Installation Guide

ManualsBrandsSymmons ManualsMixing ValvesAllura Shower Valve

Model Numbers Speciﬁcation

Options/Modiﬁcations

Tub/shower trim with lever handle includes diverter tub

spout and 3 mode showerhead with standard 2.5 gpm

(9.5 L/min) ow restrictor. Shower trim with lever

handle includes all of the above less diverter tub

spout. Valve trim with lever handle includes valve trim

only. Components made from metal and nonmetallic

materials plated in standard polished chrome nish.

Allura

Trim Series

Operation & Maintenance Manual

4700-TRM, 4701-TRM, 4702-TRM

4700-TRM

Valve Trim

Compliance

-1.5

1.5 gpm (5.7 L/min) ﬂow restrictor

-2.0

2.0 gpm (7.6 L/min) ﬂow restrictor

-LAM

Metal ﬁnish insert handle

-LR

Lever handle

4701-TRM

Shower Trim

Note: Append appropriate -sufx to model number.

-STN

Satin Nickel ﬁnish

-ASME A112.18.1; CSA B125.1

4702-TRM

Tub/Shower Trim

-SS

Slip spout on any tub and shower unit

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Summary of content (5 pages)

PAGE 1
4700-TRM, 4701-TRM, 4702-TRM Allura® Trim Series Operation & Maintenance Manual Model Numbers 4700-TRM Valve Trim 4701-TRM Shower Trim 4702-TRM Tub/Shower Trim Options/Modifications -1.5 1.5 gpm (5.7 L/min) flow restrictor -2.0 2.0 gpm (7.6 L/min) flow restrictor -LAM Metal finish insert handle -LR Lever handle -SS Slip spout on any tub and shower unit -STN Satin Nickel finish Note: Append appropriate -suffix to model number.
PAGE 2
Dimensions A A B C D E B F G H I J D K I C H G J K F E Floor L M N Notes: 1) All dimensions measured from nominal rough-in (see K as reference). 2) Dimensions subject to change without notice. 2 L M N Measurements Ø 2 1/2”, 64 mm 6 3/4”, 172 mm Ø 7”, 178 mm Ref. 77”, 1956 mm 2 1/2", 64 mm Ref. 32”, 813 mm (4702-TRM) Ref.
PAGE 3
Parts Breakdown Replacement Parts B C D H I Part Number A Showerhead 4-143 B Flange Shower Arm (flange included) Plug Button Handle Screw Star Washer Handle Dome Cover Dial Mounting Screws Shower Escutcheon Diverter Tub Spout 430SS D E F G H I J K* L 300S RTS-026 T-19 T-133C 054 Notes: 1) Append -STN to part number for Satin Nickel finish. 2) Append -1.5 or -2.0 to showerhead for low flow.
PAGE 4
Installation Note: For valve body installation, please see valve body manual. 3) Install handle (G) to valve. Secure handle with star washer (F) and screw (E). Attach plug button (D) to handle. 5) A ttach shower arm (C) and flange (B) to vertical shower pipe turning clockwise to tighten. 1) Install escutcheon (K) to shower valve. Secure with two screws (J). Snap dial (I) into escutcheon.
PAGE 5
Operation & Maintenance Temperature Control 1) Turn shower handle counterclockwise approximately 1/4 turn to put valve in cold position. 3) Turn shower handle counterclockwise approximately 3/4 turn to put valve in hot position. 2) T urn shower handle counterclockwise approximately 1/2 turn to put valve in warm position. Troubleshooting Chart Finish is spotting. Elements in water supply may cause water staining on finish.