Instructions

Intended use
The wireless switch is intended for wireless switching on and off con-
nected devices using suitable radio transmitter of the RS2W system.
The wireless switch may only be used on mains voltage (230 V/AC,
50 Hz). A maximum consumer load of 3500 W/15.2 A (resistive load)
or 600 W/2.6 A (inductive load) can be connected.
It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or mo-
dify this product. If you use the product for purposes other than those
described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, re, electric shock
etc. Read the instructions carefully and keep them. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European requi-
rements. All company names and product names are trademarks of
their respective owners. All rights reserved.
Safety instructions
Read the operating instructions carefully and espe-
cially observe the safety information. If you do not fol-
low the safety instructions and information on proper
handling in this manual, we assume no liability for any
resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight,
strong jolts, high humidity, moisture, ammable gases, vapours and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions
or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even
from a low height can damage the product.
• Also observe the safety and operating instructions of any other de-
vices which are connected to the product.
• This product may only be installed by a qualied technician (e.g., an
electrician) who is familiar with the relevant regulations (e.g., VDE,
German electrical wiring regulations)!
• Improper work carried out on the mains voltage endangers not only
your own life, but also the life of others!
• If you do not have the expertise required for the installation, do not
install it yourself but ask a qualied technician.
• Only use the product when it is securely installed and steady. Install
the product, e.g. in a suitable ush or wall-mounted box or other
suitable housing, so that the required protection against contact is
ensured.
• Keep the product out of strong magnetic elds that occur near ma-
chines, electric motors or loudspeakers.
• Do not use this product in hospitals or medical institutions. Although
RS2W radio system transmitters only emit relatively weak radio si-
gnals, these may lead to the malfunctioning of life-support systems.
The same may also apply to other zones.
• Never touch or handle the product with damp or wet hands. There is
a risk of a life-threatening electric shock!
• Only carry out the installation when all the mains cables to the wi-
reless switch are disconnected from the mains voltage. Otherwise,
there is a risk of a life-threatening electric shock!
• An all-pole disconnection from the mains voltage (such as a surge
protector) must be provided as part of the wiring set-up.
• Never connect the product to the power supply immediately after it
has been transferred from a cold room into a warm one (e.g., during
transport). Condensation water that forms might destroy the device.
Moreover, there is danger of electric shock!
Allow the device to reach room temperature before switching it on.
Wait until the condensation has evaporated. This might take several
hours. Only after this should it be plugged in to the mains supply
and put into use.
• Never overload the product. Observe the maximum connected load
allowed in the “Technical Data” chapter.
• Do not use the product if it is damaged. There is a risk of a life-
threatening electric shock! In this case, dispose of the product in an
environmentally correct manner.
• If it can be assumed that safe operation is no longer possible, the
device must be turned off and precautions must be taken to ensure
that it is not used unintentionally. Do not touch the wireless switch
or any device connected to it.
Latest operating instructions
Download the latest operating instructions via the
link www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when the-
re is a potential risk of personal injury, such as electric
shock.
An exclamation mark in a triangle indicates important ins-
tructions in this operating manual that absolutely have to
be observed.
The arrow symbol indicates specic tips and advice on
operation.
The product is only intended to be installed and used in
dry, indoor rooms; it must not get damp or wet.
Observe the operating instructions!
Delivery content
• RS2W wireless switch micro
• Operating instructions
Operating instructions
RS2W wireless switch micro
Item no. 1761759
Disconnect the wireless switch from the mains by switching off at
the appropriate circuit breaker or by pulling out the fuse. Further-
more, turn off the earth leakage circuit breaker to disconnect all the
poles of the mains supply.
• Use the product only in a temperate climate, never in a tropical
climate.
• Consult an expert when in doubt about operation, safety or connec-
tion of the device.
• Maintenance, modications and repairs are to be performed exclu-
sively by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Preparations for installation
Please observe the chapter “Safety instructions”!
• To use, install the wireless switch in a suitable ush or wall-mounted
box or other suitable housing.
• The wireless switch must be disconnected from the power supply
during installation. First, switch off all poles of the mains supply
by switching off at the associated circuit breaker or removing the
fuse and then also switch off the associated RCD (residual current
device).
Secure it against unauthorised reconnection, e.g., with a danger
sign. Check the mains connection for absence of voltage using a
suitable tester.