User manual

ManualsBrandsSYGONIX ManualsDoor & Window ProtectionCode lock type Surface-mount IP66 + separate verification unit

FEATURE PROGRAMMING & OPERATION INSTRUCTIONS

SET SYSTEM INTO PROGRAMMING MODE WITH THE MASTER CODE

IMPORTANT NOTE:

1) DO NOT TURN OFF POWER while the keypad is in Programming Mode. Otherwise, it may cause data lost/error to the

programmed features in the memory.

2) The keypad beeps after power up. Wait 1 minute until the end of the power up delay, then key in the Master Code for

setting the system into programming mode.

3) For the owner’s convenience in programming at the first time, the factory has put a Master Code 0 0 0 0 into the

keypad (It is NOT a default code). To compromise security, in all cases, the owner should program a new Personal

Master Code to invalidate the factory set Master Code after the keypad is owned.

4) The Button has two functions in the keypads with Door Bell button. It is a door bell button while the keypad is in

normal operation; and it is equivalent to a

Button in programming mode.

MASTER CODE

The Master Code can be a factory set master code or the private master code that

was set by the owner.

Validate the master code with

* *

(or ) .

2-beep confirms a valid master code. The Mains LED (Amber) is constantly ON after the system is set in the

programming mode.

DIRECT ACCESS TO PROGRAMMING MODE WITH THE “DAP” CODE – 8 0 8 0

Set System Into Programming Mode With DAP Code In Case Of The Master Code Is Forgotten ! !

The owner requires to apply the following procedures precisely to set the system into programming mode

with the DAP code 8 0 8 0.

1) Switch OFF all the power for 1 minute to ensure that the system is fully discharged.

2) Swich ON power again. The system is in Power-up Mode for 1 minute and the buzzer gives beeps during the whole

period. This is the only time limit for setting the system to Direct Access to Programming (DAP).

3) Press the Egress Button (EG IN) once first to enable the DAP function.

4) Key in the DAP Code 8 0 8 0 and validate it with

* *

(or ), the existing Master Code in the memory is

erased and the power up beep stops. The keypad turns itself into programming mode like using the Master Code and

it is ready to accept the new programming data.

5) If the Egress Button is not pressed and the DAP code is not keyed in within the power up period, the system will set

itself to normal operation mode. To set it back to power-up mode, repeat procedures 1-4.

DAP CODE

The DAP code is fixed on 8 0 8 0 and it is valid only in the Power-up Period after the Egress Button is pressed.

Validate the DAP code with the

* *

(or )

2-beep confirms the system is in the Programming Mode; and the Mains LED is constantly ON.

See “RECORD A MASTER CODE” at “Location 01” for the details of programming a new master code.

NOTE:

If the keypad is linking up with the DA-2800 controller in the Split-decoded operation, it is necessary to put the

controller’s “Link-up Jumper” to “ON” position to get the new Master Code for it. As the Master Code is also the link-up

code of the two units. Do Not Forget to put the Link-up jumper back to OFF position after the programming. Otherwise,

the controller will accept other keypads to link up with it.

0000

8080

MASTER CODE VALIDATION

DAP CODE VALIDATION

PROGRAMMING SUMMARY CHART

LOCATION

FUNCTION

ENTRY LIMITS & CODE

OPTIONS

CODE ENTRY

FACTORY

DEFAULT

0 1

Master Code 4-8 Digits

MASTER CODE

NIL

0 2

Super User PIN 4-8 Digits

SUPER USER PIN

NIL

0 3

Common User PIN for O/P 1

4-8 Digits

COMMON USER PIN 1

NIL

0 4

Common User PIN for O/P 2

COMMON USER PIN 2

NIL

0 5

Common User PIN for O/P 3

COMMON USER PIN 3

NIL

1 0

User PINs / Cards for O/P 1

CODE 1

MEDIA:

1---EM Card

2---Private User PIN

3---EM Card+Sec User PIN

4---EM Card+Com User PIN

5---Deletion of User PIN

CODE 2

USER ID:

000-999---Group 1(10)

001-100---Group 2(20)

001-100---Group 3(30)

CODE 3

USER PINs / Cards:

4-8 Digits / Cards

CODE1

CODE2

CODE3

NIL

2 0

User PINs / Cards for O/P 2

CODE1

CODE2

CODE3

NIL

3 0

User PINs / Cards for O/P 3

CODE1

CODE2

CODE3

NIL

4 0

Visitor Codes

CODE 1

VISITOR ID: 01-50

CODE 2

VALID PERIOD:

00---One Time

01-99 Hours

CODE 3

VISITOR CODE:

4-8 Digits

CODE1

CODE2

CODE3

NIL

4 1

Duress Code for O/P 1

CODE ID

O/P 1: 01-50

CODE ID

O/P 2: 01-10

CODE ID

O/P 3: 01-10

DURESS CODE: 4-8 Digits

CODE ID

DURESS CODE

NIL

4 2

Duress Code for O/P 2

CODE ID

DURESS CODE

NIL

4 3

Duress Code for O/P 3

CODE ID

DURESS CODE

NIL

5 1

O/P Mode for O/P 1

OUTPUT MODE & TIME:

0--- Start / Stop

1---99999 Seconds,

Momentary

O/P MODE & TIME

5 Seconds

5 2

O/P Mode for O/P 2

O/P MODE & TIME

5 Seconds

5 3

O/P Mode for O/P 3

O/P MODE & TIME

5 Seconds

6 0

Personal Safety & Lock-out

LOCK-OUT CODE:

1---10 Trial, Lock-out 60 Sec.

2---10 Trial, Activates Duress

5-10---5-10 Trial, Lock-Out 15

Minutes

00---No Lock-out

LOCK-OUT CODE

Code = 1,

10 Trials,

Lock-out 60

Seconds

7 0

PIN Entry Mode

ENTRY MODE:

1---Auto Mode

2---Manual Mode

ENTRY MODE

Mode = 2,

Manual Mode

7 1

Pacifier Tone ON-OFF

FUNCTION MODE:

0---OFF

1---ON

FUNCTION MODE

Mode = 1,

Pacifier Tone

7 2

Output Announcer

FUNCTION MODE

Mode = 1

Announcer ON

7 3

Standby LED Flashing

FUNCTION MODE

Mode = 1,

Flashing On

EGRESS BUTTON

PRESS ONCE