Installation Sheet

ManualsBrandsSymmons ManualsPlumbingAllura Collection Wall Mounted Tub and Shower Trim Set with Lever Handles in Satin Nickel

1

2

3

4

5

6

7

Allura

®

Model Numbers

Allura Trim Series

Allura Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

4700-TRM

Shower Valve Trim

4701-TRM

Shower Trim

4702-TRM

Tub/Shower Trim

4703-TRM

Hand Shower Trim

4705-TRM

Shower/Hand Shower Trim

4706-TRM

Tub/Shower/Hand Shower Trim

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete warranty information.

Go to www.symmons.com/register to register your Symmons product.

TRIM, TA-10, T-12A

4700TRMTC

Shower Valve Trim

4701TRMTC

Shower Trim

4702TRMTC

Tub/Shower Trim

4703TRMTC

Hand Shower Trim

4705TRMTC

Shower/Hand Shower Trim

4706TRMTC

Tub/Shower/Hand Shower Trim

Warranty

4700-TRM

4700TRMTC

4701-TRM

4701TRMTC

4702-TRM

4702TRMTC

4705-TRM

4705TRMTC

4703-TRM

4703TRMTC

4706-TRM

4706TRMTC

TA-10T-12A

Summary of content (8 pages)

PAGE 1
Allura® Allura Trim Series Allura Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A 4700-TRM Shower Valve Trim 4700TRMTC Shower Valve Trim 4701-TRM Shower Trim 4701TRMTC Shower Trim 4702-TRM Tub/Shower Trim 4702TRMTC Tub/Shower Trim 4703-TRM Hand Shower Trim 4703TRMTC Hand Shower Trim 4705-TRM Shower/Hand Shower Trim 4705TRMTC Shower/Hand Shower Trim 4706-TRM Tub/Shower/Hand Shower Trim 4706TRMTC Tub
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (3mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions FIGURE 2 A Measurements P A B B C D Q R C E F G H I J K D S F E G O H T J I K L M U N FLOOR Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater. 3) All dimensions measured from nominal rough-in (see I as reference).
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system.
PAGE 4
7. Parts Breakdown FIGURE 7 C Item Q A B C B T L A J R K S U I G H D P F N V O M G D O E Showerhead Shower Arm Flange Plug Button Screw Star Washer Handle Lock Nut Dome Cover Diverter Escutcheon Screws Mounting Plate Dome Cover Dial Screws Mounting Plate Hand Shower Wall Cradle Screws Mounting Plate Wall Elbow 60" Hose Tub Spout Diverter Tub Spout 4-143 300S RTS-026 T-19/20 T-416A T-19 T-133C EF-101 EF-106 EF-105 RTS-045 060 054 Notes: 1) Append appropriate suffix for premium finish.
PAGE 5
8. Installation - Shower Valve Trim 1) Secure large shower escutcheon to Temptrol pressure balancing valve using mounting screws. Snap dial into shower escutcheon (FIGURE 8.1). Note: Dial should be in the 6 o'clock position. FIGURE 8.1 2) Install dome cover by turning clockwise (FIGURE 8.2). FIGURE 8.2 2 3) Install handle to shower valve. Secure handle with star washer and screw. Attach plug button to handle (FIGURE 8.3). 1 FIGURE 8.3 9.
PAGE 6
11. Installation - Slide Bar Assembly 1) Place mounting plate in position. Mark and drill 3/16" holes for tile anchors, 5/16" holes for drywall anchors. Install anchors (FIGURE 11.1). Note: For dry wall 1/2" thick or less, insert anchor tool into drywall anchor to secure behind wall prior to installing wall cradle. 1 FIGURE 11.1 1 2) R emove cover of hand shower cradle. Install cradle and mounting plate. Secure with three screws. Replace cover on hand shower cradle (FIGURE 11.2).
PAGE 7
12. Operation (Temperature Control) 1) Turn shower handle counter-clockwise approximately 1/4 turn to put valve in cold position (FIGURE 12.1). FIGURE 12.2 FIGURE 12.3 FIGURE 13.2 FIGURE 13.3 FIGURE 14.1 FIGURE 14.2 FIGURE 14.3 FIGURE 14.4 FIGURE 14.5 FIGURE 14.6 FIGURE 12.1 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 12.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 12.3). 13.
PAGE 8
15. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.