Installation Sheet

ManualsBrandsSymmons ManualsPlumbingSereno Collection 9.25" Wall Mounted Pressure Balanced Valve Trim with Lever Handle in Satin Nickel

1

2

3

4

5

6

7

Sereno

®

Model Numbers

Sereno Trim Series

Sereno Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

4300-TRM

Shower Valve Trim

4301-TRM

Shower Trim

4303-TRM

Hand Shower Trim

4305-TRM

Shower/Hand Shower Trim

4306-TRM

Tub/Shower/Hand Shower Trim

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete warranty information.

Go to www.symmons.com/register to register your Symmons product.

TRIM, TA-10, T-12A

4300TRMTC

Shower Valve Trim

4301TRMTC

Shower Trim

4303TRMTC

Hand Shower Trim

4305TRMTC

Shower/Hand Shower Trim

4306TRMTC

Tub/Shower/Hand Shower Trim

Warranty

TA-10T-12A

4300-TRM

4300TRMTC

4301-TRM

4301TRMTC

4305-TRM

4305TRMTC

4306-TRM

4306TRMTC

4303-TRM

4303TRMTC

Summary of content (8 pages)

PAGE 1
Sereno® Sereno Trim Series Sereno Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A 4300-TRM Shower Valve Trim 4300TRMTC Shower Valve Trim 4301-TRM Shower Trim 4301TRMTC Shower Trim 4303-TRM Hand Shower Trim 4303TRMTC Hand Shower Trim 4305-TRM Shower/Hand Shower Trim 4305TRMTC Shower/Hand Shower Trim 4306-TRM Tub/Shower/Hand Shower Trim 4306TRMTC Tub/Shower/Hand Shower Trim T-12A 4300-TRM 4300TRMTC
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions Measurements FIGURE 2 B A A B C D D E C F I G J H F G H I J K L M N O P Q R S T M L K U Q P N E O V R U S T V Floor Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater. 3) All dimensions measured from nominal rough-in (see U as reference).
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system.
PAGE 4
7.
PAGE 5
8. Installation - Shower Valve Trim 1) Secure large shower escutcheon to Temptrol pressure balancing valve using mounting screws (FIGURE 8.1). FIGURE 8.2 FIGURE 8.1 2) Install dome cover and lock nut to valve by turning clockwise (FIGURE 8.2). 3) Install handle to shower valve. Secure with star washer, set screw and plug button (FIGURE 8.3). FIGURE 8.3 9. Installation - Diverter Valve Trim 1) Secure small mounting plate to Symmons diverter valve using mounting screws (FIGURE 9.1). FIGURE 9.
PAGE 6
11. Installation - Slide Bar Assembly 1) Press tab to remove mounting plate from cradle mount cover (FIGURE 11.1). Note: Mounting plate center tabs must be horizontal for removal. 1 2) Place mounting plate in position, mark and drill 3/16" holes into drywall. Install anchors (FIGURE 11.2). Stud Option: Place mounting plate in position, mark and drill 1/8" pilot holes into stud. FIGURE 11.1 1 FIGURE 11.2 2 2 3) I nstall mounting plate. Secure with two screws.
PAGE 7
12. Operation (Temperature Control) 1) Turn shower handle counter-clockwise approximately 1/4 turn to put valve in cold position (FIGURE 12.1). FIGURE 12.2 FIGURE 12.3 FIGURE 13.2 FIGURE 13.3 FIGURE 14.1 FIGURE 14.2 FIGURE 14.3 FIGURE 14.4 FIGURE 14.5 FIGURE 14.6 FIGURE 12.1 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 12.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 12.3). 13.
PAGE 8
15. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.