Installation Guide

ManualsBrandsSymmons ManualsBathNaru Single-Handle 3-Spray Tub and Shower Faucet in Chrome

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ (800)796-6667 ■ Fax: (800)961-9621

■

www.symmons.com

■

gethelp@symmons.com

■

ZV-3051 REV 0 09/25/14

4103-TRM, 4105-TRM, 4106-TRM

Naru

™

Trim Series

Operation & Maintenance Manual

Model Numbers Speciﬁcations

4103-TRM Hand Shower Trim

4105-TRM Shower Trim with Hand Shower

4106-TRM Tub/Shower Trim with Hand

Shower

Tub/shower trim with hand shower and lever handle

includes wall connection, cradle for hand shower

mounting, in-line vacuum breaker, exible metal hose,

non-diverter tub spout, 3 mode hand shower and

3 mode showerhead with standard 2.5 gpm (9.5 L/min)

ow restrictor. Shower trim with hand shower and lever

handle includes all of the above less non-diverter tub

spout. Valve trim with hand shower and lever handle

includes all of the above less non-diverter tub spout and

3 mode showerhead. Components made from metal and

nonmetallic materials plated in standard polished

chrome nish.

Modiﬁcations Compliance

-1.5 1.5 gpm (5.7 L/min) ﬂow restrictor

-2.0 2.0 gpm (7.6 L/min) ﬂow restrictor

-412HSB 30" slide bar in place of wall cradle on

hand shower units

-PNL Polished nickel ﬁnish

-STN Satin nickel ﬁnish

-ASME A112.18.1; CSA B125.1

Warranty

Limited Lifetime - to the original end purchaser in

consumer installations.

5 Years - for commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Note: Append appropriate -sufx to model number.

Summary of content (6 pages)

PAGE 1
4103-TRM, 4105-TRM, 4106-TRM Naru™ Trim Series Operation & Maintenance Manual Model Numbers Specifications 4103-TRM Hand Shower Trim 4105-TRM Shower Trim with Hand Shower 4106-TRM Tub/Shower Trim with Hand Shower Modifications Tub/shower trim with hand shower and lever handle includes wall connection, cradle for hand shower mounting, in-line vacuum breaker, flexible metal hose, non-diverter tub spout, 3 mode hand shower and 3 mode showerhead with standard 2.5 gpm (9.5 L/min) flow restrictor.
PAGE 2
Dimensions Measurements A B D C F E J H G I N M L K O R P Q S Floor A Ø 2 1/4", 57 mm B 8 1/4", 210 mm C Ø 2 1/4", 57 mm D Female 1/2" IPS thread must be recessed 7/8" from finished wall E 6", 152 mm right or left F 77", 1956 mm G Ø 7 1/2", 191 mm H Ø 5", 127 mm I 8", 203 mm J 4 3/4", 121 mm (4106-TRM) 4 7/8", 124 mm (4105-TRM) K 2 1/8", 54 mm L 32", 813 mm (4106-TRM) 45", 1143 mm (4103-TRM, 4105-TRM) M 12", 305 mm N 2 1/4", 57 mm O 3", 76 mm P 1/2" NPT Q 1/2"
PAGE 3
Parts Breakdown Replacement Parts C F E B A N M D O K I J X H T V P L U G Q W R Y S Z Item Description Part Number A Z Vacuum Breaker 60" Hose EF-104 B C Wall Elbow Wall Elbow Flange T-444-KIT D Showerhead 412SH E F Shower Arm Shower Arm Flange 300 G H Diverter Handle Set Screw LLD-102 I Diverter Dome Cover LLD-101 J K L Diverter Escutcheon Mounting Screws Mounting Plate T-416A M N O P Q Cradle Mount Cradle Mounting Screws Washer Cradle Arm Set Screw T-545 R S S
PAGE 4
Installation Note: For valve body installation, please see valve body installation guides. W U G H Note: Tabs should snap into place. 1 1 4) Install shower dome cover (T) and diverter dome cover (I) to valves by turning clockwise. K 5) Install diverter handle (G) (4105-TRM and 4106-TRM only) and shower handle (R) to valves. Secure handles by tightening set screws (H, S).
PAGE 5
Installation 8) Press tab to remove mounting plate (M2) from cradle mount cover (M1). 10) Install mounting plate (M2). Secure with two screws (N). Replace cradle mount cover (M1). 1 1 M2 13) Install shower head (D) to shower arm (E) turning clockwise to tighten. N M2 2 E 1 M2 2 M1 2 D 3 M1 Note: Mounting plate (M2) center tabs must be horizontal for removal. 9) Place mounting plate (M2) in position, mark and drill 1/8" pilot holes into stud.
PAGE 6
Operation Diverter Control Temperature Control 1) Turn shower handle counterclockwise approximately 1/4 turn to put valve in cold position. 1) D iverter handle facing straight down is for diverter function 1. 2) 4 130-TRM & 4105-TMRM: Turn diverter handle counterclockwise one full revolution for diverter function 2. 2) T urn shower handle counterclockwise approximately 1/2 turn to put valve in warm position. 4106-TRM: Turn diverter handle counterclockwise 1/4 turn for diverter function 2.