User Manual

ManualsBrandsSymbol ManualsBarcode Scanning EquipmentBarcode Scanner

111

112

113

114

115

116

117

118

119

120

Table Of Contents

Symbol LS2208 Product Reference Guide
Warranty
Revision History
Table of Contents
About This Guide
- Introduction
- Chapter Descriptions
- Notational Conventions
- Related Documents
- Service Information
Getting Started
- Introduction
- Unpacking Your Scanner
- Setting Up the Scanner
Scanning
- Introduction
- Beeper Definitions
- LED Definitions
- Scanning in Hand-Held Mode
- Aiming
- Decode Zone
- Scanning in Hands-Free Mode
  - Assembling the Stand
  - Mounting the Stand (optional)
    - Screw Mount
    - Tape Mount
- Scanning in Hands-Free Mode
  - Scanning in the Hands-Free Mode
Maintenance and Technical Specifications
- Introduction
- Maintenance
- Troubleshooting
- Technical Specifications
- Scanner Signal Descriptions
User Preferences
- Introduction
- Scanning Sequence Examples
- Errors While Scanning
- User Preferences Default Parameters
- User Preferences
- Power Mode
  - Laser On Time
  - Beep After Good Decode
- Timeout Between Decodes
  - Timeout Between Decodes, Same Symbol
  - Timeout Between Decodes, Different Symbol
Keyboard Wedge Interface
- Introduction
- Connecting a Keyboard Wedge Interface
- Keyboard Wedge Default Parameters
- Keyboard Wedge Host Types
- ASCII Character Set
RS-232 Interface
- Introduction
- Connecting an RS-232 Interface
- RS-232 Default Parameters
- RS-232 Host Parameters
- ASCII Character Set
USB Interface
- Introduction
- Connecting a USB Interface
- USB Default Parameters
- USB Host Parameters
- ASCII Character Set
IBM 468X/469X Interface
- Introduction
- Connecting to an IBM 468X/469X Host
- IBM Default Parameters
- IBM 468X/469X Host Parameters
  - Port Address
  - Convert Unknown to Code 39
Wand Emulation Interface
- Introduction
- Connecting Using Wand Emulation
- Wand Emulation Default Parameters
- Wand Emulation Host Parameters
Undecoded Scanner Emulation Interface
- Introduction
- Connecting Using Undecoded Scanner Emulation
- Undecoded Scanner Emulation Default Parameters
- Undecoded Scanner Emulation Host
- Undecoded Scanner Emulation Host Parameters
123Scan2
- Introduction
- Communication with 123Scan2
- 123Scan2 Requirements
- Scanner SDK, Other Software Tools, and Videos
Symbologies
- Introduction
- Scanning Sequence Examples
- Errors While Scanning
- Symbology Default Parameters
- UPC/EAN
  - Enable/Disable UPC-A/ UPC-E
  - Enable/Disable UPC-E1
  - Enable/Disable EAN-13/EAN-8
  - Enable/Disable Bookland EAN
  - Decode UPC/EAN/JAN Supplementals
  - User-Programmable Supplementals
  - UPC/EAN/JAN Supplemental Redundancy
  - Transmit UPC-A/UPC-E/UPC-E1 Check Digit
  - UPC-A Preamble
  - UPC-E Preamble
  - UPC-E1 Preamble
  - Convert UPC-E to UPC-A
  - Convert UPC-E1 to UPC-A
  - EAN-8/JAN-8 Extend
  - Bookland ISBN Format
  - UPC/EAN Security Level
  - UCC Coupon Extended Code
- Code 128
  - Enable/Disable Code 128
  - Enable/Disable UCC/EAN-128
  - Enable/Disable ISBT 128
- Code 39
  - Enable/Disable Code 39
  - Enable/Disable Trioptic Code 39
  - Convert Code 39 to Code 32
  - Code 32 Prefix
  - Set Lengths for Code 39
  - Code 39 Check Digit Verification
  - Transmit Code 39 Check Digit
  - Code 39 Full ASCII Conversion
  - Code 39 Buffering (Scan & Store)
- Code 93
  - Enable/Disable Code 93
  - Set Lengths for Code 93
- Code 11
  - Code 11
  - Set Lengths for Code 11
  - Code 11 Check Digit Verification
  - Transmit Code 11 Check Digits
- Interleaved 2 of 5 (ITF)
  - Enable/Disable Interleaved 2 of 5
  - Set Lengths for Interleaved 2 of 5
  - I 2 of 5 Check Digit Verification
  - Transmit I 2 of 5 Check Digit
  - Convert I 2 of 5 to EAN-13
- Discrete 2 of 5 (DTF)
  - Enable/Disable Discrete 2 of 5
  - Set Lengths for Discrete 2 of 5
- Chinese 2 of 5
  - Enable/Disable Chinese 2 of 5
- Codabar (NW - 7)
  - Enable/Disable Codabar
  - Set Lengths for Codabar
  - CLSI Editing
  - NOTIS Editing
- MSI
  - Enable/Disable MSI
  - Set Lengths for MSI
  - MSI Check Digits
  - Transmit MSI Check Digit(s)
  - MSI Check Digit Algorithm
- GS1 DataBar (Formerly RSS, Reduced Space Symbology)
  - GS1 DataBar
  - Convert GS1 DataBar to UPC/EAN
- Redundancy Level
  - Redundancy Level 1
  - Redundancy Level 2
  - Redundancy Level 3
  - Redundancy Level 4
- Security Level
  - Security Level 0
  - Security Level 1
  - Security Level 2
  - Security Level 3
  - Bi-directional Redundancy
  - Intercharacter Gap Size
- Report Version
- Report MIMIC Version
- Report Synapse Cable
Miscellaneous Scanner Options
- Introduction
- Scanning Sequence Examples
- Errors While Scanning
- Miscellaneous Default Parameters
- Miscellaneous Scanner Parameters
Advanced Data Formatting
- Introduction
- Rules: Criteria Linked to Actions
- Using ADF Bar Codes
- ADF Bar Code Menu Example
- Special Commands
- Criteria
- Actions
- Alphanumeric Keyboard
Standard Default Parameters
Programming Reference
- Symbol Code Identifiers
- AIM Code Identifiers
Sample Bar Codes
- Code 39
- UPC/EAN
  - UPC-A, 100 %
  - EAN-13, 100 %
- Code 128
- Interleaved 2 of 5
- GS1 DataBar-14
Numeric Bar Codes
- Numeric Bar Codes
- Cancel
Glossary
Index
Tell Us What You Think...

USB Interface 7 - 11

USB Ignore Unknown Characters

This option applies only to the HID Keyboard Emulation device and IBM device. Unknown characters are

characters the host does not recognize. Select Send Bar Codes With Unknown Characters to send all bar code

data except for unknown characters. The scanner sounds no error beeps.

Select Do Not Send Bar Codes With Unknown Characters to prevent sending bar codes containing at least one

unknown character to the host. The scanner sounds an error beep.

*Send Bar Codes with Unknown Characters

(Transmit)

Do Not Send Bar Codes with Unknown Characters

(Disable)