User manual

The home technology brand for the entire house. More information at www.sygonix.com
GB
Operating instructions
Keypad, transponder, IP66,
exposed
• Handle the product with care, it can be damaged by impacts, blows, or
accidental drops, even from a low height.
• If the product is to be used with other equipment (e.g. a door opener),
the operating instructions and safety notices for the connected devices
must be followed.
• It can be assumed that safe operation is no longer possible if:
- the device is visibly damaged,
- the device no longer works
-
the device has been stored under adverse conditions
- it was exposed to heavy loads during transport
• In commercial institutions, the accident prevention regulations of the
Employer’s Liability Insurance Association for Electrical Systems and
Operating Materials are to be observed.
• If you have any questions, which are not answered in this manual,
please contact our technical service or another specialist.
Installation
a) Preparation, choosing the installation site
•
Installation and connection should be carried out by a professional.
The broad range of connection and programming options allow individual con-
fi guration according to need.
We therefore recommend, where possible, programming and testing the sys-
tem before building it into its permanent position.
This helps to plan the wiring correctly and avoids unnecessary trouble-
shooting.
• The keypad can be mounted indoors and outdoors (IP66), but the control unit
must only be installed and used in dry areas.
• The keypad should be installed directly next to the door that is to be equipped
with the keypad.
Make sure when choosing the installation site that the keypad does not ob-
struct opening the door and that the keypad cannot be damaged by the door.
• The control unit should be in a protected and tamper-proof location, so it can-
not be accessed by visitors and guests.
• The cable between the keypad and control unit should not be too long, we
recommend a maximum of 10 m.
Always lay the cable where it is protected and cannot be seen, e.g. in the wall
or in a suitable installation conduit.
• The keypad and control unit must be supplied with a stabilised voltage of 12 -
24 V DC.
The keypad requires a max. current of about 145 mA, and the control unit
about max. 100 mA.
To guarantee the functioning of the keypad and control unit in the case of power
failure, a rechargeable battery system should be used as a back-up voltage /
power supply.
b) Installing the keypad
• Remove the surface-mounting frame from the keypad. There is a special tool
supplied for this purpose.
•
Run the necessary connecting cables to the keypad installation site. We recom-
mend that the cable between the keypad and the controller is not immured the
wall, but rather run inside a suitable installation conduit.
• Fasten the surface-mounting frame to the wall. Use appropriate wall plugs and
screws. Pay attention when drilling and tightening the screws that existing ca-
bles or pipes are not damaged!
• Remove the keypad's rear panel, by removing the four screws.
• Use to connect the enclosed adapter cable to the 6-pin connector, do not
forget the power supply of the keypad! Consult the English manual for circuit
examples.
Close the back of the keypad again, making sure that you do not entangle the
cable.
• Place the keypad in the surface-mounting frame and secure it in place using
the special tool supplied.
Use in accordance with manufacturer's instructions
The product is used, for example, for access control of doors. Separating the lock
code (mounted next to the door) and the control unit (mounted on the inside)
provides an additional interference and access control.
As a special feature, it is not only by possible to access it by entering your user
code, but also by means of a battery-free transponder.
The keypad can be mounted indoors and outdoors (IP66), but the control unit
must only be installed and used in dry areas.
The keypad and the control unit work on an operating voltage of 12 - 24 V / DC.
Any other use than that described above may damage the product. Moreover,
this may give rise to hazards such as short-circuiting, fi re, electric shock, etc. No
part of the product may be modifi ed or converted!
The safety instructions are to be observed without fail!
This product complies with the applicable National and European requirements.
All names of companies and products are the trademarks of the respective owner.
All rights reserved.
Package Contents
• Keypad with surface-mounting frame
• Control unit
• Mounting material (screws, wall plugs, connecting cable)
• Special tool for the keypad housing
• 2 Transponders
• Detailed instructions in English
• Quick guide
Explanation of the Symbols
This symbol indicates specifi c risks associated with handling, function
and use.
The "arrow" symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure
to observe these safety instructions! We do not assume any liabil-
ity for any consequential damage!
Nor do we assume liability for damage to property or personal in-
jury caused by improper use or failure to observe the safety instruc-
tions. In such cases the warranty will be null and void.
• The unauthorised conversion and/or modifi cation of the product is in-
admissible because of safety and approval reasons (CE).
• The product is not a toy and must be kept out of the reach of children.
It should be operated out of the reach of children.
• The code lock is protected according to IP66, it can be installed and
used both indoors and outdoors .
The control unit must only be installed and used in dry rooms.
• The product should not be exposed to extreme temperatures, direct
sunlight, intense vibrations or heavy mechanical stresses.
• Make sure the connection cables are not pinched or damaged by sharp
edges.
• Do not leave packing materials unattended. They may become danger-
ous playthings for children.