 Visitor IDs for storing the codes. They are represented by a
Two-digit ID Number of
01
to
50
.
0999
= Clear all the Visitor Codes from Location 40. Please
see the Programming example below for the details.
VALID PERIOD
The codes in this box MUST be two digits and they represent the time of the operation.
00
--- One Time Code
One Time Code has no time limit but it can only be used for ONCE.
It is cleared by the system automatically after use.
01
-
99
--- Time Limit in Hour(s)
The Visitor Code can be set with the valid time limit of 1 Hour to 99 Hours with a
two-digit number of 01 to 99. The visitor code is cleared by the system when
the time limit reaches.
VISITOR CODES
When a new Visitor Code is put in the same Code box, the old code is replaced.
The Visitor Codes can be 4-8 digits for the Manual Mode code entry.
The Visitor Codes MUST be in the same digit length with the Master Code for Auto Mode code entry.
The Visitor Codes can not reset Duress Output.
NOTE: All Visitor Codes will be cleared after power down to prevent extension/confusion of their valid time limit.
EXAMPLES:
Example 1: Set a “One Time Visitor Code” with the number of “1 2 6 8” for the Output 1
40 01 00 1268 #
(a) (b) (c) (d) (e)
(a) Visitor Code Programming, (b) The Visitor ID, (c) An One Time Code, (d) The Visitor Code, (e) Entry Confirmation
Example 2: Set a “Visitor Code” with the number of “1 3 7 8” that is valid for three hours for the Output 1
40 02 03 1378 #
(a) (b) (c) (d) (e)
(a) Visitor Code Programming, (b) The Visitor ID, (c) Valid for 3 Hours, (d) The Visitor Code, (e) Entry Confirmation
Read Card
Duress Code
4-8 DIGITS
40 #
01
-
50
00
or
01
-
99
VISITOR CODE VALIDATIONLOCATION VISITOR ID VALID PERIOD
30
15
RF REMOTE CONTROLLER -- (DA-2800 ONLY)
The DA-2800 RF Remote Controller consists of a built-in receiver and two remote control keys, which has 4 channels
to control the Output Relay 1, 2, 3 and the built-in door chime. Two remote keys are supplied and up to 40 remote
keys can be accommodated by the system. The receiver (decoder) of the system learns the ID codes from the remote
keys. Each remote key contains a 24-bit ID code that provides over 1 million code combinations. The remote key gives
around 60 Meters of controlling distance in open space to the receiver.
(A) Procedure of Recording An RF Remote Key -- (Learning)
The RF remote keys that prepare to work with the decoder are required to be registered. The decoder learns the ID of the
remote keys one by one beforehand with the following procedures:
1) Press and hold the LEARN button on the receiver unit for 1 second until the REMOTE LED turns ON. (The button is
inside the hole. Use a pin or the tip of a ball pen to reach it). See Figure 1
2) The decoder of the receiver is in Waiting Mode for 10 seconds waiting for the signal from the Remote Key after
the Remote LED turning ON.
3) Press any button of the RF Remote Key unit ONCE within the 10 seconds for the receiver to learn the ID Code from it.
4) The REMOTE LED on the receiver unit turns OFF after the ID Code is learned.
5) Take the above learning procedures 1-4 for other RF Remote Keys
(B) Procedure of Deleting The RF Remote Keys from Memory -- (Clearing)
If an RF remote key is lost it is necessary to delete it from the memory of the receiver. Every time the system will clear
all the ID Codes of the RF Remote Keys in the deletion. Re-learn the existing remote keys are necessary.
1) Press and hold the LEARN button on the receiver unit for 8 seconds (Remote LED turns ON) until the REMOTE
LED gives 2 flashes to confirm that all the data are erased. Then the LED turns OFF.
2) Record the ID Code of the existing RF Remote Keys (not lost) into the memory again one by one with the
procedures stated in the “Recording An RF Remote Key”
(C) Operating The System with RF Remote Control Keys -- (Operation)
The system can be operated with the RF Remote Control Keys no matter it is in Split-decoded Mode or in Standard
Alone Mode. In the Split-decoded mode, the RF Remote Key operates the system according to the functions and data
that have been programmed with the digital keypad. While in Stand Alone operation the system operates its outputs
according to the functions that stated in the Stand Alone Mode 1 or Mode 2.
1) Press button A to operate Output 1
2) Press button B to operate Output 2
3) Press button C to operate Output 3
4) Press button D to operate the built-in Door Chime
STAND ALONE MODE -- (DA-2800 ONLY)
The system that operates in Stand Alone mode does not require the keypad. It is directly controlled by the RF Remote
Key for the outputs. It is an ideal solution for the remote controls of door strike, alarm arm-disarm, garage door opening
etc.. The following settings are necessary while the system is in stand alone operation:
1) Put the “Function Mode Jumper” to position “2” or “3” for the desired Stand Alone Operation Mode. See the
“Function Mode Jumper Setting” stated above for the details.
2) Always put “Link-up Jumper” on OFF position.
3) Leave the “Data I/O” port open without any connection.
4) Make all the installation connections to the terminals of the decoder unit.
INDIVIDUAL