User Guide

1 of 4
QUICK START GUIDE: I/O Expansion Card
www.symetrix.co | +1.425.778.7728
• The lightning ash with arrowhead
symbol within an equilateral triangle is
intended to alert the user of the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of su󰀩cient magnitude to constitute
a risk of electric shock to persons. The
exclamation point within an equilateral
triangle is intended to alert the user of
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product (i.e.
this Quick Start Guide).
• CAUTION: To prevent electric shock,
do not use the polarized plug supplied
with the device with any extension cord,
receptacle, or other outlet unless the
prongs can be fully inserted.
• Power Source: This Symetrix hardware
uses a universal input supply that
automatically adjusts to the applied
voltage. Ensure that your AC mains
voltage is somewhere between 100-240
VAC, 50-60 Hz. Use only the power
cord and connector specied for the
product and your operating locale. A
protective ground connection, by way of
the grounding conductor in the power
cord, is essential for safe operation. The
appliance inlet and coupler shall remain
readily operable once the apparatus has
been installed.
• User Serviceable Parts: There are no
user serviceable parts inside this Symetrix
product. In case of failure, customers
inside the U.S. should refer all servicing to
the Symetrix factory. Customers outside
the U.S. should refer all servicing to an
authorized Symetrix distributor. Distributor
contact information is available online at:
http://www.symetrix.co.
AVIS:
NE PAS OUVRIR
Il ne se trouve a l’interieur aucune piece pourvant entre reparée l’usager.
SEE OWNERS MANUAL. VOIR CAHIER D’INSTRUCTIONS.
S’adresser a un reparateur compétent.
RISQUE DE CHOC ELECTRIQUE
No user serviceable parts inside. Refer servicing to qualified service personnel.
CAUTION
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE
DO NOT OPEN
RISK OF ELECTRIC SHOCK
Important Safety Instructions
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
This apparatus shall not be exposed
to dripping or splashing and no objects
lled with liquids, such as vases, shall be
placed on the apparatus.
6 Clean only with dry cloth.
7 Do not block any ventilation openings.
Install only in accordance with the
manufacturer’s instructions.
8 Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including ampliers) that
produce heat.
9 This apparatus shall be connected to
a mains socket outlet with a protective
earthing connection. Do not defeat
the safety purpose of the polarized or
grounding-type plug. A polarized plug has
two blades with one wider than the other.
A grounding type plug has two blades and
a third grounding prong. The wide blade
or the third prong are provided for your
safety. If the provided plug does not t
into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Ensure proper ESD control and grounding
when handling exposed I/O terminals.
11 Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
12 Only use attachments/accessories
specied by the manufacturer.
13 Use only with the cart, stand, tripod,
bracket, or table specied
by the manufacturer, or
sold with the apparatus.
When a cart is used, use
caution when moving the
cart/apparatus combination
to avoid injury from tip-over.
14 Unplug this apparatus during lightning
storms or when unused for long periods of
time.
15 Refer all servicing to qualied service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
cord is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally, or
has been dropped.
• Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment under FCC rules.
• Cet appariel numerique de la classe B respecte toutes les Exigences
du Reglement sur le materiel brouilleur du Canada.
• The 2-line analog telephone interface card device is in compliance
with the Federal Communications Commission’s (FCC) Rules and
Regulations 47 CFR Part 68, and the Administrative Council on
Terminal Attachments (ACTA) – adopted technical criteria, TIA-968-B
– Telephone Terminal Equipment, Technical Requirements For
Connection of Terminal Equipment To The Telephone Network, August
2009 and TIA-1096.
• The 2-line analog telephone interface card device meets the Industry
Canada technical specifications CS-03 Part I for terminal equipment
and related access arrangements intended for direct connection
to analogue wireline facilities and DC-01(E) for the declaration
of conformity and registration of terminal equipment. The Ringer
Equivalence Number (REN) is an indication of the maximum number
of devices allowed to be connected to a telephone interface. The
REN for the Analog Telephone Interface (ATI) card is two. The
termination of an interface may consist of any combination of devices
subject only to the requirement that the sum of the REN’s not exceed
two per ATI card. Multiple ATI Cards may be installed to increase the
REN for a system.
What Ships in the Box
• I/O card.
• Card bracket.
• 2 black 4-40 Phillips head screws.
• 3 stainless steel 4-40 Phillips head
screws.
• 2 or 4 detachable three position 3.81 mm
terminal block connectors.
Note: Terminal block connectors are not
included with the 2 Line Analog Telephone
Interface Card, 2 Line VoIP Interface Card, or
the USB Audio Card.
• This Quick Start Guide.
What You Need to Provide
• Radius 12x8 EX, Radius AEC, Radius NX
4x4, Radius NX 12x8, or Edge.
• Anti-static work station.
Getting Help
Composer, the Windows software that
configures Symetrix Dante Network Audio
hardware, includes a help file which acts as
a complete User’s Guide for both hardware
and software. If you have questions beyond
the scope of this Quick Start Guide, contact
our Customer Support Group in the following
ways:
Tel: [phone] ext. 5
6:00 am to 5:00 pm PST
Monday through Friday
Web: https://www.symetrix.co
Email: [e-mail]
Forum: https://forum.symetrix.co