Installation Sheet

ManualsBrandsSymmons ManualsPlumbingDuro 1-Handle Wall-Mounted Diverter Trim Kit in Brushed Bronze (Valve Not Included)

Duro

Model Numbers

Duro Trim Series

Duro Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

S-3600-TRM

Shower Valve Trim

S-3601-TRM

Shower Trim

S-3602-TRM

Tub/Shower Trim

S-3604-H321-V-TRM

Tub/Hand Shower Trim

S3608TRM

Shower/Hand Shower Trim

TRIM, TA-10, T-12A

S3600TRMTC

Shower Valve Trim

S3601TRMTC

Shower Trim

S3602TRMTC

Tub/Shower Trim

S3604H321TRMTC

Tub/Hand Shower Trim

S3608TRMTC

Shower/Hand Shower Trim

S-3600-TRM

S3600TRMTC

S-3601-TRM

S3601TRMTC

S-3602-TRM

S3602TRMTC

S3608TRM

S3608TRMTC

S-3604-H321-V-TRM

S3604H321TRMTC

TA-10T-12A

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Go to www.symmons.com/register to register your

Symmons product.

Warranty

Summary of content (8 pages)

PAGE 1
Duro® Duro Trim Series Duro Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A S-3600-TRM Shower Valve Trim S3600TRMTC Shower Valve Trim S-3601-TRM Shower Trim S3601TRMTC Shower Trim S-3602-TRM Tub/Shower Trim S3602TRMTC Tub/Shower Trim S-3604-H321-V-TRM Tub/Hand Shower Trim S3604H321TRMTC Tub/Hand Shower Trim S3608TRM Shower/Hand Shower Trim S3608TRMTC Shower/Hand Shower Trim T-12A S-3600-TRM S3600TR
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (3mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions Measurements FIGURE 2 A A B C B D D E F G H C I J K L E M N F O G P K J H I FLOOR L O N M P Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater. 3) All dimensions measured from nominal rough-in (see M as reference).
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system.
PAGE 4
7. Parts Breakdown FIGURE 7 C L K B Item M N A O H A B C D E F G H I F J K L M N O P G G E D I Replacement Parts Description Part Number Showerhead Shower Arm Flange Standard Handle Dome Cover Shower Escutcheon Screws Mounting Plate Diverter/Volume Control Handle Tub Spout 362SH 300S T-617 RTS-037 RTS-003 RTS-004 067 Slide Bar Assembly RA-009 Hand Shower Wall Elbow 60" Hose EF-100 EF-105 RTS-045 Notes: 1) Append appropriate suffix for premium finish.
PAGE 5
8. Installation - Shower Valve Trim 1) Secure large mounting plate to Temptrol pressure balancing valve using mounting screws (FIGURE 8.1). FIGURE 8.1 FIGURE 8.2 FIGURE 8.3 FIGURE 8.4 2) Place diverter/volume control handle into slot in shower escutcheon (FIGURE 8.2). 3) Secure large shower escutcheon to mounting plate. Guide handle into control port on valve body. Tabs should snap in place (FIGURE 8.3). 4) Install dome cover by turning clockwise (FIGURE 8.4). 5) Install handle to shower valve.
PAGE 6
10. Installation - Slide Bar Assembly 1a) D ry Wall Option: Remove upper and lower caps from slide bar brackets. Place slide bar into desired position. Using brackets as a guide, carefully drill 3/16" holes into wall. Remove slide bar and install anchors. Note: Slide bar holes and bracket holes must be aligned before drilling. Before drilling bottom hole, make sure slide bar is plumb (FIGURE 10.1A). 1 3 1 1b) S tud Option: Remove upper and lower caps from slide bar brackets.
PAGE 7
11. Operation (Temperature Control) 1) Turn shower handle counter-clockwise approximately 1/4 turn to put valve in cold position (FIGURE 11.1). FIGURE 11.2 FIGURE 11.1 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 11.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 11.3). 12.
PAGE 8
14. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.