Instrukcja użytkowania System dostępowy RFID Nr zam.
Spis treści Strona 1. Wprowadzenie......................................................................................................................................................4 2. Opis symboli.........................................................................................................................................................4 3. Użytkowanie zgodne z przeznaczeniem...............................................................................................................
Strona 10. Obsługa..............................................................................................................................................................23 a) Pierwsze uruchomienie................................................................................................................................23 b) Dostęp za pomocą ważnego transpondera użytkownika.............................................................................
1. Wprowadzenie Szanowni Klienci! Dziękujemy za zakup naszego produktu. Produkt jest zgodny z obowiązującymi ustawowymi wymogami krajowymi i europejskimi. Aby utrzymać ten stan i zapewnić bezpieczną eksploatację, użytkownik musi przestrzegać niniejszej instrukcji obsługi! Niniejsza instrukcja obsługi jest częścią tego produktu. Zawiera ona ważne wskazówki dotyczące uruchamiania i użytkowania produktu. Należy o tym pamiętać, gdy produkt przekazywany jest osobom trzecim.
3. Użytkowanie zgodne z przeznaczeniem Produkt służy głównie do zabezpieczania dostępu do drzwi (np. biura) lub aktywacji/dezaktywacji systemu alarmowego. W pamięci można zapisać maksymalnie 2000 użytkowników z różnymi transponderami. Przytrzymując zaprogramowany transponder przed powierzchnią odczytu, spowodujemy aktywację bezpotencjałowego styku przełącznego przekaźnika (obciążalność styku patrz rozdział „Dane techniczne”).
5. Wskazówki dotyczące bezpieczeństwa Uszkodzenia spowodowane nieprzestrzeganiem niniejszej instrukcji obsługi powodują unieważnienie rękojmi / gwarancji! Nie ponosimy odpowiedzialności za szkody następcze! Nie ponosimy odpowiedzialności za obrażenia oraz straty materialne spowodowane nieprawidłową obsługą lub nieprzestrzeganiem wskazówek bezpieczeństwa! W takich przypadkach wygasa rękojmia/gwarancja. a) Informacje ogólne • Produkt nie jest zabawką.
b) Wskazówki dotyczące baterii • Baterie należy trzymać poza zasięgiem dzieci. • Nie pozostawiać baterii bez nadzoru z powodu ryzyka połknięcia ich przez dzieci lub domowe zwierzęta. W przypadku połknięcia należy jak najszybciej skontaktować się z lekarzem, ponieważ istnieje ryzyko zagrożenia życia! • Podczas wkładania baterii do pilota IR zwrócić uwagę na prawidłową biegunowość (plus/+ i minus/-). • Baterii nie wolno zwierać, otwierać, rozbierać lub wyrzucać przez okno.
6. Elementy obsługi i złącza 1 Otwór do montażu ściennego 2 Wskaźnik LED 3 Czujnik RFID Na tylnej stronie znajduje się czujnik jasności, który służy jako zabezpieczenie przed sabotażem. Bezpośrednio obok wskaźnika LED (2) znajduje się dioda odbiorcza LED na podczerwień (niewidoczna z zewnątrz).
7. Montaż i podłączenie Nie wolno zaginać ani zaciskać żadnych przewodów przyłączeniowych. Może to prowadzić do nieprawidłowego działania, zwarć i uszkodzenia urządzenia. Podczas wiercenia i dokręcania śrub należy uważaj, aby nie uszkodzić żadnych kabli ani przewodów. Montaż i podłączenie dozwolone są wyłącznie po odłączeniu napięcia.
b) Podłączenie do konwencjonalnego źródła zasilania (napięcia/prądu) Jeśli do zasilania ma zostać użyty standardowy zasilacz, należy przestrzegać poniższych ilustracji ze schematem połączeń. A) Automat do otwierania drzwi „Fail-Secure”: Rygiel blokujący zostaje zwolniony tylko wtedy, gdy doprowadzone jest napięcie robocze (zwykła wersja dla drzwi domowych). B) Automat do otwierania drzwi „Fail-Safe”: zwalnia rygiel blokujący tylko w przypadku braku napięcia roboczego (rzadko spotykana wersja, stosowana np.
d) Interfejs Wiegand Interfejs Wiegand systemu dostępowego można wykorzystać na dwa różne sposoby: 1) System dostępowy działa jako zewnętrzny czytnik kart System dostępowy można podłączyć do odpowiedniego sterownika Wiegand, gdzie służy jako zewnętrzny czytnik kart. Dane z transpondera są przesyłane protokołem 26-bitowym, dlatego stosowany sterownik Wiegand musi go obsługiwać. 1 3 2 Należy przestrzegać instrukcji obsługi sterownika Wiegand.
8. Uruchomienie a) Pilot na podczerwień Bateria pilota na podczerwień jest już włożona przy dostawie. Wystarczy wyciągnąć mały przezroczysty pasek ochronny (zapobiega to przedwczesnemu rozładowaniu baterii) i pilot na podczerwień jest gotowy do pracy. Wymiana baterii jest konieczna, jeśli system dostępowy nie reaguje na pilota na podczerwień. W takim przypadku wystarczy wyciągnąć uchwyt baterii znajdujący się w dolnej części pilota na podczerwień i wymienić zużytą baterię (1x CR2025) na nową.
9. Programowanie Ważne! Zalecamy zanotowanie wszystkich ustawień. W ten sposób nawet po długim czasie możesz prześledzić cały proces programowania i w razie potrzeby dostosować do nowych potrzeb. Należy również zapisać dane dostępowe (np. nazwę użytkownika, numer miejsca w pamięci, numer transpondera), aby mieć wgląd w to, kto ma uprawnienia do dostępu. Dzięki temu można również bardzo łatwo usunąć poszczególne transpondery użytkownika.
b) Zmiana kodu głównego (administratora) Kod główny jest wymagany do całego programowania systemu dostępowego i dlatego należy go odpowiednio wybrać. W ustawieniu fabrycznym w chwili dostawy (lub po przywróceniu ustawień fabrycznych) kod główny (administratora) to „123456”. Ze względów bezpieczeństwa zalecamy zmianę tego kodu głównego najpóźniej po zakończeniu programowania i rozpoczęciu normalnego użytkowania systemu dostępowego. Kod Master (główny) musi składać się zawsze z 6 cyfr.
Automatyczne zapisanie transpondera użytkownika w kolejnym wolnym miejscu w pamięci: Ten proces programowania jest bardzo szybki i łatwy, nowe transpondery użytkownika programuje się w kolejnym wolnym miejscu w pamięci. Jeżeli jednak określony transponder użytkownika ma zostać usunięty (np.
Masowe tworzenie transponderów użytkownika, pod warunkiem że ich numery są kolejne: W przypadku dużej liczby transponderów o kolejnych numerach bez przerw można je zapisać poprzez tworzenie masowe. Ponieważ numery miejsc w pamięci są również kolejne, możliwe jest przyporządkowanie transponderów do numerów miejsc w pamięci, a tym samym usunięcie pojedynczego transpondera poprzez numer miejsca w pamięci w przypadku jego zagubienia lub uszkodzenia.
2) Programowanie transpondera użytkownika za pomocą transpondera głównego Ten proces programowania jest bardzo szybki i łatwy, nowe transpondery użytkownika programuje się w kolejnym wolnym miejscu w pamięci. Jeżeli jednak określony transponder użytkownika ma zostać usunięty (np. w przypadku zagubienia lub uszkodzenia), jest to możliwe tylko poprzez numer transpondera, a nie poprzez numer miejsca w pamięci, ponieważ przyporządkowanie pomiędzy transponderem użytkownika a miejscem w pamięci jest nieznane.
d) Usuwanie pojedynczego transpondera użytkownika Jeżeli dany użytkownik nie ma mieć już więcej dostępu, można usunąć odpowiedni transponder użytkownika. Usunięcie jest możliwe poprzez transponder użytkownika, numer transpondera lub numer miejsca w pamięci. Do usunięcia transpondera użytkownika można także użyć transpondera głównego. 1) Usuwanie transpondera użytkownika za pomocą pilota IR (na podczerwień) • Uruchom tryb programowania zgodnie z opisem w rozdziale 8.
e) Usuwanie wszystkich transponderów użytkownika • Uruchom tryb programowania zgodnie z opisem w rozdziale 8. a) tak, aby dioda LED zaczęła migać na czerwono. • Wprowadź kod programowania do usuwania transponderów. Dioda LED zaświeci się na żółto. • Wprowadź ponownie kod główny. • Wyjdź z trybu usuwania przyciskiem . Dioda LED będzie ponownie migać na czerwono, można teraz dokonać dalszego programowania lub wyjść z trybu programowania przyciskiem .
g) Wybieranie lub wyłączanie zabezpieczenia przed błędnymi wpisami Umożliwia zaprogramowanie, czy system dostępu powinien reagować na 10 lub więcej kolejnych nieprawidłowych wejść przy użyciu zamka (ustawienie domyślne: dezaktywowane). Postępuj w następujący sposób: • Uruchom tryb programowania zgodnie z opisem w rozdziale 8. a) tak, aby dioda LED zaczęła migać na czerwono. • Wprowadź kod programowania dla zabezpieczenia przed błędnymi wpisami. Dioda LED zaświeci się na żółto.
i) Włączanie/wyłączanie diody LED i sygnałów dźwiękowych System dostępowy emituje komunikaty o funkcjach i błędach za pomocą diody LED oraz sygnałów dźwiękowych. Można je włączyć lub wyłączyć (ustawienie domyślne: dioda LED i sygnały dźwiękowe włączone) Postępuj w następujący sposób: • Uruchom tryb programowania zgodnie z opisem w rozdziale 8. a) tak, aby dioda LED zaczęła migać na czerwono. • Wprowadź kod programowania dla diody LED/sygnałów dźwiękowych. Dioda LED zaświeci się na żółto.
1) Resetowanie systemu dostępowego + programowanie transpondera głównego • Odłącz system dostępowy od źródła napięcia/zasilania i poczekaj, aż dioda LED zgaśnie. • Naciśnij i przytrzymaj przycisk automatu do otwierania drzwi. • Podłącz system dostępowy ponownie do napięcia/zasilania. System dostępowy wygeneruje 2 sygnały dźwiękowe. Teraz zwolnij przycisk automatu do otwierania drzwi. • Dioda LED zaświeci się na żółto.
10. Obsługa a) Pierwsze uruchomienie Po podłączeniu i zamontowaniu systemu dostępowego należy włączyć napięcie robocze. Po włączeniu napięcia roboczego system dostępowy wyemituje sygnał dźwiękowy, a dioda LED będzie się świecić stale na czerwono (stan gotowości). System dostępowy jest teraz gotowy do pracy i można go zaprogramować.
b) Dostęp za pomocą ważnego transpondera użytkownika Po rozpoznaniu przez system dostępowy ważnego transpondera użytkownika styk przełączny i sterowany przez niego automat do otwierania drzwi zostaną aktywowane na ustawiony czas, dioda LED zaświeci się na zielono. Po upływie tego czasu dioda LED zaświeci się ponownie na czerwono (tryb gotowości). Jeśli zaprogramowano tryb przełączania (patrz rozdział 8.
11. Usuwanie usterek Po awarii zasilania system dostępowy jest ponownie gotowy do pracy z aktualnymi programowaniem. Jednakże podczas awarii zasilania system dostępowy nie funkcjonuje. W zależności od przeznaczenia – ze względów bezpieczeństwa – zalecamy, aby system dostępowy (podobnie jak w przypadku instalacji alarmowej) był zasilany za pomocą zasilacza bezprzerwowego.
Transponder nie został rozpoznany • Zawsze trzymaj tylko jeden transponder przed czujnikiem RFID (patrz rozdział 6, punkt 3). • Odległość między transponderem a systemem dostępowym powinna wynosić maks. 3 cm. • Można używać wyłącznie transponderów EM o częstotliwości 125 kHz. • Metalowe przedmioty mogą zakłócać działanie transpondera (np. jeśli transponder znajduje się w portfelu z monetami).
12. Czyszczenie i konserwacja Produkt nie wymaga konserwacji. Do okazjonalnego czyszczenia używaj suchej, niestrzępiącej się szmatki. W przypadku mocniejszych zabrudzeń szmatkę lekko zwilżyć wodą. W żadnym wypadku nie stosuj agresywnych środków czyszczących, alkoholu lub innych roztworów chemicznych, ponieważ mogą one odbarwić lub uszkodzić opisy na przyciskach. 13. Utylizacja a) Produkt Urządzenia elektroniczne mogą być poddane recyklingowi i nie zaliczają się do odpadów z gospodarstw domowych.
15. Dane techniczne a) System dostępowy Napięcie robocze ����������������������������������12 - 18 V/DC Pobór prądu ������������������������������������������tryb czuwania <50 mA Pasmo częstotliwości ���������������������������124,6 – 125,4 kHz Moc nadawcza ��������������������������������������11,62 dBm Odległość odczytu ��������������������������������maks. ok.
To publikacja została opublikowana przez Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau, Niemcy (www.conrad.com). Wszelkie prawa odnośnie tego tłumaczenia są zastrzeżone. Reprodukowanie w jakiejkolwiek formie, kopiowanie, tworzenie mikrofilmów lub przechowywanie za pomocą urządzeń elektronicznych do przetwarzania danych jest zabronione bez pisemnej zgody wydawcy. Powielanie w całości lub w części jest zabronione. Publikacja ta odpowiada stanowi technicznemu urządzeń w chwili druku.