MC17/MC17A/ MC17T/MC17U QUICK REFERENCE GUIDE PRELIMINARY
MC17/MC17A/MC17T/MC17U Mobile Computer Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
Quick Reference Guide 3 Introduction This Quick Reference Guide explains how to install and charge the battery, scan bar codes, reset, maintain and troubleshoot the mobile computer. Unpacking Carefully remove all protective material from around the mobile computer and save the shipping container for later storage and shipping. Verify that you received all equipment listed below: • MC17 mobile computer • Lithium-ion battery (2400 mAh) • Quick Reference Guide. Inspect the equipment for damage.
MC17/MC17A/MC17T/MC17U Mobile Computer Scan Exit Window Access Cover Speaker Battery Cover Power Connector PRELIMINARY LED State Description Solid Red Scanner is enabled. Solid Green Bar code decode successful. Getting Started In order to start using the mobile computer you must install the battery and then charge it. Installing the Battery 1. Remove tape securing battery cover to handle. 2. Remove screw from screw hole (under tape). 3.
Quick Reference Guide 5 4. Ensure that the black rubber pad in the battery compartment is lying flat along the bottom of the compartment, with its smoother side facing up, and the rubber “fingers” straddling the screw boss. 5. Ensure the wire latch is in the up position. 6. Place the battery, rounded side down, in the compartment. Using a non-metallic tool (if necessary), guide the battery cable connector into the female battery connector on the mobile computer.
MC17/MC17A/MC17T/MC17U Mobile Computer 10. Inspect the position of the battery cover with the main housing. If the door is misaligned, remove battery and black rubber pad and re-install. Battery Door Properly Aligned 11. Secure the battery cover with the Torx screw using a T8 Torx drive. Torque the screw to 3.3 ±0.2 Kgf-cm (2.8 ±0.17 in-lb). PRELIMINARY 12. After installing a new battery, wait approximately one minute before inserting the mobile computer into a cradle.
Quick Reference Guide 7 3. The mobile computer starts to charge automatically. The mobile computer fully charges in approximately five hours. While charging, a red charging LED can be seen through the front panel of the cradle behind the mobile computer. Refer to the MC17 Product Reference Guide for specific charging profile information.
MC17/MC17A/MC17T/MC17U Mobile Computer 6. While holding the key down, lift the mobile computer out of the cradle. Scanning To scan bar codes: 1. Launch a scanning application. 2. Press the scan key and aim the mobile computer at a bar code. The LED turns red to indicate the scanner is on. 3. Adjust the aim so that the thin, red laser beam covers the entire length of the bar code. Correct Incorrect PRELIMINARY 012345 012345 4. If the decode is successful the LED turns green.
Quick Reference Guide 9 Resetting the Mobile Computer Warm Boot A warm boot restarts the mobile computer by closing all running programs. Press and simultaneously hold the Up Arrow and the Down Arrow keys for 10 seconds and then press the Scan key. Release the Up Arrow and the Down Arrow keys. Wait one second and then release the Scan key.
MC17/MC17A/MC17T/MC17U Mobile Computer 1. Place the mobile computer on a desktop with the display facing down. 2. Using a T6 Torx drive, remove two screws securing the bezel to the housing. 3. Align the replacement bezel on the housing. 4. Using a T6 Torx drive, secure the bezel to the housing using the two Torx screws. 5. Torque the screws to 2.5 ± 0.2 kgf-cm (2.17 ± 0.17 in-lbs.). Troubleshooting PRELIMINARY Problem Mobile computer does not turn on. Rechargeable battery did not charge.
Quick Reference Guide Problem Mobile computer shuts off. The mobile computer does not accept scan input. 11 Cause Solution Battery is depleted. Recharge the battery. Battery is not connected properly. Connect the battery properly. See Installing the Battery on page 4. The system is not responding. Warm boot the mobile computer. Scanning application is not loaded. Launch a scanning application on the mobile computer. See the system administrator. Unreadable bar code.
MC17/MC17A/MC17T/MC17U Mobile Computer All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following web site: http://www.zebra.com/support. Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user's authority to operate the equipment. CAUTION Only use Zebra approved and UL Listed accessories, battery packs and battery chargers.
Quick Reference Guide 13 Ad-hoc Operation (2.4 GHz band) Ad-Hoc operation is limited to Channels 1-11 (2412-2462 MHz). Frequency of Operation - IC 5 GHz Only The use in the UNII (Unlicensed National Information Infrastructure) band 1 5150-5250 MHz band is restricted to Indoor Use Only; any other use will make the operation of this device illegal. 2.4 GHz Only The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited by firmware.
MC17/MC17A/MC17T/MC17U Mobile Computer RF Exposure Guidelines Safety Information Reducing RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied. International The device complies with Internationally recognized standards covering human exposure to electromagnetic fields from radio devices.
Quick Reference Guide 15 Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure. Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful. Scanner Labeling COMPLIES WITH 21CFR1040.10 AND 1040.
MC17/MC17A/MC17T/MC17U Mobile Computer encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules.
Quick Reference Guide • 17 Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz Statement of Compliance Zebra, hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and 2011/65/EU. A Declaration of Conformity may be obtained from http://www.zebra.com/doc/.
MC17/MC17A/MC17T/MC17U Mobile Computer 經型式認證合格之低功率射頻電機，非經許可，公司、商號 或使用者均不得擅自變更頻率、加大功率或變更原設計之特 性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信； 經發現有干擾現象時，應立即停用，並改善至無干擾時方得 繼續使用。 前項合法通信，指依電信規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波 輻射性電機設備之干擾。 在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限 於室內使用。 Korea 당해 무선설비는 운용 중 전파혼신 가능성이 있음 당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 . Battery Information PRELIMINARY Zebra rechargeable battery packs are designed and constructed to the highest standards within the industry.
Quick Reference Guide 19 Battery Pack Information CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. This device is equipped with a removable and rechargeable Lithium polymer battery. When a replacement is needed, please request the dealer from whom your device was purchased to assist you. Use only manufacturer approved batteries.
MC17/MC17A/MC17T/MC17U Mobile Computer • • • • • Please follow local regulations to promptly dispose of used re-chargeable batteries. Do not dispose of batteries in fire. Seek medical advice immediately if a battery has been swallowed. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
Quick Reference Guide 21 Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.zebra.com/weee. Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.zebra.com/weee.
MC17/MC17A/MC17T/MC17U Mobile Computer Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/weee. Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο ∆ιαδίκτυο.
Quick Reference Guide PRELIMINARY 23
Service Information If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact Zebra Global Customer Support for your region. Contact information is available at: http://www.zebra.com/support. For the latest version of this guide go to: http://www.zebra.com/support PRELIMINARY Zebra Technologies Corporation Lincolnshire, IL U.S.A. http://www.zebra.
