Introduction Owner’s Manual INSTRUCCIONES EN ESPAÑOL INCLUIDAS Basic Setup ZC320SL8B Connections Digital Video Disc Recorder Disc Management Recording Playback Editing Function Setup THIS UNIT HAS NO TUNER SYSTEM, YOU MUST CONNECT TO EXTERNAL TUNER. Others © 2007 Funai Electric Co., Ltd. Español IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429, OR VISIT OUR WEB SITE AT http://www.SylvaniaConsumerElectronics.
PRECAUTIONS WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important Safeguards Basic Setup Disc Management Recording Playback Editing Function Setup Others 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 13.
PRECAUTIONS Installation Location For safety and optimum performance of this unit: • Install the unit in a horizontal and stable position. Do not place anything directly on top of the unit. Do not place the unit directly on top of the TV. • Shield it from direct sunlight and keep it away from devices of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the unit.
Introduction PRECAUTIONS Maintenance IR signal check • Please refer to relevant topics on “TROUBLESHOOTING” on pages 80-84 before returning the product. • If this unit becomes inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power plug and please call our help line mentioned on the front page to locate an Authorized Service Center.
CONTENTS Introduction PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Symbols Used in this Owner’s Manual . . . . . . . . . . . . . . . . 7 FUNCTIONAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . 10 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction FEATURES This unit not only plays back DVD and CD but also offers features for you to record on DVD and edit them after that. The following features are offered with this unit. Recording Deleting titles: You can delete titles which you do not need anymore. Setting or clearing chapter marks: You can set or clear chapter marks on titles. Deleting parts of titles: You can delete a specific part of a title. Dividing or combining titles: You can divide or combine a title.
FEATURES Discs for Recording, Playing back Disc type DVD-RW DVD-R Logo Automatically formatted in video mode Format Can be formatted in VR or video mode Video Mode VR Mode Icon Maximum record 480 min (12cm) time 144 min (8cm) 480 min (12cm) 144 min (8cm) 480 min (12cm) 144 min (8cm) Ver.2.0 Ver.2.0/4× Ver.2.0/8× Ver2.0/16× Ver.1.1,1.2 Recordable/playable Ver.1.1/2× CPRM compatible versions Ver.1.2/4× CPRM compatible Playable on most DVD players. Finalization Compatibility necessary.
Introduction FEATURES Discs for playing back Disc Type DVD-VIDEO CD-DA CD-RW CD-R Connections Logo Icon Files for playing back Type of title JPEG CD-RW/-R CD-RW/-R Basic Setup MP3 Icon Media is a trademark of DVD Format/Logo Licensing Corporation. are capable of playing DVD-RW Unplayable Discs Region Codes This unit has been designed to play back DVD with region 1. DVD must be labeled for ALL regions or for region 1 in order to play back on the unit.
FUNCTIONAL OVERVIEW Front Panel 1 3 2* 13 12 4 5 6* 7 11 10 9 8 (*) The unit can also be turned on by pressing these buttons. 1. Disc tray Place a disc when the disc tray is opened. 2. OPEN/CLOSE A button* Press to open or close the disc tray. 3. INPUT button Press to select the appropriate input. 4. PAUSE F button Press to pause playback or recording. 5. STOP C button Press to stop playback or recording. 6. PLAY B button* Press to start or resume playback. 7.
Introduction FUNCTIONAL OVERVIEW Rear Panel 1 2 3 4 L L Connections VIDEO VIDEO IN OUT Y PB/CB R AUDIO IN (L1) 9 IN R S-VIDEO AUDIO OUT 8 7 PR/CR COMPONENT VIDEO OUT OUT COAXIAL S-VIDEO DIGITAL AUDIO OUTPUT PCM / BITSTREAM 6 5 Disc Management 7. AUDIO OUT jacks Use to connect a TV monitor, AV receiver or other device with a RCA audio cable. 8. S-VIDEO IN jack (L1) Use to connect the S-video output of external device with an S-video cable. 9.
FUNCTIONAL OVERVIEW Remote Control Installing the Batteries in the Remote Control Install the batteries (AAx2) matching the polarity indicated inside battery compartment of the remote control. 1 Open the cover. 2 Insert batteries. Using a Remote Control Keep in mind the following when using the remote control: • Make sure that there are no obstacles between the remote control and the infrared sensor window on the unit.
(*) The unit can also be turned on by pressing these buttons. Basic Setup Disc Management Recording Playback 18. CLEAR button Press to clear the password once entered, to cancel the programming for CD, to clear the selecting marker number in the display menu, etc. 19. SETUP button • Press to display the main menu. • During DVD playback, press and hold for more than 3 seconds to switch the progressive scanning mode to the interlace mode. 20. ENTER button Press to confirm or select menu items. 21.
FUNCTIONAL OVERVIEW Front Panel Display 2 1 PM BS CS DR CD VCR DB HDD DVD 3 4 1. PM 3. Current status of the unit : Appears in the afternoon with the clock display. 2. Title / track / file and chapter mark : Appears when indicating a title / track / file number. : Appears when indicating a chapter number. : Appears when playback is paused. : Appears when playing back a disc. : Appears when the timer programming or OTR has been set and is proceeding.
This section describes how to connect this unit to an external tuner such as cable/satellite box. UHF • When you change the connections, all devices shouldVHF be/ turned off. antenna • Refer to the operation manual accompanying external devices for more information. 2 Disconnect Disconnect the power cords of the devices from the AC outlet. or RF coaxial cable Cable TV company disconnect Connections 1 2 rear of your TV ANT. IN Make the connection as illustrated below. e.g.
SETTINGS FOR THE VIDEO INPUT You must let the unit know which video input jack you are using before making a recording. POWER OPEN/CLOSE ZOOM TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST REC SPEED X1.3/0.8 REV SKIP PLAY PAUSE REC/OTR STOP DVD RECORDER NB090 FWD 1 2 3 4 5 Press [SETUP]. Use [K / L] to select “General Setting”, then press [ENTER].
Introduction CONNECTION TO A TV Make one of the following connections, depending on the capabilities of your display device.
CONNECTION TO AN AUDIO SYSTEM 2 Channel Analog Audio Connection Digital Audio Connection stereo system Dolby Digital decoder audio AUDIO IN R L COAXIAL digital audio coaxial input jack analog audio input jacks digital audio coaxial cable RCA audio cable VIDEO VIDEO IN OUT L L VIDEO VIDEO IN OUT Y L this unit PB/CB R AUDIO IN (L1) IN R S-VIDEO AUDIO OUT OUT PR/CR COMPONENT VIDEO OUT L PB/CB R COAXIA DIGITAL AUDIO O PCM / BITSTR S-VIDEO AUDIO OUT Y AUDIO IN (L1) IN R S-VIDE
This unit uses the following on-screen displays and menus to guide you to the easy operations. The on-screen displays give you the information on the loaded disc, the disc/file in playback, etc. The menus allow you to change the various kinds of settings for playing back, recording, or editing to suite your preference. The on-screen display changes in the following order as you press [DISPLAY].
GUIDE TO ON-SCREEN DISPLAYS AND MENUS Main Menu Press [SETUP] to display the main menu. Then use [K / L] to select a menu and press [ENTER] to display the menu. These menus provide entries to all main functions of the unit. Setup 1 2 3 4 5 General Setting Timer Programming Title List DVD Menu CD Playback Mode 1. General Setting: To go to general setting menu. 2. Timer Programming: To program a timer recording. 3. Title List: To call up the title list. 4. DVD Menu: To set up the DVD setting. 5.
You need to follow these steps when you turn on this unit for the first time. OPEN/CLOSE .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST Use [K / L] to select your desired language, then press [ENTER] to set language. Initial Setting OSD Language English Français Español 3 Press [ENTER] to activate “Clock Setting”. Disc Management TIMER PROG. Turn on the TV. Select the input to which the unit is connected.
SETTING THE CLOCK Set the clock before you try the timer programming. Clock Setting POWER OPEN/CLOSE ZOOM TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST REC SPEED REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP STOP CM SKIP REC/OTR 1 2 3 Press [SETUP] and use [K / L] to select “General Setting”, then press [ENTER]. Use [K / L] to select “Clock”, then press [ENTER]. “Clock” menu will appear.
Introduction FORMATTING A DISC Choosing the Recording Format of a Brand-New DVD-RW Use [K / L] to select “DVD Menu”, then press [ENTER]. Setup General Setting Timer Programming Title List DVD Menu POWER TIMER PROG. ABC DEF OPEN/CLOSE INPUT SELECT JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST REV PLAY FWD X1.3/0.
FORMATTING A DISC Reformatting a Disc Manually Insert a recordable disc. If you are using a DVD-RW, you can format the disc by performing “Format”. You can format DVD-RW for either video mode recording or VR mode recording. POWER ZOOM TIMER PROG. ABC DEF OPEN/CLOSE 1 2 Press [SETUP]. Use [K / L] to select “DVD Menu”, then press [ENTER]. Setup General Setting Timer Programming .
Setting for Auto Chapter Introduction PREPARING A DISC Setting Aspect Ratio for Video Mode Recording You can set a specified time for chapter marks. 2) Use [K / L] to select “Recording”, then press [ENTER]. “Recording” menu will appear. 4) Use [K / L] to select a desired time option, then press [ENTER].
SETTING A DISC TO PROTECT To prevent accidental recording, editing or erasing the titles, you can protect them from “DVD Menu”. POWER OPEN/CLOSE ZOOM TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT SPACE DISPLAY TOP MENU MENU/LIST CLEAR SETUP RETURN ENTER REC SPEED REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP REC/OTR STOP CM SKIP 1 2 3 Press [SETUP]. Use [K / L] to select “DVD Menu”, then press [ENTER].
Auto Finalizing OPEN/CLOSE TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST Use [K / L] to select “Recording”, then press [ENTER]. “Recording” menu will appear. Use [K / L] to select “Auto Finalize”, then press [ENTER]. Disc Management ZOOM “General Setting” menu will appear. Basic Setup POWER 1 2 3 4 Press [SETUP] and use [K / L] to select “General Setting”, then press [ENTER].
PLAYING THE DISCS IN OTHER DVD PLAYERS Finalizing a Disc You will need to finalize discs to play back on other DVD players. Finalizing may take several minutes up to an hour. Since the process of the finalization fills empty space of the disc, a shorter recording period on the disc will require a longer time period for finalization. Do not unplug the power cord during finalization. POWER OPEN/CLOSE ZOOM TIMER PROG. .
Note Press [STOP C] during the finalizing is in progress. Use [K / L] to select “Yes”, then press [ENTER]. Finalizing is canceled and the unit switches to stop mode. Do you want to cancel ? Yes No Finalizing ON If “ ” appears when [STOP C] is pressed, you cannot cancel finalizing because the finalizing has already reached at a critical point in its process. If “No” is selected and [ENTER] or [RETURN ] is pressed, finalizing is continued. You cannot cancel finalizing DVD-R once it has started.
INFORMATION ON DVD RECORDING Recording Speed Restrictions on Recording You can select a recording speed among 5 options, and the recording time will depend on the recording speed you select as follows. Recording speed XP / 1H SP / 2H LP / 4H EP / 6H SLP / 8H Recording time 12cm 8cm Video/ sound quality 60 min 18 min 120 min 36 min 240 min 72 min 360 min 108 min 480 min 144 min • The recording times listed above are estimates and are for reference purposes only. Actual recording times may vary.
Follow the steps to record TV programs from an external tuner. This unit has no tuner system so cannot receive TV broadcasts without external tuner or such devices. OPEN/CLOSE .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP STOP CM SKIP REC/OTR 3 Press [OPEN/CLOSE A] to close the disc tray. It may take awhile to load the disc completely.
BASIC RECORDING & ONE-TOUCH TIMER RECORDING 6 Press [REC/OTR] to start recording. “I” will be displayed for 5 seconds. 7 Press [STOP C] to stop recording. The recorded title will be included in the title list. (Refer to “Guide to a Title List” on page 55.) I Press [PAUSE F] to pause recording. Press [PAUSE F]] or [REC/OTR] again to restart recording. Wait for a moment. 90% This operation may take awhile to be completed. To set one-touch timer recording (OTR)...
OPEN/CLOSE .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST 2 JAN/ 2/07 12:00 AM L1 SP 2H (1:00) MON JAN/01 10:00AM Date JAN/02 Start End 12:00AM 1:00AM New Program L1/L2 L1 1/1 4 5 1. Title of a timer program (Contains date, time, channel, recording speed of the program) 2. Current date and time 3. Recording speed and length of the recording 4. Timer program list 5.
TIMER RECORDING 4 Use [K / L / { / B] or [the Number buttons] to enter the start and end time, then press [B]. Date JAN/02 L1/L2 L1 Start 12 : 00AM Speed 2H End --:-- 2H 5 2 : 00 Use [K / L] to select the appropriate external input position (L1/L2) to which your external tuner is connected, then press [B]. Date JAN/02 L1/L2 L1 Start 12 : 00AM Speed 2H 7 End 1 : 00AM 2H 1 : 00 8 Press [ENTER] when all items are entered. Your program setting will be stored.
Checking, canceling, or correcting the timer programming information 1) Press [POWER]. If the timer program did not complete correctly, the error number appears in the timer programming list. Connections will disappear on the front panel display. Timer Programming 2) Press [TIMER PROG.]. TUE JAN/02 10:00AM E41 3) Check the information on the list you want to edit.
TIMER RECORDING Hints for Timer Recording • If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer programming will be lost. • If a disc is not inserted, flashes and timer recording cannot be performed. In some cases, will appear momentarily around the start point as the unit attempts to record. Please insert a recordable disc. flashes.
Use [K / L] to select “Satellite Link”, then press [ENTER]. Timer Programming Timer Programming Satellite Link OPEN/CLOSE TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP Recording ZOOM Satellite Link Start Speed 5:00PM 2H Disc Management 4 Use [K / L] to select the time and recording speed, then press [ENTER]. Use [K / L] to select “Timer Programming”, then press [ENTER]. Basic Setup POWER 1 2 3 Press [SETUP].
SATELLITE LINK 7 8 Press [ENTER]. “To Standby Mode” is highlighted. Press [ENTER] again. Satellite Link Start Speed 5:00PM 2H To Standby Mode In a second, the unit will be turned off automatically as it goes into the satellite link standby mode. To cancel the satellite link function while in the satellite link standby mode: Press [POWER] to turn on the unit. To cancel the satellite link function while the satellite link recording is in progress: Press [STOP C] on the front panel of the unit.
Connection to an External Device Introduction SETTINGS FOR AN EXTERNAL DEVICE Connect the external device properly to either L2 (front) or L1 (rear) input jacks of this unit by using S-video or RCA audio / video cables. Connections or S-VIDEO OUT VIDEO OUT AUDIO OUT L R VIDEO OUT external device AUDIO OUT L R S-VIDEO OUT (camcorder, VCR etc.
SETTINGS FOR AN EXTERNAL DEVICE Recording from an External Device Before recording from an external device, refer to the instructions for the connection on page 39. POWER OPEN/CLOSE ZOOM TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST REC SPEED REV PLAY FWD X1.3/0.
Introduction INFORMATION ON PLAYBACK Structure of Disc Contents DVD video Title: title 1 title 2 chapter 1 chapter 2 chapter 1 chapter 2 chapter 3 Chapter: audio CD track 1 track 2 track 3 track 4 track 5 MP3 / JPEG folder 1 file 1 file 2 folder 2 file 3 file 4 Disc Management Each title, chapter, or track, folder or file is assigned a number, which is called “title number”, “chapter number”, “track number”, “folder number” or “file number” respectively.
BASIC PLAYBACK Direct Playback POWER OPEN/CLOSE ZOOM TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST REC SPEED REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP REC/OTR STOP CM SKIP DVD RECORDER NB090 Note • Some discs may start playback automatically. 42 EN 1 2 Press [POWER]. Turn on the TV and be sure to select the input to which the unit is connected.
Introduction BASIC PLAYBACK Playback from the Title List OPEN/CLOSE .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP STOP CM SKIP REC/OTR 3 Press [OPEN/CLOSE A] to close the disc tray. It may take awhile to load the disc completely. Title list will appear automatically. • To exit the title list, press [STOP C]. • To resume the title list, press [TOP MENU].
BASIC PLAYBACK Playing Back an Audio CD and a CD-RW/-R with MP3 / JPEG Files POWER OPEN/CLOSE ZOOM TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP TOP MENU MENU/LIST RETURN ENTER REC SPEED REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP STOP CM SKIP REC/OTR DVD RECORDER NB090 Press [OPEN/CLOSE A] to close the disc tray. It may take awhile to load the disc completely. File list will appear automatically.
Playing Back an Audio CD and a CDRW/-R with MP3 JPEG Files (cont’d) Kodak Picture CD DVD may contain a title list, which describes the contents of the disc, or a disc menu, which guides you through the available functions in the disc. 1) Press [MENU/LIST] or [TOP MENU] to call up the title list or disc menu. 2) Use [K / L / { / B] to make a selection, and then press [ENTER] to enable your selection. Image 1 3) Press [STOP C] to exit the disc menu.
SPECIAL PLAYBACK Resume Playback You can play back from where you stopped playing back the disc last. 1) During playback, press [STOP C]. The resume message will appear. Skipping TV Commercials During Playback You can skip TV commercials to enjoy the recorded programs without interrupting. Resume ON 2) Press [PLAY B]. In a few seconds, playback will resume from the point at which it stopped last. You can resume playback at the same point even if you turn off the unit.
Rapid Playback B B Press [Bx1.3/0.8] once during playback. Plays back approximately at 0.8 times of normal playback. : : Press [Bx1.3/0.8] thrice to play back in normal speed. No effects. 2) Press [PLAY B] to resume the normal playback. pause 1/16x 1/8x 1/3x To return to the normal playback, press [PLAY B]. Note • Forward/reverse speed will be indicated with icons as follows. forward (approx. speed) 1/16x: 1/8x: 1/3x: reverse (approx.
SPECIAL PLAYBACK Marker Setting Zoom 1) During playback, press [DISPLAY]. 2) Use [{ / B] to select , then press [ENTER] within 1 second, or wait for 1 second to display the selection menu. e.g.) DVD-video 1/ 5 1/ 5 0:01:00 / 1:23:45 DVD Video This feature allows you to assign a specific point on a disc to be called back later. 1) During playback, press [DISPLAY]. 2) Use [{ / B] to select , then press [ENTER] within 1 second, or wait for 1 second to display the marker list. e.g.
Title/Chapter Search Introduction SEARCH Track Search 1) During playback, press [SKIP i ] to skip the current title or chapter and move to the next. The title or chapter will move forward by one at a time. • If there is no chapter in one title, the current title will be skipped. 1) During playback, press [SKIP i] to skip the current track/file and move to the next. The track/file will move forward one at a time. To go back to the beginning of the current track/file, press [SKIP j ].
SEARCH Time Search 1) During playback, press [DISPLAY]. 2) Use [{ / B] to select e.g.) DVD-video 1/ 5 , then press [ENTER]. 1/ 5 0:01:00 / 1:23:45 DVD Video e.g.) audio CD 1/ 5 0:00:15 / 0:05:00 CD The number next to will be highlighted. To move to the number next to , press [B]. When time search is not available, counter are not displayed. and time 3) Use [K / L / { / B] or [the Number buttons] to enter a desired time to search, then press [ENTER].
Repeat Playback Note 2) Use [{ / B] to select , then press [ENTER] within 1 second, or wait for 1 second to display the selection menu. 1/ 5 1/ 5 0:01:00 / 1:23:45 • Point B for the repeat A-B playback should be set within the same chapter or track of point A. • To cancel the repeat playback, select “OFF” at step 3. The repeat setting will also be canceled when you stop playback. • You cannot select “Group” during the random playback of MP3/JPEG files.
REPEAT/RANDOM/PROGRAM PLAYBACK/SLIDE SHOW Program Playback Slide Show You can program the disc to play back in your desired order. You can select the display time between 5 seconds and 10 seconds. 1) Press [SETUP] in stop mode. 1) Follow steps 1 and 2 in “Program Playback” on the left. 2) Use [K / L] to select “CD Playback Mode”, then press [ENTER]. “CD Playback Mode” menu will appear. 2) Use [K / L] to select “Slide Show”, then press [ENTER].
You can select the format of audio and video as you prefer depending on the contents of the disc you are playing back. Switching Subtitles Switching Audio Soundtrack When playing back a DVD-video recorded with 2 or more soundtracks (these are often in different languages), you can switch them during playback. When playing back audio CD, you can switch “L/ R”(stereo), “L”(left) or “R”(right). Connections DVD-video may have subtitles in one or more languages.
SELECTING THE FORMAT OF AUDIO AND VIDEO Switching Virtual Surround System You can enjoy stereophonic virtual space through your existing 2 channel stereo system. 1) During playback, press [DISPLAY]. 2) Use [{ / B] to select , then press [ENTER] within 1 second, or wait for 1 second to display the selection menu. e.g.) DVD-video 1/ 5 1/ 5 Switching Camera Angles Some DVD-video have scenes shot from 2 or more angles. Angle information should be on the disc case if the disc contains multi-angle scenes.
Guide to a Title List Editing Discs Press [TOP MENU]. 4 5 6 Title List JAN/ 1/07 12:00AM L1 LP 12:00PM (2:00:00) JAN/ 1/07 L1 LP 2 3 4 5 6 1/2 2 1 ORG 3 Edit 2 Scene Delete Edit Title Name Chapter Mark Protect 1 : 25 : 47 11 10 9 8 7 ORG PL • Once a disc is finalized, editing the disc or recording to the disc will not be available (except DVD-RW in VR mode). • A playlist is not available with the DVD-R and DVDRW in video mode.
DELETING TITLES Notes for deleting titles After the disc is fully recorded: DVD-RW • When the last title is deleted from DVD-RW in video mode, the recordable space will be increased. TITLE 2 TITLE 2 TITLE 3 The deleted title cannot be created the space. TITLE 3 TITLE 2 TITLE 2 TITLE 3 TITLE 2 TITLE 2 TITLE 3 You cannot record a new title. Delete! TITLE 1 You can record a new title. TITLE 1 Delete! TITLE 1 Delete! TITLE 1 TITLE 1 You can record a new title.
You can delete titles which you do not need anymore. Please be advised that the titles once deleted cannot be brought back to the disc. Be sure to read “Notes for deleting titles” on page 56 before you delete the title. ABC DEF OPEN/CLOSE INPUT SELECT Use [K / L/ s / B] to select a desired title, then press [ENTER]. e.g.
CREATING/DELETING PLAYLIST Adding Titles to a Playlist Playlist For VR mode DVD-RW, you can create the playlist as you wish. You can add up to 99 titles to a playlist (as long as the total number of the playlist does not exceed 999 chapters). POWER .@/: GHI ZOOM TIMER PROG. ABC DEF JKL MNO OPEN/CLOSE INPUT SELECT 1 2 3 AUDIO Follow the step 1 in “DELETING TITLES” on page 57 to display the original. Use [K / L/ s / B] to select the desired title, then press [ENTER].
Introduction CREATING/DELETING PLAYLIST Erasing All Playlist Playlist POWER OPEN/CLOSE .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT SPACE TOP MENU MENU/LIST CLEAR SETUP RETURN ENTER REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP REC/OTR STOP CM SKIP 4 DVD Menu Format Finalize Disc Protect OFF ON Delete All Playlists Use [K / L] to select “Yes”, then press [ENTER].
EDITING DISCS Putting Names on Titles You can put a name on the disc and change it from this menu. POWER OPEN/CLOSE ZOOM TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT 4 Use [K / L] to select “Edit Title Name”, then press [ENTER].
Introduction EDITING DISCS Putting Names on Titles (cont’d) Guide to Edit Title Name .@/: ZOOM TIMER PROG. ABC DEF OPEN/CLOSE INPUT SELECT Select Press JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE TOP MENU MENU/LIST CLEAR SETUP RETURN ENTER PLAY FWD X1.3/0.8 SKIP PAUSE SKIP STOP CM SKIP REC/OTR DVD RECORDER 0 (*1) (*1) 1 ! ”# $ % & ’( ) *+,-.
EDITING DISCS Setting or Clearing Chapter Marks Original Playlist You can put chapter marks in each title. Once a chapter is marked, you can use it for the chapter search feature. POWER OPEN/CLOSE ZOOM TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST 1 2 3 Follow steps 1 to 3 in “Putting Names on Titles” on page 60 to display “Edit” menu.
Introduction EDITING DISCS Deleting a Part of a Title Original Playlist 3 Use [SKIP H / G], [REV E], [FWD D], [PLAY B] and [PAUSE F] to find the start point, then press [ENTER]. PL POWER Edit - Scene Delete OPEN/CLOSE TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER 1 Start End Preview Delete Basic Setup ZOOM Connections You can delete a specific part of a title.
EDITING DISCS Deleting a Part of a Title (cont’d) 4 Use [K / L] to select “Delete” then press [ENTER]. PL Edit - Scene Delete 1 Start End Preview Delete JAN/ 1/07 12:00AM L1 LP 1 : 40 : 00 5 Use [K / L] to select “Yes” then press [ENTER]. “Are you sure?” will appear. Select “Yes” using [K / L] and then press [ENTER]. PL Edit - Scene Delete 1 Are you sure? Yes No JAN/ 1/07 12:00AM L1 LP 1 : 40 : 03 The part of the title is deleted. 6 Press [RETURN ] and then [RETURN ] or [STOP C] to exit.
Introduction EDITING DISCS Dividing a Title Playlist POWER OPEN/CLOSE TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT Use [K / L/ s / B] to select a desired title, then press [ENTER]. Use [K / L] to select “Edit”, then press [ENTER]. e.g.) VR mode DVD-RW playlist PL Title List JAN/ 1/07 12:00AM L1 LP 12:00PM (2:00:00) JAN/ 1/07 DISPLAY SPACE CLEAR TOP MENU MENU/LIST RETURN SETUP REV PLAY FWD X1.3/0.
EDITING DISCS Combining Titles Playlist You can combine 2 titles into a single title. POWER OPEN/CLOSE ZOOM TIMER PROG. .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER 1 2 Follow the steps 1 to 3 in “Dividing a Title” on page 65 to display “Edit” menu. Use [K / L] to select “Title Combining”, then press [ENTER].
Introduction EDITING DISCS Setting or Releasing the Title Protection Original ORG 1 .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER JAN/ 1/07 12:00AM L1 LP 1 : 25 : 47 • If the title is protected, original list. • If the title is already protected, “ON OFF” will appear. If you press [ENTER], the title will be released from protection. PLAY FWD X1.3/0.
EDITING DISCS Setting or Clearing All Chapter Marks at Once For titles in video mode DVD-RW, you can set or edit chapter at every time interval. You can clear the chapter mark too. You can specify the interval of chapter marks for titles last more than 5 minutes. 1 2 Follow the steps 1 to 3 in “Putting Names on Titles” on page 60 to display “Edit” menu. Use [K / L] to select “Chapter Mark”, then press [ENTER]. Video Edit 1 POWER OPEN/CLOSE ZOOM TIMER PROG. .
Introduction LIST OF SETTINGS The following table is the contents which you can set and the default settings. Refer to the following table for useful operation. Setup Playback Audio Out → page 73 Dynamic Range Control ON OFF Compressing the range of sound volume. PCM 48kHz 96kHz PCM Stream English French Spanish Other Set whether the sound recorded in 96kHz will be down sampled in 48kHz. Original English French Spanish Other OFF English French Spanish Other Set the language for audio.
LIST OF SETTINGS Setup Video Items (highlight is the default) Progressive → page 78 TV Aspect → page 78 Select Video L1(Rear) → page 16 General Setting L2(Front) Recording Auto Chapter → page 25 Auto Finalize → page 27 Disc Full End of Timer Rec Aspect Ratio(Video mode) → page 25 Clock Reset All → page 79 Clock Setting → page 22 ON OFF 4:3 Letter Box 4:3 Pan & Scan 16:9 Wide Video In S-Video In Video In S-Video In OFF 5 minutes 10 minutes 15 minutes 30 minutes 60 minutes ON OFF ON OFF Auto 4:3 16:9
Introduction SETUPS Playback Press [STOP C] if you are playing back a disc. OPEN/CLOSE .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP STOP CM SKIP REC/OTR 3 General Setting Playback Display Video Recording Clock Reset All 1 2 3 4 5 6 7 Recording REC SPEED Use [K / L] to select a desired item, then press [ENTER].
SETUPS Playback (cont’d) 1 Parental Lock (Default: All) Some DVD-video feature a parental lock level. Playback will stop if the ratings exceed the levels you set, it will require you to enter a password before the disc will playback. This feature prevents your children from viewing inappropriate material. Use [K / L] to select the desired level, then press [ENTER]. A Use [K / L] to select “Yes”, then press [ENTER]. Use [the Number buttons] to enter a new password except for 4737, then press [ENTER].
Introduction SETUPS Playback (cont’d) 2 C Audio Out Use [K / L] to select a setting, then press [ENTER]. General Setting Use [K / L] to select a desired item, then press [ENTER].
SETUPS Playback (cont’d) 5 Subtitle Language (Default : OFF) Set the subtitle language. Use [K / L] to select a language, then press [ENTER]. 6 Angle Icon (Default : ON) Set to “ON” to show the angle icon during the playback. Use [K / L] to select a setting, then press [ENTER].
Introduction SETUPS Display Press [STOP C] if you are playing back a disc. OPEN/CLOSE .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST 1 2 3 Use [K / L] to select “Display”, then press [ENTER]. Use [K / L] to select a desired item, then press [ENTER]. 1 OSD Language 2 Screen Saver 3 FL Dimmer Disc Management TIMER PROG. Selection menu will appear. REV PLAY FWD X1.3/0.
SETUPS Display (cont’d) 1 OSD Language (Default : English) Set the language for the on-screen display. Use [K / L] to select a setting, then press [ENTER]. General Setting Playback Display Video Recording Clock Reset All OSD Language Screen Saver OSD Language FL Dimmer English Français Español Your setting will be activated. 2 Screen Saver (Default : 10 minutes) Set the time to activate the screen saver function on the TV screen. Use [K / L] to select a setting, then press [ENTER].
Introduction SETUPS Video Press [STOP C] if you are playing back a disc. OPEN/CLOSE .@/: ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST Use [K / L] to select “Video”, then press [ENTER]. Use [K / L] to select a desired item, then press [ENTER]. 1 Progressive 2 TV Aspect 3 Select Video Submenu will appear. REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP STOP CM SKIP REC/OTR Device“ on page 39.
SETUPS Video (cont’d) 1 2 Progressive (Default : OFF) This unit is compatible with the progressive scan system. The feature provides you with the higher definition images than the traditional output system does. To utilize this feature, you must set progressive scan mode to “ON”. 1) Use [K / L] to select “ON“, then press [ENTER].
Introduction SETUPS Reset All Reset the setting to default. OPEN/CLOSE ABC DEF INPUT SELECT GHI JKL MNO AUDIO PQRS TUV WXYZ REPEAT DISPLAY SPACE CLEAR SETUP RETURN ENTER TOP MENU MENU/LIST REV PLAY FWD X1.3/0.8 SKIP PAUSE SKIP STOP CM SKIP REC/OTR NB090 4 Reset to factory default? Yes No Select “Yes” again using [K / L] , then press [ENTER].
TROUBLESHOOTING Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. Symptom Power The power does not turn on. Picture There is no picture. Remedy • Check that the AC power cord is connected securely. • Check the breaker (in case of power failure). • Re-connect the connecting cords securely.
Symptom Playback The disc does not play back. Remedy Connections • No disc is inserted. • A blank disc is inserted. • The disc is upside down. Insert the disc with the labeled side facing up. • The disc is not correctly inserted. • The unit cannot play back certain discs (such as a CD-ROM) (page 9). • The region code on the DVD-video does not match the unit (page 9). • Moisture has condensed inside the unit.
TROUBLESHOOTING Symptom Others The unit does not operate properly. Remedy • When static electricity, etc., causes the unit to operate abnormally, unplug the unit and then plug it in again. The disc tray does not open when you press [OPEN/CLOSE A]. • It may take a few seconds for the disc tray to open after you have recorded or edited a disc. This is because the unit is adding disc data to the disc. “Repairing” appears on the TV screen.
Error message • You cannot record copy prohibited programs. • Set “Format Mode” to “VR mode” (page 23). • You are trying to record on to the protected disc which is set in “DVD Menu” menu. • You are trying to record onto the disc which has no space for recording. • Release the disc protect setting in “DVD Menu” menu (page 26). • Insert the recordable disc with enough recording space. • You are trying to record onto the DVDRW/-R on which the number of recording titles comes up to the maximum (99).
TROUBLESHOOTING Frequently Asked Questions – Can I record to CD-RW/-R? No, this unit records only DVD. – Can I play back DVD-video that is bought in another country? Possible when the region code of the disc is 1 and All. – Can I connect the unit to my PC? No, you cannot control the unit by PC. – Can I program a timer recording with an external tuner? Yes, you can. Select “L1” or “L2” as your recording channel, and leave the external tuner on (pages 15, 3336).
Editing Function Setup Code 6467 6559 6553 6547 5350 6564 6554 6566 6660 6560 6550 6555 6565 6557 6558 6561 5165 6567 6569 6568 6658 6653 6647 6666 6651 6654 4861 6655 6661 6665 6664 6657 6669 6757 6764 6772 6855 6861 4971 6961 7054 5655 7161 7267 Playback Language Russian Samoan Sangho Sanskrit Scots Gaelic Serbian Serbo-Croatian Sesotho Setswana Shona Sindhi Singhalese Siswat Slovak Slovenian Somali Spanish Sundanese Swahili Swedish Tagalog Tajik Tamil Tatar Telugu Thai Tibetan Tigrinya Tonga Tsonga Tu
GLOSSARY Analog Audio PCM (pulse code modulation) An electrical signal that directly represents sound. Compare this to digital audio which can be an electrical signal, but is an indirect representation of sound. See also “Digital Audio”. The most common system of encoding digital audio, found on CD and DAT. Excellent quality, but requires a lot of data compared to formats such as Dolby Digital and MPEG audio.
Introduction SPECIFICATIONS • This model complies with the below specifications. • Designs and specifications are subject to change without notice. • This model may not be compatible with features and/or specifications that may be added in the future. 13.
ESPAÑOL Discos grabables y reproducibles Tipo de disco DVD-RW DVD-R Logotipo Formato Puede formatearse en modo VR o modo de video Modo de video 480 minutos Tiempo máximo de (12 centímetros) grabación 144 minutos (8 centímetros) Modo VR 480 minutos (12 centímetros) 144 minutos (8 centímetros) 480 minutos (12 centímetros) 144 minutos (8 centímetros) Versione 2.0 Versione 2.0/4× Versione 2.0/8× Versione 2.0/16× Versione 1.1,1.2 Versiones grabables/ Versione 1.
Introduction ESPAÑOL Conexión a un Sintonizador Externo 1) Desconecte el cable de alimentación de su televisor del tomacorriente de CA. 2) Efectúe la conexión como se ilustra abajo. Connections parte trasera de su televisor ej.) cable coaxial de RF VIDEO IN señal de TV AUDIO IN R L ANT.
ESPAÑOL Configuración Inicial Cuando usted encienda este aparato por primera vez necesita seguir estos pasos. 1 2 Presione [POWER]. Encienda el televisor. Seleccione la entrada a la cual está conectado el aparato. Utilice [K / L] para seleccionar su idioma deseado, y luego presione [ENTER] para establecerlo. Initial Setting Grabación Básica 1 Presione [OPEN/CLOSE A] para abrir la bandeja de discos e insertar su disco con el rótulo aupntando hacia arriba.
Introduction ESPAÑOL Grabación con Temporizador .@/: TIMER PROG. ABC DEF INPUT SELECT 1 JKL MNO AUDIO PQRS TUV WXYZ REPEAT SPACE CLEAR SETUP RETURN ENTER DISPLAY LUN ENE/01 11:00AM Fcha 3 4 5 Empieza Termina Prog. nuevo L1/L2 Configure una programación del temporizador. Presione [ENTER]. Presione [POWER] para configurar una programación del temporizador. Aparecerá en el pantalla del panel frontal. Configure la fecha.
LIMITED WARRANTY FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows: DURATION: PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Certain parts are excluded from this warranty. LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.