INTRODUCTION Owner's Manual INITIAL SETTING LD200SL8 CONNECTION 20" Digital / Analog LCD TV built-in DVD Player WATCHING TV OPTIONAL SETTING OPERATING DVD DVD SETTING TROUBLESHOOTING IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429, OR VISIT OUR WEB SITE AT http://www.SylvaniaConsumerElectronics.com © 2007 Funai Electric Co., Ltd. INFORMATION TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA.
INTRODUCTION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
INTRODUCTION 5 Precautions LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW. POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND. FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the manual.
INTRODUCTION LOCATION For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. • Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.
INTRODUCTION 5 Contents INTRODUCTION DVD Functions TV Functions INITIAL SETTING WATCHING TV OPTIONAL SETTING TROUBLESHOOTING Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 INFORMATION Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 5 Features TV • DTV/TV/CATV - You can use your remote control to select channels which are broadcast in digital, conventional analog, standard definition. Also, cable subscribers can access their cable TV channels. • Program Information Display (DTV only) - You can display the title, contents and other information of the current DTV program on the TV screen. • Auto Channel Scan - This unit automatically scans and memorizes channels available in your area, eliminating difficult setup procedures.
INTRODUCTION 5 Remote Control Function 12 13 14 15 1 2 3 16 17 18 5 19 20 6 21 8 3. 4. 10 11 24 25 Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control. 2 3 INFORMATION 1 TROUBLESHOOTING 5 Installing the Batteries DVD SETTING POWER button (p13) Press to turn the unit on and off. MUTE button (p16) Press to turn the sound on and off. SLEEP button (p19) Press to activate the sleep timer.
INTRODUCTION 5 Control Panel 1 2 3 4 5 6 7 8 SETUP STOP PLAY EJECT VOLUME CHANNEL INPUT POWER DVD 9 10 1. SETUP button (p14 / p38) Press to display the main menu. 2. STOP C button (p28) Press to stop disc playback. 3. PLAY B button (p28) Press to begin disc playback. 4. EJECT A button (p28) Press to eject the disc. 5. VOLUME X / Y buttons (p16) Press to adjust the volume. 6. CHANNEL K/L buttons (p16) Press to select channels or move up/down through the main menu items. 7.
INTRODUCTION 5 Attaching a Wall Mount Bracket (sold separately) CONNECTION The following is a description of the method for attaching a wall mount to this unit. When performing this operation, refer to the instruction manual included with the wall mount kit. You need the following wall mount kit for this unit. Vision Mount LCD Mounts / model number: VMFb For more information, please visit CSAV website at www.csavinc.
CONNECTION Cables not included. Please purchase the necessary cables at your local store. 5 Basic Connection This section describes how to connect the unit to an antenna, cable/satellite box, etc. Note: • Be sure your antenna or other device is connected properly before plugging in the power cord. [Antenna Cable Connection] When connecting the unit to an antenna or cable TV company (without cable/satellite box) Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit. e.g.
INTRODUCTION Cables not included. Please purchase the necessary cables at your local store. CONNECTION 5 External Device Connection INITIAL SETTING [Component Video Cable Connection] Component video connection offers better picture quality for video devices connected to the unit. Use a component video cable to connect the unit to external video devices equipped with component video output jacks.
CONNECTION Cables not included. Please purchase the necessary cables at your local store. [Video Connection] Video connection offers standard picture quality for video devices connected to the unit. If you connect to the unit’s video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO1. When the audio jack of the video device is monaural, connect the RCA audio cable to the audio L input jack. e.g.
These operations are accessible by remote control. Some may also be accessible by controls on the main unit. 5 Initial Setup Note: Before you begin: Make sure if the unit is connected to antenna or cable. [POWER] to turn on the unit. • This operation may take a few moments. from the choices on the right side of the TV screen.
INITIAL SETTING 5 Main Menu 5 Auto Channel Scan This section describes the overview of the main menu displayed when you press [SETUP]. For more details, see the reference page for each item. The main menu consists of the function setting items below. If you switch wires (e.g., between antenna and CATV) or if you move the unit to a different area after the initial setting, or if you restore the DTV channel you deleted, you will need to perform auto channel scan.
5 Language Selection You can choose English, Spanish, or French as your on-screen language. 1 Press [SETUP] to display the main menu. CONNECTION INITIAL SETTING • If you connect the cable system directly, contact the CATV installer. • If you press [POWER] or [SETUP] during auto channel scan, the setting will be canceled. • When no channel can be received by auto channel scan, “NO TV SIGNALS” will be displayed on the TV screen. • Channel settings will be saved even if the power fails.
WATCHING TV 5 Channel Selection 5 Volume Adjustment Select channels by using [CH. K/L] or [the Number buttons]. This section describes how to adjust the volume. The mute function, which turns the sound off and on, is also described. • To select the memorized channels, use [CH. K/L] or [the Number buttons]. • To select the non-memorized channels, use [the Number buttons]. Use [VOL. X/Y] to adjust the audio volume.
INTRODUCTION 5 MTS System You can easily switch with the remote control to the DTV (ATSC) and TV (NTSC) or to access an external device when they are connected to the unit. MTS (multichannel television sound) system is the method of encoding 3 additional channels of audio into an NTSC-format audio carrier. This section describes how to switch the audio in the analog mode and how to switch the audio language in the digital mode.
WATCHING TV 5 Screen Information You can display the currently selected channel or other information such as the audio mode on the TV screen. DTV TV In the analog mode, the current channel number is displayed. Press [DISPLAY]. In the digital mode, the detailed broadcasting information for the current channel such as program title, program guides are displayed. Press [DISPLAY] repeatedly to cycle through the available display modes.
DTV Press [SCREEN MODE] repeatedly to switch the TV aspect ratio. 5 Sleep Timer The sleep timer can be set to automatically turn off the unit after an incremental period of time. CONNECTION 2 types of display modes can be selected in the digital mode when the broadcasting station is sending 16:9 video signal. INTRODUCTION 5 TV Screen Display Mode 1 Press [SLEEP] to set the sleep timer. INITIAL SETTING SLEEP OFF • Sleep timer display appears on the TV screen.
OPTIONAL SETTING 5 Channel Add/Delete Note: The channel add/delete function lets you add the channel that was not added by the auto channel scan due to the reception status at the initial setting. You can also delete the unnecessary channels. 1 Press [SETUP] to display the main menu. 2 Use [Cursor K/L] to select “CHANNEL SETUP”, then • ”ADD/DELETE(DTV)” or “ADD/DELETE” menu will disappear automatically in about 10 seconds.
INTRODUCTION 5 Closed Caption 3 Press [SETUP] to exit. TV 1 Press [SETUP] to display the main menu. [ENTER] repeatedly to change the setting. e.g.) digital TV mode or [ENGLISH] [OFF] [BRIGHT] [NORMAL] [CAPTION1] OPTIONAL SETTING [OFF] • To show the closed caption on your TV screen, broadcast signal must contain the closed caption data. • Not all TV programs and commercials have the closed caption or all types of the closed caption. • Captions and texts may not match the TV voice exactly.
OPTIONAL SETTING 5 DTVCC Style 5 DTV Closed Caption DTV DTV In addition to the basic closed caption described on page 21, DTV has its own closed caption called DTVCC. Use this menu to change the settings for DTVCC. You can change the style of DTV CC such as font, color or size, etc. 1 Press [SETUP] to display the main menu. 1 2 Use [Cursor K /L] to select “DTVCC“, then press 2 Use [Cursor K /L] to select “DTVCC“, then press [ENTER]. Press [SETUP] to display the main menu. [ENTER]. e.g.
INTRODUCTION 5 Back Light Setting You can set the desired brightness mode. CONNECTION 1 Press [SETUP] to display the main menu. • CAPTION SIZE Closed captioning font size can be changed as below. • CHARACTER EDGE Edge type of the displayed caption can be switched as below. 2 Use [Cursor K /L] to select “BACK LIGHT”, then press [ENTER] repeatedly to change the setting. e.g.
OPTIONAL SETTING 5 Color Temperature 5 V-chip You can adjust color temperature of the TV screen. V-chip reads the ratings for programs, then denies access to the programs which exceed the rating level you set. With this function, you can block certain programming inappropriate for children. 1 Press [SETUP] to display the main menu. 1 Press [SETUP] to display the main menu. 2 Use [Cursor K /L] to select “COLOR TEMP.
INTRODUCTION A. TV Rating [ENTER]. e.g.) digital TV mode - V - CHIP SETUP TV RATING MPAA RATING DOWNLOADABLE RATING CHANGE PASSWORD [To Set the Sub Ratings] As for TV-Y7, TV-PG, TV-14 or TV-MA, you can further set the sub ratings to block specific elements of programming. To set the sub ratings, follow the steps below. 1 Use [Cursor K /L ] to select the desired main rating, then press [ENTER] twice to show its sub ratings.
OPTIONAL SETTING C. Change Password B. MPAA Rating MPAA Rating is the rating system created by MPAA (Motion Picture Association of America). Although the default code “0000” is supplied with the unit, you can set your own password. 4 Use [Cursor K /L] to select “MPAA RATING”, then press 4 Use [Cursor K /L] to select “CHANGE PASSWORD”, then [ENTER]. press [ENTER]. e.g.) digital TV mode e.g.
INTRODUCTION OPERATING DVD DVD Functions 5 Playable Media Mark (logo) DVD-video *1, 2, 4, 6, 10, 11 Region code 1 Recorded signals Media size CONNECTION Type of media Disc types or ALL DVD+RW DVD+R * 1, 4, 5, 6, 9, 10 - audio CD * 4, 6, 10 - e. g.) digital video (MPEG2) title 1 title 2 chapter 1 chapter 2 chapter 3 chapter 4 chapter 1 chapter 2 WATCHING TV - INITIAL SETTING DVD-RW DVD-R * 1, 3, 4, 5, 6, 7, 8, 9, 10 5 inches (12 cm) audio CD e. g.
OPERATING DVD These operations are accessible by remote control. Some may also be accessible by controls on the main unit. 5 Playback Before you begin: Turn on the amplifier and any other equipment which is connected to this unit. Make sure the external audio receiver are set to the correct input mode. 1 Press [POWER] to turn on the unit. Note: • “ ” may appear at the top-right on the TV screen when the operation is prohibited by the disc or this unit.
INTRODUCTION 5 Step-by-step Playback 5 Zoom DVD DVD CONNECTION The zoom function allows you to enlarge the video image and to pan through the enlarged image. Each time you press [PAUSE F] in the pause mode, the disc goes forward one frame at a time. 1 During playback, press [MODE] repeatedly until “ To continue playback, press [PLAY B]. ” appears. 1.3 × (ZOOM) INITIAL SETTING Note: • Set “STILL MODE” to “FIELD” in “DISPLAY“ menu if pictures in the pause mode are blurred. (Refer to page 39.
OPERATING DVD 5 MP3 Playback MP3 MP3 is a method of compressing files. You can copy MP3 files on CD-RW/-R from the personal computer and play the files on this unit. 1 Insert an CD-RW/-R with MP3 files, playback starts automatically. • Press [PLAY B] if the disc is already inserted. • Press [MENU] when you want to call up the file list. When selecting the folder: • Press [Cursor B] when you want to go to the next hierarchy.
INTRODUCTION 5 Search Functions Chapter / Title Search CD MP3 Using [MODE] Using [MODE] playback, press [MODE] repeatedly until 1 During “ “ appears. 1 During playback, press [MODE] repeatedly until “ “ appears. _ _ /29 (SEARCH) INITIAL SETTING • If you want to perform the title search, press [Cursor K / L] repeatedly until “ “ appears. CONNECTION DVD Track Search _ _ /12 (SEARCH) 2 Press [the Number buttons] to select your desired track within 60 seconds.
OPERATING DVD 5 Repeat Playback Time Search DVD You can repeat playback chapters, titles or tracks/files on a disc. CD 1 During playback, press [MODE] repeatedly until “ “/“ playback, press [MODE] repeatedly until 1 During “ “ appears. “ appears. OFF (REPEAT) e.g.) DVD 2 Press [Cursor K / L] to change the repeat mode. _ _ /12 (SEARCH) DVD 2 Use [Cursor K / L] repeatedly until “ or TOTAL “ appears.
INTRODUCTION Note: Note: MP3 You may determine the order in which tracks/files will be played back. 1 In stop mode, press [MODE] repeatedly until the “PROGRAM” menu appears. PROGRAM CD-DA ENTER PLAY CLEAR T T T T T T T 1 2 3 4 5 6 7 TOTAL 0:00:00 3:31 4:28 4:19 3:58 4:12 4:02 3:55 1/ 3 1/ 1 T 1 3:31 press [ENTER] to store. • Additional tracks/files may be on other screens. Use [Cursor K/ L] to go on to the next / previous pages.
OPERATING DVD 5 On-screen Display CD You can check the information about the current disc by pressing [DISPLAY] on the remote control.
INTRODUCTION 5 Special Settings Subtitle Language This unit allows you to select a subtitle language (if available) during DVD playback. 1 During playback, press [MODE] repeatedly until “ appears. CONNECTION DVD DVD “ Audio Language This unit allows you to select an audio language (if multiple languages are available) during DVD playback. During playback, press [AUDIO] repeatedly until the desired language appears. INITIAL SETTING 1.ENG Dolby D 3/2.
OPERATING DVD Virtual Surround Black Level Setting You can enjoy virtual surround on your existing 2 channel stereo system. DVD Adjust the black level to make the dark areas of the TV picture brighter. 1 During playback, press [MODE] repeatedly until “ “ appears. 1 During playback, press [MODE] repeatedly until “ “ appears. OFF (BLACK LEVEL) 2 Use [Cursor K / L] to adjust the black level. or ON (BLACK LEVEL) ON : Makes the dark areas brighter. OFF : Shows the original picture as recorded.
INTRODUCTION Marker Setup This feature allows you to assign a specific point on a disc to be called back later. CD To set a marker To return to the marker later 1 During playback, press [MODE] repeatedly until 1 To select a desired marker, repeat steps 1 to 3 in “ CONNECTION DVD ”/“ ” appears. “To set a marker“. e.g.) DVD INITIAL SETTING e.g.) DVD _ _ /12 (SEARCH) or 2 Use [Cursor K /L] repeatedly until marker search menu 2 Press [ENTER] at the desired marker to start playback appears.
DVD SETTING Settings are only effective when the unit is in DVD mode and any discs should not be played back. QUICK MENU AT A GLANCE If you make setting for “TV MODE“ or “DOLBY DIGITAL”, you can also enter from the “QUICK“ menu. Use [Cursor K /L] to select “QUICK” and press [ENTER] at step 3. SETUP [ENTER]. [AUDIO] *1, *2 (Default: ORIGINAL) Select the desired audio language.
You can change the TV aspect ratio and still mode clarity in “DISPLAY” menu. [ENTER]. CONNECTION 1 In stop mode, press [SETUP] to display “TV SETUP”. 6 Use [Cursor K /L] to select the desired item, then press [TV MODE] (Default: 4:3 LETTER BOX) Select the desired TV aspect ratio. --- TV SETUP --LANGUAGE BACK LIGHT COLOR TEMP.
DVD SETTING 5 DVD Audio Setting Choose the appropriate audio settings for your equipment. It only affects during the playback of DVD. 1 In stop mode, press [SETUP] to display “TV SETUP”. --- TV SETUP --LANGUAGE BACK LIGHT COLOR TEMP. DVD SETUP [ENGLISH] [BRIGHT] [NORMAL] 6 Use [Cursor K /L] to select the desired item, then press [ENTER]. [DRC] (Default: ON) Sets the dynamic range control. This function is available only on the discs which are recorded in the Dolby Digital format.
Parental setting prevents your children from viewing inappropriate materials. (password protected.) Playback will stop if the ratings exceed the levels you set. 7 Use [Cursor K /L] to select the desired item, then press [ENTER]. LANGUAGE BACK LIGHT COLOR TEMP.
DVD SETTING 5 Others 6 Use [Cursor K /L] to select the desired item, then press You can change the other functions. 1 In stop mode, press [SETUP] to display “TV SETUP”. --- TV SETUP --LANGUAGE BACK LIGHT COLOR TEMP. DVD SETUP [ENGLISH] [BRIGHT] [NORMAL] [ENTER]. [ANGLE ICON] (Default: ON) Set to “ON” to show the angle icon when multiple camera angles are available during DVD playback. SETUP or OTHERS ANGLE ICON SCREEN SAVER ON OFF 2 Use [Cursor K /L] to select “DVD SETUP”, then press [ENTER].
5 Language Code List You can reset all the settings except for the parental setting and on-screen menu language. Language --- TV SETUP --LANGUAGE BACK LIGHT COLOR TEMP. DVD SETUP [ENGLISH] [BRIGHT] [NORMAL] [ENTER]. --- TV SETUP --LANGUAGE BACK LIGHT COLOR TEMP. DVD SETUP [ENGLISH] [BRIGHT] [NORMAL] [ENTER]. SETUP or SELECT:K/L EXIT:SETUP SET:ENTER CANCEL:RETURN 4 Use [Cursor K /L] to select “YES”, then press [ENTER].
TROUBLESHOOTING 5 Troubleshooting Guide If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart once before calling for service. Symptom Remedy No power • Be sure the power cord is plugged in. • If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to reset itself. No picture or sound • Check if the power is on. • Check the outlet connection. • Check the antenna or cable connection to the main unit.
INTRODUCTION • Many digital channels have alternate channel numbers. The unit changes the numbers automatically to the ones signifying the broadcasting stations. These are the numbers used for analog broadcasts. Remote control does not work • Check the antenna or cable connection to the main unit. • Check the batteries of the remote control. • Check if there is an obstacle between the infrared sensor window and the remote control. • Test the signal output. If OK, then possible remote sensor trouble.
INFORMATION 5 Glossary ATSC Dolby Digital Region Code Acronym that stands for Advanced Television Systems Committee and the name of the digital broadcasting standards. The system developed by Dolby Laboratories to compress digital sound. It offers stereo sound (2ch) or multi-channel audio. Aspect ratio EDTV (enhanced definition TV) The width of a TV screen relative to its height.
INTRODUCTION 5 Cable Channel Designations CATV channel TV Display CATV channel TV Display CATV channel TV Display CATV channel TV Display CATV channel TV Display CATV channel TV Display 2 2 J 23 W+8 44 W+29 65 W+50 86 W+66 107 W+87 128 3 3 K 24 W+9 45 W+30 66 W+51 87 W+67 108 W+88 129 4 4 L 25 W+10 46 W+31 67 W+52 88 W+68 109 W+89 130 5 5 M 26 W+11 47 W+32 68 W+53 89 W+69 110 W+90 131 6 6 N 27 W+12 48 W+33 69 W+54 90 W+70 111 W+91 132 7 7 O 28 W+13 49 W+34 70 W+55 91 W+71 112 W+92 133 8 8 P 29 W+1
LIMITED WARRANTY FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows: DURATION: PARTS: LABOR: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Certain parts and LCD image burn-in are excluded from this warranty. FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.
INTRODUCCIÓN Manual del Usuario AJUSTE INICIAL LD200SL8 CONEXIÓN Televisor Digital/Analógico con Pantalla LCD de 20" y Reproductor DVD Incorporado PARA VER LA TELEVISIÓN AJUSTE OPCIONAL UTILIZACIÓN DEL DVD AJUSTE DE DVD Discos de 5 pulgadas solamente SOLUCIÓN DE PROBLEMAS SI NECESITA AYUDA ADICIONAL CON LA INSTALACIÓN O CON EL FUNCIONAMIENTO DESPUÉS DE LEER EL MANUAL DEL USUARIO, LLAME AL TELÉFONO GRATUITO 1-800-968-3429, O VISITE NUESTRO SITIO WEB EN http://www.SylvaniaConsumerElectronics.
INTRODUCCIÓN ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO O DESCARGA ELÉCTRICA, NO EXPONGA ESTE APARATO A LLUVIA O HUMEDAD. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CUIDADO: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PLACA TRASERA). EL INTERIOR DE ESTE APARATO NO CONTIENE PIEZAS REPARABLES POR EL USUARIO. DEJE LA REPARACIÓN EN MANOS DE PERSONAL DE SERVICIO TÉCNICO CUALIFICADO.
INTRODUCCIÓN 5 Precauciones LA LÁMPARA DE LA PANTALLA LCD CONTIENE MERCURIO. SE DEBE TIRARLA DE ACUERDO A LA NORMATIVA LOCAL O LA LEY FEDERAL. PARA EVITAR LA DESCARGA ELÉCTRICA, HAGA COINCIDIR EL CONTACTO ANCHO DEL ENCHUFE CON LA RANURA ANCHA E INSERTE FIRMEMENTE. CONEXIÓN CUIDADO: ADVERTENCIA DE LA FCC Este equipo puede generar o utilizar energía de radiofrecuencia.
INTRODUCCIÓN UBICACIÓN Para un funcionamiento seguro y un rendimiento satisfactorio del aparato, tenga en cuenta lo siguiente a la hora de seleccionar un lugar para su instalación: • Debe protegerlo de la luz solar directa y mantenerlo apartado de fuentes de calor intenso. • Evite lugares polvorientos o húmedos. • Evite lugares con ventilación insuficiente para una disipación de calor adecuada. No bloquee los orificios de ventilación situados en la parte superior e inferior del aparato.
INTRODUCCIÓN 5 Contenido INTRODUCCIÓN Funciones del TV AJUSTE INICIAL Selección de Canal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Ajuste de Volumen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Para Cambiar entre Cada Modo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Sistema MTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCCIÓN 5 Características TV • DTV/TV/CATV - Puede utilizar su mando a distancia para seleccionar canales emitidos en formato digital, analógico convencional y definición estándar. Además, los suscriptores de cable pueden acceder a sus canales de televisión por cable. • Pantalla de Información de Programas (solamente DTV) - Puede visualizar el título, el contenido y otra información del actual programa DTV en la pantalla del televisor.
INTRODUCCIÓN 5 Función de Mando a distancia Distancia 5. 1 2 3 6. 7. 16 4 17 19 20 6 21 8 9 22 23 10 11 24 25 8. 9. 10. 1. 3. 4. 19. 20. 21. 22. 23 24. 25. Instale las pilas (AA x 2) de manera que coincida la polaridad indicada en el interior del compartimento de las pilas del mando a distancia. 1 2 3 SOLUCIÓN DE PROBLEMAS 13. 18. AJUSTE DE DVD 5 Instalación de las Pilas 12. 17. UTILIZACIÓN DEL DVD 2. Botón POWER (p13) Presione para activar y desactivar la unidad.
INTRODUCCIÓN 5 Panel de Control 1 2 3 4 5 6 7 8 SETUP STOP PLAY EJECT VOLUME CHANNEL INPUT POWER DVD 9 10 1. Botón SETUP (p14 / p38) Presione para visualizar el menú principal. 2. Botón STOP C (p28) Presione para detener la reproducción del disco. 3. Botón PLAY B (p28) Presione para comenzar la reproducción del disco. 4. Botón EJECT A (p28) Presione para expulsar el disco. 5. Botón VOLUME X / Y (p16) Presione para ajustar el volumen. 6.
CONEXIÓN A continuación se ofrece una descripción del método para instalar un soporte para el montaje en pared en este aparato. Al realizar esta operación, consulte el manual de instrucciones incluido con el juego de montaje en pared. Necesitará el siguiente soporte de montaje en pared para este aparato. Soporte Vision Mount LCD/número de modelo: VMFb Para más información, visite el sitio web de CSAV en www.csavinc.
CONEXIÓN Cables No Incluidos. Deberá adquirir los cables necesarios en su establecimiento local. 5 Conexión Básica En esta sección se describe cómo conectar el aparato a una antena, caja de cable/satélite, etc. Nota: • Asegúrese de que su antena u otra dispositivo está conectada correctamente antes de enchufar el cable de alimentación.
INTRODUCCIÓN Cables No Incluidos. Deberá adquirir los cables necesarios en su establecimiento local. (verde) (azul) PARA VER LA TELEVISIÓN cable de vídeo en componentes (rojo) p. ej.
CONEXIÓN Cables No Incluidos. Deberá adquirir los cables necesarios en su establecimiento local. [Conexión de Vídeo] La conexión de vídeo ofrece una calidad normal de imagen para dispositivos de vídeo conectados al aparato. Si se conecta a la toma de entrada de vídeo del aparato, conecte cables RCA de audio a las tomas de audio L/R (izquierda/derecha) de VIDEO1. Cuando la toma de audio del dispositivo de vídeo sea monoaural, conecte el cable RCA de audio a la toma de entrada de audio L (izquierda). p. ej.
INTRODUCCIÓN AJUSTE INICIAL Se puede acceder a estas operaciones mediante el mando a distancia. Algunas también pueden ser accesibles mediante los mandos del aparato principal. Nota: Esta sección le guiará a través del ajuste inicial del aparato, que incluye la selección de un idioma para sus menús de pantalla y “PREA. AUTO CA.”, que explora y memoriza automáticamente los canales visibles. Antes de empezar: Asegúrese de que el aparato está conectada a la antena o al cable.
AJUSTE INICIAL 5 Menú Principal 5 Exploración Automática de Canales En esta sección se describen los aspectos generales del menú principal que aparece al presionar [SETUP]. Para más detalles, consulte la página de referencia de cada elemento. El menú principal se compone de los siguientes elementos de ajuste de función.
5 Selección de Idioma Puede elegir INGLÉS, ESPAÑOL o FRANCÉS como idioma de pantalla. 1 Presione [SETUP] para visualizar el menú principal. CONEXIÓN 2 Utilice [Cursor K /L] para seleccionar “IDIOMA”, y luego presione [ENTER] repetidamente para cambiar el ajuste. p. ej.) modo TV digital AJUSTE DE CANAL AJUSTE DE V-CHIP IDIOMA TITULO LUZ DE FONDO TENPE.
PARA VER LA TELEVISIÓN 5 Selección de Canal 5 Ajuste de Volumen Seleccione los canales utilizando [CH. K/L] o [los botones numéricos]. En esta sección se describe cómo ajustar el volumen. También se describe la función de silenciamiento, que activa y desactiva el sonido. • Para seleccionar los canales memorizados, utilice [CH. K/L] o [los botones numéricos]. • Para seleccionar los canal es no memorizados, utilice [los botones numéricos]. Utilice [VOL. X/Y] para ajustar el volumen de audio.
INTRODUCCIÓN 5 Sistema MTS Puede cambiar fácilmente entre DTV (ATSC) y TV (NTSC) o acceder a un dispositivo externo con el mando a distancia cuando estén conectados al aparato. El sistema MTS (sonido de televisión multicanal) es el método de codificación de 3 canales adicionales de audio en un soporte de audio de formato NTSC. En esta sección se describe cómo cambiar el audio en el modo analógico y cómo cambiar el idioma de audio en el modo digital.
PARA VER LA TELEVISIÓN 5 Información de Pantalla Puede visualizar el canal actualmente seleccionado u otra información, por ejemplo el modo de audio, en la pantalla del televisor. DTV TV En el modo analógico se visualiza el número del canal actual. En el modo digital se visualiza la información de emisión detallada para el canal actual como, por ejemplo, el título del programa y las guías de programas. Presione [DISPLAY] repetidamente para recorrer los modos de visualización disponibles.
DTV INTRODUCCIÓN 5 Modo de Visualización de Pantalla del Televisor 5 Temporizador de Apagado El temporizador de apagado puede configurarse para apagar automáticamente el aparato después de un periodo incremental de tiempo. Presione [SCREEN MODE] repetidamente para cambiar la relación del aspecto del televisor. CONEXIÓN En el modo digital pueden seleccionarse 2 tipos de modos de visualización cuando la emisora envíe una señal 16:9. 1 Presione [SLEEP] para ajustar el temporizador de apagado.
AJUSTE OPCIONAL 5 Agregar/Borrar Canales Nota: La función de agregar/borrar canales le permite agregar el canal que no se haya agregar mediante la exploración automática de canales debido al estado de la recepción en el ajuste inicial. También puede eliminar los canales innecesarios. 1 Presione [SETUP] para visualizar el menú principal. • El menú “AGREGAR/BORRAR (DTV)” o “AGREGAR/BORRAR“ desaparecerá automáticamente en unos 10 segundos.
INTRODUCCIÓN 5 Subtítulos Cerrados TV CONEXIÓN Puede ver los subtítulos cerrados (cc) para programas de televisión, películas e informativos. Subtítulo cerrado se refiere al texto de diálogo o descripciones visualizadas en pantalla para personas con problemas auditivos. 3 Presione [SETUP] para salir. 2 Utilice [Cursor K /L] para seleccionar “TITULO”, y luego Nota: p. ej.
AJUSTE OPCIONAL 5 Subtítulos Cerrados en DTV 5 Estilo DTVCC DTV DTV Además de los subtítulos cerrados básicos descritos en la página 21, DTV tiene sus propios subtítulos cerrados denominados DTVCC. Utilice este menú para cambiar la configuración de DTVCC. Puede cambiar el estilo de DTV CC, por ejemplo fuente, color o tamaño, etc. 1 Presione [SETUP] para visualizar el menú principal. 1 Presione [SETUP] para visualizar el menú principal.
INTRODUCCIÓN 5 Ajuste de Luz de Fondo Puede ajustar el modo de brillo deseado. CONEXIÓN 1 Presione [SETUP] para visualizar el menú principal. • TAMAÑO TITULO El tamaño de fuente de los subtítulos cerrados puede elegirse entre los siguientes: • COLOR ADELANTE, COLOR FONDO El color de fuente y de fondo del subtítulo mostrado puede elegirse entre los siguientes: y luego presione [ENTER] repetidamente para cambiar el ajuste. p. ej.
AJUSTE OPCIONAL 5 Temperatura de Color 5 V-chip Puede ajustar la temperatura de color de la pantalla del televisor. V-chip lee las clases de los programas, y niega el acceso a los programas que exceden el nivel de clasificación establecido. Con esta función, puede bloquear determinados programas inapropiados para niños. 1 Presione [SETUP] para visualizar el menú principal. 1 Presione [SETUP] para visualizar el menú principal. 2 Utilice [Cursor K /L] para seleccionar “TENPE.
INTRODUCCIÓN A. Clase de TV luego presione [ENTER]. p. ej.) modo TV digital - AJUSTE DE V-CHIP CLASE DE TV CLASE DE MPAA CLASE DESCARGADA CAMBIAR CÓDIGO 1 Utilice [Cursor K /L ] para seleccionar la clasificación principal deseada y luego presione [ENTER] dos veces para mostrar sus subcategorías. 5 TV-Y TV-Y7 ( ) TV-G TV-PG (DLSV) TV-14 (DLSV) TV-MA ( LSV) [MIRAR] ) [MIRAR] [MIRAR] ) [MIRAR] ) [MIRAR] ) [MIRAR] 2 Utilice [Cursor K /L ] y luego presione [ENTER] repetidamente para cambiar el ajuste.
AJUSTE OPCIONAL C. Cambiar Contraseña B. Clase de MPAA Clase de MPAA es el sistema de clasificación creado por la MPAA (Motion Picture Association of America). Aunque el código predeterminado “0000” viene incorporado con el aparato, usted puede ajustar su propia contraseña. 4 Utilice [Cursor K /L] para seleccionar “CLASE DE MPAA” 4 Utilice [Cursor K /L] para seleccionar “CAMBIAR y luego presione [ENTER]. CÓDIGO” y luego presione [ENTER]. p. ej.) modo TV digital p. ej.
INTRODUCCIÓN UTILIZACIÓN DEL DVD Funciones del DVD 5 Medios que se Pueden Reproducir DVD-video *1, 2, 4, 6, 10, 11 Marca (logotipo) Código regional 1 Señales grabadas Tamaño de los medios CONEXIÓN Tipo de medios Tipo de discos o ALL DVD+RW DVD+R * 1, 4, 5, 6, 9, 10 - CD de audio * 4, 6, 10 - p. ej.
UTILIZACIÓN DEL DVD Se puede acceder a estas operaciones mediante el mando a distancia. Algunas también pueden ser accesibles mediante los mandos del aparato principal. 5 Reproducción Antes de empezar: Encienda el amplificador y cualquier otro equipo que esté conectado a esta unidad. Asegúrese de que el receptor de audio externo está ajustado en el modo de entrada correcto. 1 Presione [POWER] para encender el aparato.
INTRODUCCIÓN 5 Reproducción Paso a Paso 5 Zoom DVD DVD CONEXIÓN La función del zoom le permite ampliar la imagen y moverse en sentido horizontal por la imagen ampliada. Cada vez que presiona [PAUSE F] en el modo de pausa, el disco avanza un cuadro cada vez. 1 Durante la reproducción, presione repetidamente Para continuar con la reproducción, presione [PLAY B]. [MODE] hasta que aparezca “ ”. 1.
UTILIZACIÓN DEL DVD 5 Reproducción MP3 MP3 MP3 es un método de compresión de archivos. Puede copiar archivos MP3 en discos CD-RW/-R desde la computadora personal y reproducir los archivos en esta unidad. 1 Inserte un CD-RW/-R con archivos MP3, y la reproducción comenzará automáticamente. • Presione [PLAY B] si ya hay un disco insertado. • Presione [MENU] cuando quiera llamar a la lista de archivos. Cuando seleccione la carpeta: • Presione [Cursor B] cuando quiera ir a la siguiente jerarquía.
INTRODUCCIÓN 5 Funciones de Búsqueda Búsqueda de Capítulos / Títulos Búsqueda de Pistas MP3 CD Utilizando [MODE] Utilizando [MODE] Presione repetidamente [MODE] durante la reproduc1 ción “. hasta que aparezca “ repetidamente [MODE] durante la reproduc1 Presione ción hasta que aparezca “ “. _ _ /29 (BÚSQUEDA) “. _ _ /12 (BÚSQUEDA) PARA VER LA TELEVISIÓN Presione [los botones numéricos] antes de que pasen 60 2 segundos para seleccionar el capítulo o el título deseado.
UTILIZACIÓN DEL DVD Búsqueda por Tiempo DVD 1 5 Repetición de Reproducción Puede repetir la reproducción de capítulos, títulos o pistas/archivos de un disco. CD Presione repetidamente [MODE] durante la repro“/“ “. ducción hasta que aparezca “ p. ej.) DVD repetidamente [MODE] durante la repro1 Presione ducción hasta que aparezca “ “. APDO. (REPETICIÓN) _ _ /12 (BÚSQUEDA) 2 Presione [Cursor K/ L] para cambiar el modo de repetición. DVD repetidamente [Cursor K / L] hasta que apa2 Utilice “.
INTRODUCCIÓN Nota: Nota: MP3 Puede determinar el orden de la reproducción de las pistas/archivos. 1 Presione repetidamente [MODE] en el modo de parada hasta que aparezca el menú “PROGRAMA”.
UTILIZACIÓN DEL DVD 5 Visualización en Pantalla CD Presionando [DISPLAY] en el mando a distancia puede verificar la información relacionada con el disco actual. DVD estado de reproducción actual aparece solamente cuando múltiples ángulos están disponibles en el DVD.
INTRODUCCIÓN 5 Ajustes Especiales Idioma de Subtítulos Idioma de Audio Esta unidad le permite seleccionar un idioma de subtítulos (si está disponible) durante la reproducción de DVD. 1 Presione repetidamente [MODE] durante la reproducción hasta que aparezca “ “. CONEXIÓN DVD DVD Esta unidad le permite seleccionar un idioma de audio (si se encuentran disponibles múltiples idiomas) durante la reproducción de DVD. 1.ENG Dolby D 3/2.1ch 48k/3 rezca su idioma deseado.
UTILIZACIÓN DEL DVD Ajuste del Nivel del Negro Surround Virtual En su sistema estéreo de 2 canales actual puede disfrutar surround virtual. DVD Ajuste el nivel del negro para hacer que las áreas oscuras de la imagen del televisor tengan más brillo. 1 Presione repetidamente [MODE] durante la reproducción hasta que aparezca “ “. 1 Presione repetidamente [MODE] durante la reproducción hasta que aparezca “ APDO. (NIVEL DEL NEGRO) 2 Utilice [Cursor K / L] para ajustar el nivel del negro. “. APDO.
INTRODUCCIÓN Puesta de Marcador Esta característica le permite poner un punto específico en un disco que será llamado posteriormente. CD CONEXIÓN DVD Para poner un marcador Para volver al marcador posteriormente 1 Presione repetidamente [MODE] durante la reproduc- 1 Para seleccionar un marcador deseado, repita los pasos _ _ /12 (BÚSQUEDA) 1-3 de “Para poner un marcador” explicados anteriormente. p. ej.) DVD o rezca el menú de búsqueda de marcador. o o • El marcador queda puesto ahora.
AJUSTE DE DVD Los ajustes sólo son eficaces cuando la unidad está en el modo DVD y no se reproduce ningún disco. MENÚ RÁPIDO A SIMPLE VISTA Si desea ajustar “MODO TV” o “DOLBY DIGITAL”, también lo puede hacer entrando desde el menú “RÁPIDO”. Utilice [Cursor K /L] para seleccionar “RÁPIDO” y luego presione [ENTER] en el paso 3. AJUSTE deseado y presione [ENTER]. [AUDIO] *1, *2 (Predeterminado: ORIGINAL) Seleccione el idioma de audio deseado.
INTRODUCCIÓN 5 Ajuste de la Pantalla Puede cambiar la relación de aspecto de la pantalla del televisor y la claridad del modo de imagen fija con el menú “PANTALLA”. “INSTALACIÓN TV”. --- INSTALACIÓN TV --- deseado y luego presione [ENTER]. [MODO TV] (Ajuste predeterminado: 4:3 LETTER BOX) Seleccione la relación de aspecto del televisor deseada. AJUSTE o 4:3 LETTER BOX 4:3 PAN & SCAN IDIOMA [ESPAÑOL] LUZ DE FONDO [BRILLO] TENPE.
AJUSTE DE DVD 5 Ajuste de Audio de DVD Elija el ajuste de audio apropiado para su equipo. Éste sólo se aplicará durante la reproducción de discos DVD. 1 Presione [SETUP] en el modo de parada para visualizar “INSTALACIÓN TV”. --- INSTALACIÓN TV --IDIOMA [ESPAÑOL] LUZ DE FONDO [BRILLO] TENPE. DE COLOR [NORMAL] INSTALACIÓN DVD 6 Utilice [Cursor K /L] para seleccionar el elemento deseado y luego presione [ENTER]. [DRC] (Ajuste predeterminado: ENC.) Ajusta el control de la gama dinámica.
INTRODUCCIÓN 5 Ajuste Paterno El ajuste paterno impide que sus hijos puedan ver programas que no sean apropiados para ellos. (Protección mediante contraseña.) La reproducción se detiene si la calificación excede los niveles que usted ha establecido. deseado y luego presione [ENTER]. AJUSTE o --- INSTALACIÓN TV --IDIOMA [ESPAÑOL] LUZ DE FONDO [BRILLO] TENPE. DE COLOR [NORMAL] INSTALACIÓN DVD --- INSTALACIÓN TV --IDIOMA [ESPAÑOL] LUZ DE FONDO [BRILLO] TENPE.
AJUSTE DE DVD 5 Otros Puede cambiar otras funciones. 1 Presione [SETUP] en el modo de parada para visualizar “INSTALACIÓN TV”. --- INSTALACIÓN TV --IDIOMA [ESPAÑOL] LUZ DE FONDO [BRILLO] TENPE. DE COLOR [NORMAL] INSTALACIÓN DVD 6 Utilice [Cursor K /L] para seleccionar el elemento deseado y luego presione [ENTER]. [ICONO DE ÁNGULO] (Ajuste predeterminado: ENC.) Póngalo en “ENC.
1 Presione [SETUP] en el modo de parada para visualizar “INSTALACIÓN TV”. --- INSTALACIÓN TV --- DVD” y luego presione [ENTER]. o --- INSTALACIÓN TV --IDIOMA [ESPAÑOL] LUZ DE FONDO [BRILLO] TENPE. DE COLOR [NORMAL] INSTALACIÓN DVD luego presione [ENTER]. RÁPIDO PERSNALIZ. INICIALIZAR SELECCIONAR:K/L SALIR:SETUP AJUSTAR:ENTER CANCELAR:RETURN presione [ENTER].
SOLUCIÓN DE PROBLEMAS 5 Guía de Solución de Problemas Si el aparato no funciona correctamente cuando se siguen las instrucciones de este manual del usuario, compruebe la siguiente tabla antes de llamar al servicio técnico. T Síntoma Solución No hay corriente • Asegúrese de que el cable de alimentación está enchufado. • Si se produce un corte de alimentación, desenchufe el cable de alimentación durante 30 minutos para permitir que el aparato se reinicie.
• Compruebe la conexión de antena o de cable con el aparato principal. • Compruebe las pilas del mando a distancia. • Compruebe si hay algún obstáculo entre el sensor y el mando a distancia. • Pruebe la salida de la señal. Si es correcta, es posible que haya algún problema con el sensor de infrarrojos. (Consulte “Comprobación de la señal de infrarrojos (IR)” en página 46.) • Con el mando a distancia, apunte directamente hacia la ventana del sensor de infrarrojos en la parte delantera del aparato.
INFORMACIÓN 5 Glosario ATSC Acrónimo de “Advanced Television Systems Committee” (Comité de sistemas avanzados de televisión) y el nombre de unas normas de emisión digital. Código de Región Las regiones asocian discos y reproductores con específicas regiones del mundo. Este aparato reproducirá únicamente discos que tengan códigos compatibles de región. Usted puede encontrar el código de región de su equipo mirando en el panel trasero.
INTRODUCCIÓN 5 Denominaciones de Canales de Cable Si se suscribe a la televisión por cable, los canales se muestran como 1-135. Las empresas de cable a menudo denominan los canales con letras o combinaciones de letra-número. Compruebe este detalle con su empresa local de cable. La tabla siguiente incluye las denominaciones de canal de cable habituales.
GARANTÍA LIMITADA FUNAI CORP. reparará este producto, de forma gratuita en Estados Unidos, en caso de defecto de materiales o fabricación, del modo siguiente: DURACIÓN: PIEZAS: FUNAI CORP. suministrará piezas de repuesto de las piezas defectuosas de forma gratuita durante un (1) año desde la fecha de compra minorista original. Determinadas piezas y el efecto de persistencia de la imagen en la pantalla LCD están excluidas de esta garantía. MANO DE OBRA: FUNAI CORP.