Instructions

Intended use
The radio-controlled ush-mounted switch, in combination with a
suitable radio-controlled remote switch of the RSL system is used to
wirelessly switch a connected consumer load on or off.
The radio-controlled ush-mounted switch is only suitable for opera-
tion on the mains voltage (230 V/AC, 50 Hz). A maximum consumer
load of 2300 W (Ohm resistive load) or 300 W (inductive load) can
be connected.
It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or mo-
dify this product. If you use the product for purposes other than those
described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, re, electric shock
etc. Read the instructions carefully and keep them. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European requi-
rements. All company names and product names are trademarks of
their respective owners. All rights reserved.
Safety instructions
Read the operating instructions carefully and espe-
cially observe the safety information. If you do not fol-
low the safety instructions and information on proper
handling in this manual, we assume no liability for any
resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight,
strong jolts, high humidity, moisture, ammable gases, vapours and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions
or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even
from a low height can damage the product.
• Also observe the safety and operating instructions of any other de-
vices which are connected to the product.
• The product may only be installed by a qualied technician (e.g.
electrician) who is familiar with the relevant regulations (e.g. VDE,
German electrical wiring regulations)!
Improper work, carried out on the mains voltage, endangers not
only your own life but also the life of others!
If you do not have the expertise required for the installation, do not
install it yourself but ask a qualied technician.
• Do not use this product in hospitals or medical institutions. Although
the transmitters of the RSL system emit only relatively weak radio
signals, these may lead to malfunction of life-supporting systems.
The same may be the case in other areas.
• The product may only be operated on the mains voltage (see sec-
tion “Installation and Connection” and “Technical Data”). Never try
to operate the product at another voltage as this will cause its de-
struction.
• The installation may only be carried out, if all poles of the mains
supplies of the wireless ush-mounted switch are disconnected
from the mains voltage. Otherwise, there is a mortal danger by an
electric shock!
• An all-pole disconnection from the mains voltage (such as a surge
protector) must be provided as part of the wiring set-up.
• Never touch the product when your hands are wet or damp! There
is a risk of a life-threatening electric shock!
• Only use the product when it is rmly mounted and steady. Insert
the product e. g. into a suitable ush-mounted socket or surface
box.
• If you have reason to assume that safe operation is no longer pos-
sible, disconnect the product immediately and secure it against ac-
cidental operation. Neither touch the wireless ush-mounted switch
nor any connected device.
Disconnect the wireless ush-mounted switch from the mains vol-
tage by switching off the corresponding circuit breaker or removing
the fuse. Furthermore, turn off the earth leakage circuit breaker in
order to disconnect all the poles of the mains supply.
Let an expert check the product.
• In commercial institutions, the accident prevention regulations of
the employer’s liability insurance association for electrical systems
and operating facilities are to be observed!
• Consult an expert when in doubt about operation, safety or connec-
tion of the device.
Latest operating instructions
Download the latest operating instructions via the
link www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when the-
re is a potential risk of personal injury, such as electric
shock.
An exclamation mark in a triangle indicates important ins-
tructions in this operating manual that absolutely have to
be observed.
The arrow symbol indicates specic tips and advice on
operation.
Delivery content
• RSL wireless built-in switch
• Operating instructions
Operating instructions
RSL wireless built-in switch
Item no. 1761743
• Maintenance, modications and repairs are to be performed exclu-
sively by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Preparations for installation
Please observe the chapter “Safety instructions”!
• The wireless ush-mounted switch must be mounted and operat-
ed in a suitable ush-mounted socket or surface box, or in another
housing suitable for this purpose.
• Only use the wireless ush-mounted switch when it is rmly mount-
ed.
• The radio ush-mounted switch must be disconnected from the
power supply during installation. For this purpose, switch off the
electrical mains supply by switching off at the corresponding circuit
breaker or removing the fuse. Secure it against an unauthorised
re-start, e.g. with a danger sign.
Furthermore, turn off the earth leakage circuit breaker in order to
disconnect all poles of the mains supply from mains voltage.
• Check that the mains supply is current free with a suitable tester.
Installation and connection
Observe the chapter “Preparations for installation”
The wireless ush-mounted switch can be used as a complementary
component providing an additional wireless switching function for a
wall switch. This means the existing wall switch is still used. However,
the consumer load (e. g. a room lighting) connected to the wall switch
can now be controlled additionally using a wireless ush-mounted
switch or a wireless remote control of the RSL system.
This implies that the ush-mounted socket provides sufcient space
to install the wireless ush-mounted switch behind the existing wall
switch.
• Loosen the cover of the wall switch and remove the wall switch from
the ush-mounted socket.
• Connect both cables of the wireless
ush-mounted switch with the two
switching contacts of your wall switch
(“S1”), see picture on the right.
• Connect the consumer load to the
two middle screw terminals, see pic-
ture on the right.
The connection “N” is the neutral
conductor, the connection “ ” is
the connected output/phase/L.
• The outer two screw terminals are
used for the connection to the mains
voltage (“N” = neutral conductor, “L”
= phase).
• Insert the wireless ush-mounted switch into the ush-mounted
socket.
Pay attention that the push-button on the housing’s rear is exposed
during installation and not accidentally pushed.
S1
NN
L