Instructions

Intended use
The set contains a wireless wall mounted switch (inbuilt switch) and
a wall-mounted radio transmitter. A consumer connected to the inbuilt
switch can be turned on and off remotely via the wall-mounted radio
transmitter (or via another radio remote switch in the RSL system).
The wireless inbuilt switch may only be used on the mains voltage
(230 V/AC, 50 Hz). A maximum consumer load of 2000 W (Ohm resis-
tive load) or 300 W (inductive load) can be connected and switched.
The wireless inbuilt switch is powered by a 12 V battery type “27 A”.
It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or mo-
dify this product. If you use the product for purposes other than those
described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, re, electric shock
etc. Read the instructions carefully and keep them. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European requi-
rements. All company names and product names are trademarks of
their respective owners. All rights reserved.
Safety instructions
Read the operating instructions carefully and espe-
cially observe the safety information. If you do not fol-
low the safety instructions and information on proper
handling in this manual, we assume no liability for any
resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight,
strong jolts, high humidity, moisture, ammable gases, vapours and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions
or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even
from a low height can damage the product.
• Also observe the safety and operating instructions of any other de-
vices which are connected to the product.
• The product may only be installed by a qualied technician (e.g.
electrician) who is familiar with the relevant regulations (e.g. VDE,
German electrical wiring regulations)!
Improper work, carried out on the mains voltage, endangers not
only your own life but also the life of others! If you do not have the
expertise required for the installation, do not install it yourself but
entrust a qualied electrician.
• Do not use this product in hospitals or medical institutions. Although
RSL System transmitters only emit relatively weak radio signals,
these may lead to the malfunctioning of life-supporting systems.
The same may possibly be the case in other areas.
• The wireless inbuilt switch may only be operated on the mains volt-
age (230 V/AC, 50 Hz). The wall-mounted radio transmitter may
only be operated using a 12 V battery of type “27 A”.
• Only carry out the installation when all the mains cables to the in-
built wireless switch are disconnected from the mains voltage. Oth-
erwise, there is a risk of a life-threatening electric shock!
• Never touch the wireless inbuilt switch with wet or damp hands!
There is a risk of a life-threatening electric shock!
• An all-pole disconnection from the mains voltage (such as a surge
protector) must be provided as part of the wiring set-up.
• Only use the product when it is securely installed and steady. Install
the wireless inbuilt switch, for example, in a suitable ush or wall
mounted contact box. Install the wall-mounted radio transmitter, for
example, on a wall or furniture surface.
• If you have reason to assume that safe operation is no longer pos-
sible, disconnect the product immediately and secure it against
inadvertent operation. Do not touch the inbuilt wireless switch or
any connected device.
Disconnect the inbuilt wireless switch from the mains by switching
off the appropriate circuit breaker or pulling out the fuse. Further-
more, turn off the earth leakage circuit breaker to disconnect all the
poles of the mains supply.
Let an expert check the product.
• In commercial institutions, the accident prevention regulations of
the employer’s liability insurance association for electrical systems
and operating facilities are to be observed!
Latest operating instructions
Download the latest operating instructions via the
link www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when the-
re is a potential risk of personal injury, such as electric
shock.
An exclamation mark in a triangle indicates important ins-
tructions in this operating manual that absolutely have to
be observed.
The arrow symbol indicates specic tips and advice on
operation.
Delivery content
• RSL wireless wall switch
• RSL wireless built-in switch
• Battery
• Operating instructions
Operating instructions
RSL wireless built-in switch set
Item no. 1762770
• Consult an expert when in doubt about operation, safety or connec-
tion of the device.
• Maintenance, modications and repairs are to be performed exclu-
sively by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
b) Batteries
• Correct polarity must be observed while inserting the battery.
• The battery should be removed from the device if it is not used for
a long period of time to avoid damage through leaking. Leaking or
damaged batteries might cause acid burns when in contact with
skin, therefore use suitable protective gloves to handle corrupted
batteries.
• Batteries must be kept out of reach of children. Do not leave batte-
ries lying around, as there is risk, that children or pets swallow them.
• Batteries must not be dismantled, short-circuited or thrown into
re. Never recharge non-rechargeable batteries. There is a risk of
explosion!
Installation and connection
Please refer to the section “Safety instructions”!
a) Wall-mounted radio transmitter
• Use a at screwdriver to carefully lever the
rocker switch on the wall-mounted radio
transmitter and remove it.
• Remove the mounting plate, it is fastened
by 4 clips to the electronic sections of the
wall-mounted radio transmitter (see 4 ar-
rows in the middle picture to the right).
• The mounting plate contains several dif-
ferent mounting holes for installation using
screws, for example, in the wall or even on
the surface or in a ush-mounted socket
box. You can also secure the wall-mounted
radio transmitter using double-sided duct
tape.
Use suitable screws and wall plugs, de-
pending on the surface. Pay attention
when drilling and tightening the screws that
no cable or pipes are damaged.
• Insert the electronic section, correctly
orientated, into the mounting plate, until it
locks in place. The arrow on the electronic section (see circle in the
middle picture to the right) indicates the position “up” (rocker switch
inscription “I”).
• Insert a 12 V battery (Type “27 A”), with the correct polarity, into
the battery compartment of the wall-mounted radio transmitter. An
identical gure is located next to the battery compartment.
• Fit the rocker switch correctly. The inscription “I” on the rocker
switch faces upwards, on the same side as the arrow on the elec-
tronic section, as indicated by a circle in the middle picture.
b) Wireless inbuilt switch
• Install the wireless switch in a suitable ush or wall mounted hous-
ing, contact box or similar.
• The wireless inbuilt switch must be disconnected from the mains
supply during installation. Turn off the mains supply, before switch-
ing off the appropriate circuit breaker or pulling out the fuse. Secure
it against an unauthorised re-start, e.g. with a danger sign.
Furthermore, turn off the earth leakage circuit breaker to disconnect
all the poles from the mains voltage.
• Check that the mains connection is current free with a suitable
tester.
• Connect the consumer load to the two mid-
dle screw terminals, see picture on the right.
The connection “N” is the neutral wire, the
connection “ ” is the connected output/
phase/L.
• The outer two screw terminals are used for
connecting to the mains voltage (“N” = Neu-
tral wire, “L” = Phase).
• Using the two lateral mounting lugs, the
wireless inbuilt switch can be rmly screwed
in place (hole separation for the mounting
lugs = 60 mm).
• The button on the rear of the housing is used to “programme the
switch to a radio transmitter in the RSL switching system (e.g. the
supplied wall-mounted radio transmitter).
Take care that there is enough free space around the pushbutton,
so it will not be switched on by accident.
NN
L