User manual

INTRODUCTION
The DA-2800 or DA-2801 is a self-contained access controller. It has been designed mainly as the decoder unit
working together with the keypads in the DK-2800 series to make up a split-decoded keypad system.
In split-decoded operation the system provides full Tri-Tech features of accepting EM Card, PIN/Code and RF Remote
Control. This unique design philosophy makes the system to provide high level of security in preventing sabotage far
ahead of the traditional stand alone keypad systems.
The DA-2800 also has been designed to work stand alone without keypad. The three relay outputs can be controlled
by the RF remote control key directly. The Output 1 operates in Start/Stop mode or in Momentary mode with the built-
in adjustable timer for door strike. The Output 2 and 3 operate in Start/Stop mode and manually controlled Momentary
mode respectively.
DA-2801 is the simplified version without the RF remote control function. It is solely a full feature decoder of the DK-
2800 series keypads in Split-decoded operation.
The DA-2800 or DA-2801 has three output relays and a built-in door chime. It is an ideal device for Door Strike, Alarm
Arm-disarm control and actuation of Automatic Operator, such as garage door opener.
The keypad system with the DA-2800 or DA-2801 decoder in Split-decoded operation offers full features performance
even the keypad is just a simplified version. Maximum three keypads can be connected in parallel to the decoder unit
with one of them setting in master mode and the other two setting in slave mode. Each keypad can be programmed
with its own PINs and Cards. The slave keypads take the features and the functions programmed in the master keypad
to operate the system. The decoder interprets the data and operates the desired functions faithfully.
FEATURES
DA-2800 – Full Feature Decoder + RF Remote Control
DA-2801 – Full Feature Decoder
I) DA-2800 & DA-2801
• A Decoder for The DK-2800 Series Keypads in Split-decoded Operation
• Decodes The Data of EM Cards, PINs / Codes & Functions Faithfully from Keypads
• Provides Full Features in Split-Decoded Mode for Any Keypad in The DK-2800 Series
• Simple Three Wires Connection to Keypads For Data Communication, (+), (
- ) & Data I/O
• Easily to Set Up Link Up Code with The Keypads And The Decoder
• Three Independently Controlled Output Relays
• Built-in Door Chime
• Built-in Alarm for Tamper, Door Forced Open and Door Opening in Split-Decoder Mode
• Built-in Current Limited (750mA) Power Source for The Keypads to Prevent Sabotage of Short Circuit from Outside
II) DA-2800 Only
• Provides The Tri-Tech Features of RF Remote Control, Card and PIN/Code Reading in One System
• 24 bits Self-learning Codes (over 1 million codes) for The RF Remote Control Keys
• Accepts 40 RF Remote Control Keys Maximum
• 4 RF Remote Control Channels for Stand Alone or Split-decoded Operation
• Remote Control Key Controls Output 1, 2, 3 & Door Chime
4
41
8 0
Door Forced Open Warning
& Time
FUNCTION MODE / TIME:
0---OFF
1-999 Seconds
80
FUNCTION / TIME
#
Mode = 0,
Door Forced
Open
Warning OFF
8 1
Propped-up Warning & Time
81
FUNCTION / TIME
#
Mode = 0,
Propped-up
Warning OFF
9 0
Egress Delay Warning &
Alarm
CODE 1
- FUNCTION MODE:
1---Momentary, No warning
2---Momentary, with warning
3---Momentary, with warning +
Alarm
4---Hold Contact, No warning
5---Hold Contact, with warning
6---Hold Contact, with warning
+ Alarm
CODE 2
- DELAY TIME:
0---No Delay
1-99 Seconds
90
CODE 1 CODE 2
#
Mode = 1
Momentary,
No warning
TIME = 0
No Delay
9 1
Door Opening Alarm &
TIMER
ALARM TIME:
0---No Alarm
1-999 Seconds
91
ALARM TIME
#
Time = 0,
No Alarm
9 4
Operation Mode & Wiegand
Output
MODES OF WIEGAND OUTPUT
0---Stand Alone Keypad
- Valid
Codes & Cards Only
1---Reader
- All Codes & Cards
2---Master Keypad
- Valid Codes
& Cards only
3---Slave Keypad
- Valid Codes
& Cards only
94
WIEGAND O/P MODE
#
Mode = 0
Keypad Mode
SYSTEM CODES FUNCTION CODE ENTRY RESULTS
0 0 0 0
Factor y Set Master Code
for User to set system in
programming Mode at the
first time.
THIS IS NOT A PERMANENT
S Y S T E M C O D E & I T I S
CHANGED IF A NEW MASTER
CODE IS PROGRAMMED.
0000 * *
OR
NEW MASTER CODE
* *
System in Programming Mode
9 9 9 9
REFRESH CODE -- Refresh
the system and set all its
fun cti on bac k to de fau lt
values.
9999 #
All programmed data are cleared and
back to the default values except the
Master Code
8 0 8 0
DAP CODE-- Direct access
to programming mode. Valid
only in the power-up delay
period
8080 #
System in Programming Mode
0 9 9 9
USER PINs / Codes / Cards
whole group clearance Code
- Key in the Code to clear all
the users in the Location
LOCATIONS:
10--- User Group 1
20--- User Group 2
30--- User Group 3
40--- Vistor Group
41--- Duress Group 1
42--- Duress Group 2
43--- Duress Group 3
LOCATION NO.
0999 #
Whole group of users in the selected
location are cleared
* *
Exit Programming Code
**
The system back to normal opration
after programming