User manual

ManualsBrandsSYGONIX ManualsHeating Control SystemsUniversal thermostat Adapter 5 up to 35 °C

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in

electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.

This publication represent the technical status at the time of printing.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in

electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.

This publication represent the technical status at the time of printing.

Timer function

Set-up (and use) is only possible if plug-in thermostat is switched on by the „ “ key

and the temperature is displayed in the lower row.

Selecting operating mode

Refer to the corresponding chapter of these operating instructions.

Switching the timer on/off

• In order to switch the timer on or off, briey press the „P“ key.

• Once the timer is switched on, the symbol „

“ will appear on the display bottom left, and

the timer time bottom right.

Setting timer time and temperature limit

• Switch on the timer rst as described above.

• Hold the „P“ key for approx. 3 seconds until the timer time starts ashing.

• Set the timer time using the „+“ or „-“ key (1....99 hours). For quick adjustment, press and hold

down the corresponding key for longer.

• Briey press the „P“ button. The temperature limit value will ash.

• Use the „+“ or „-“ key to set the temperature limit value. For quick adjustment, press and hold

down the corresponding key for longer.

• In order to quit the set-up mode, briey press the „P“ key. Alternatively, wait for about 10 sec-

onds, without pressing any key. The timer time will stop ashing.

Function of the timer

Example:

The room temperature is e.g. 19 °C and you set the temperature of 25 °C and duration of

5 hours via the timer.

After the start of the timer, the thermostat will control the connected appliance according to the

measured room temperature for the next 5 hours.

Timer operation can be paused and resumed by the „

“ key.

If the timer functions should be terminated, switch off the timer by the „P“ key as described

above.

After expiry of the timer time, the plug-in thermostat will turn off the connected appli-

ance.

If the plug-in thermostat should operate in normal mode after that, switch the ther-

mostat („OFF“ will appear on display) off and on again.

Resetting the plug-in thermostat

To reset the plug-in thermostat to factory settings, press briey the recessed „Reset“ key (on

the right below the „ “ key) e.g. by a toothpick.

Function Factory settings

„COOL“ = cool mode 25 °C

„HEAT“ = heat mode 20 °C

Timer 2 hours

Heating Mode: 16 °C

Cooling Mode: 28 °C

Care and Cleaning

Before cleaning the product, disconnect the appliance from the plug-in thermostat. Disconnect

then the plug-in thermostat from power supply by pulling it out of the mains socket.

Never use abrasive cleaning agents, cleaning alcohol or other chemical solutions, since these

could damage the housing or even impair operation.

Use a dry, lint-free cloth to clean the product.

Disposal

Electronic devices are recyclable material and do not belong in the household

waste. Dispose of an unserviceable product in accordance with the relevant statu-

tory regulations.

Technical Data

Operating voltage ......................... 230 V/AC, 50 Hz

Connection power ......................... Ohmic load: max. 3680 W (230 V/AC, 16 A)

...................................................... Inductive load: max. 460 W (230 V/AC, 2 A)

Devices with mainly resistive load are, e.g., light bulbs, heaters, etc.

Powered devices with inductive load are, e.g., engines, control gears, conventional

transformers, energy-saving bulbs, etc.

Switch type ................................... Relay (single-pole)

Temperature adjustment range ..... Heat mode: +5 °C to +30 °C

...................................................... Cooling mode: +10 °C to +35 °C

Accuracy ....................................... ±/0.5 °C

Backup rechargeable battery ........ yes, built-in permanently (NiMH, 2,4 V); charging time

ca. 14 h, back-up time ca. 30 days

Socket with child protection .......... yes

Ambient conditions ....................... Temperature 0 °C to +40 °C, air humidity 0% to 90% rela-

tive, not condensing

Dimension ..................................... 129 x 55 x 78 mm (H x W x D, including plug)

Weight .......................................... 170 g