Installation Sheet

ManualsBrandsSymmons ManualsPlumbingWinslet Collection 7.5" Wall Mounted Valve Trim Lever Handle in Polished Chrome

1

2

3

Winslet

®

Model Numbers

Winslet Trim Series

Winslet Trim Series with TA-10 Flow Control Spindle &

T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

5100-TRM

Shower Valve Trim

5101-TRM

Shower Trim

5103-TRM

Hand Shower Trim

5105-TRM

Shower/Hand Shower Trim

5106-TRM

Tub/Shower/Hand Shower Trim

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete warranty information.

Go to www.symmons.com/register to register your Symmons product.

TRIM, TA-10, T-12A

5100TRMTC

Shower Valve Trim

5101TRMTC

Shower Trim

5103TRMTC

Hand Shower Trim

5105TRMTC

Shower/Hand Shower Trim

5106TRMTC

Tub/Shower/Hand Shower Trim

Warranty

5100-TRM

5100TRMTC

5101-TRM

5101TRMTC

5105-TRM

5105TRMTC

5106-TRM

5106TRMTC

TA-10T-12A

5103-TRM

5103TRMTC

Summary of content (4 pages)

PAGE 1
Winslet® Winslet Trim Series Winslet Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A 5100-TRM Shower Valve Trim 5100TRMTC Shower Valve Trim 5101-TRM Shower Trim 5101TRMTC Shower Trim 5103-TRM Hand Shower Trim 5103TRMTC Hand Shower Trim 5105-TRM Shower/Hand Shower Trim 5105TRMTC Shower/Hand Shower Trim 5106-TRM Tub/Shower/Hand Shower Trim 5106TRMTC Tub/Shower/Hand Shower Trim T-12A 5100-TRM 5100TRMT
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (3mm) Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions Measurements FIGURE 2 B A A B C D D E C F E F G H I J K L M N G O I P H Q M N L K J FLOOR O P Q Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater. 3) All dimensions measured from nominal rough-in (see O as reference).
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system.
PAGE 4
7. Parts Breakdown FIGURE 7 C Item B L A N H F M G O E D K G I E J J D A B C D E F G H I J K L M N O P Replacement Parts Description Part Number Showerhead Shower Arm Flange Handle Assy.