Installation Guide

ManualsBrandsSymmons ManualsPlumbingDia 1-Handle Shower Valve Trim in Chrome (Valve Not Included)

Dia

Model Numbers

Dia Trim Series

Dia Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

3500-CYL-B-TRM

Shower Valve Trim

3501-CYL-B-TRM

Shower Trim

3502-CYL-B-TRM

Tub/Shower Trim

3503-H321-V-CYL-B-TRM

Hand Shower Trim

3505-H321-V-CYL-B-TRM

Shower/Hand Shower Trim

3506-H321-V-CYL-B-TRM

Tub/Shower/Hand Shower Trim

3520-B-TRM

Shower Valve Trim

3521-B-TRM

Shower Trim

3522-B-TRM

Tub/Shower Trim

3530-B-TRM

Shower Valve Trim

3531-B-TRM

Shower Trim

3532-B-TRM

Tub/Shower Trim

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete warranty information.

Go to www.symmons.com/register to register your Symmons product.

TRIM, TA-10, T-12A

3500CYLBTRMTC

Shower Valve Trim

3501CYLBTRMTC

Shower Trim

3502CYLBTRMTC

Tub/Shower Trim

3503H321CYLBTRMTC

Hand Shower Trim

3505H321CYLBTRMTC

Shower/Hand Shower Trim

3506H321CYLBTRMTC

Tub/Shower/Hand Shower Trim

3520BTRMTC

Shower Valve Trim

3521BTRMTC

Shower Trim

3522BTRMTC

Tub/Shower Trim

3530BTRMTC

Shower Valve Trim

3531BTRMTC

Shower Trim

3532BTRMTC

Tub/Shower Trim

Warranty

3500-CYL-B-TRM

3500CYLBTRMTC

3501-CYL-B-TRM

3501CYLBTRMTC

3502-CYL-B-TRM

3502CYLBTRMTC

3520-B-TRM

3520BTRMTC

3521-B-TRM

3521BTRMTC

3522-B-TRM

3522BTRMTC

3530-B-TRM

3530BTRMTC

3531-B-TRM

3531BTRMTC

3532B-TRM

3532BTRMTC

3505-H321-V-CYL-B-TRM

3505H321CYLBTRMTC

3503-H321-V-CYL-B-TRM

3503H321CYLBTRMTC

3506-H321-V-CYL-B-TRM

3506H321CYLBTRMTC

TA-10T-12A

Summary of content (8 pages)

PAGE 1
Dia® Dia Trim Series Dia Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A 3500-CYL-B-TRM Shower Valve Trim 3500CYLBTRMTC Shower Valve Trim 3501-CYL-B-TRM Shower Trim 3501CYLBTRMTC Shower Trim 3502-CYL-B-TRM Tub/Shower Trim 3502CYLBTRMTC Tub/Shower Trim 3503-H321-V-CYL-B-TRM Hand Shower Trim 3503H321CYLBTRMTC Hand Shower Trim 3505-H321-V-CYL-B-TRM Shower/Hand Shower Trim 3505H321CYLBTRMTC Shower/Hand S
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (2mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions FIGURE 2 A Measurements A B C B D D C H E E F G H I J F G K L M N J O P Q L K R M R N O P S T U V W X I FLOOR Q S Y Z V Ø 2-1/2", 64 mm 6-3/4", 171 mm 6", 152 mm Male 1/2-14 NPT thread must be recessed 1/4" (6 mm) from finished wall Ref. 77", 1956 mm 3-1/2", 89 mm Ø 5", 127 mm Ø 7-1/2", 191 mm Ø 2-1/2", 64 mm Ref.
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system. 1 PACKING NUT Replacement Parts Description Part Number FIGURE 3 4.
PAGE 4
7.
PAGE 5
8. Installation - Shower Valve Trim 1) Secure large mounting plate to Temptrol pressure balancing valve using mounting screws (FIGURE 8.1). FIGURE 8.1 FIGURE 8.2 2) Secure large shower escutcheon to mounting plate. Tabs should snap in place (FIGURE 8.2). 3) Install dome cover by turning clockwise (FIGURE 8.3). 4) Install handle to shower valve. Secure with set screw (FIGURE 8.4). FIGURE 8.3 FIGURE 8.4 9.
PAGE 6
11. Installation - Slide Bar Assembly 1a) D ry Wall Option: Remove upper and lower caps from slide bar brackets. Place slide bar into desired position. Using brackets as a guide, carefully drill 3/16" holes into wall. Remove slide bar and install anchors. Note: Slide bar holes and bracket holes must be aligned before drilling. Before drilling bottom hole, make sure slide bar is plumb (FIGURE 11.1A). 1 3 1 1b) S tud Option: Remove upper and lower caps from slide bar brackets.
PAGE 7
12. Operation (Temperature Control) 1) Turn shower handle counter-clockwise approximately 1/4 turn to put valve in cold position (FIGURE 12.1). FIGURE 12.2 FIGURE 12.3 FIGURE 13.2 FIGURE 13.3 FIGURE 14.1 FIGURE 14.2 FIGURE 14.3 FIGURE 14.4 FIGURE 14.5 FIGURE 14.6 FIGURE 12.1 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 12.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 12.3). 13.
PAGE 8
15. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.