Specification

ManualsBrandsSymmons ManualsBathUnity 1-Spray Hand Shower in Satin Nickel (Valve Included)

Unity

™

Model Numbers

Hand Shower System

Speciﬁcation Submittal

6603

Hand shower system powered by the Temptrol

Pressure Balancing valve. Features adjustable

stop screw to limit handle turn, wall cradle, in-line

vacuum breaker, 60” exible metal hose, hand shower

and standard 2.5 gpm (9.5 L/min) ow restrictor.

Components made from metal and nonmetallic materials

plated in standard polished chrome nish.

Speciﬁcation

Location:

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Compliance

Modiﬁcations

Note: Append appropriate -sufx to model number.



6603

Unity Hand Shower System

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

2.0 gpm (7.6 L/min)

Certied by

CSA Group



-1.5 1.5 gpm (5.7 L/min) ﬂow restrictor



-2.0 2.0 gpm (7.6 L/min) ﬂow restrictor



-X Integral service stops



-CHKS Integral check stops



-IPS

1/2” female IPS connections



-REV Reverse coring for back to back installa-

tions



-LP Loop handle



-QD

Quick disconnect on hand shower units



-R

White vinyl hose in place of metal hose



-OP 13” oval plate



-72

6’ hose in place of 5’ standard



-TRM Trim only, valve not included



-STN Satin Nickel ﬁnish

Reset Form

Summary of content (4 pages)

PAGE 1
Location: Unity™ 6603 Hand Shower System Specification Submittal Model Numbers Specification  6603 Hand shower system powered by the Temptrol® Pressure Balancing valve. Features adjustable stop screw to limit handle turn, wall cradle, in-line vacuum breaker, 60” flexible metal hose, hand shower and standard 2.5 gpm (9.5 L/min) flow restrictor. Components made from metal and nonmetallic materials plated in standard polished chrome finish. Unity Hand Shower System Modifications       -1.5 1.
PAGE 2
Dimensions Measurements A B C D E A G F G H I B 3 1/2”, 89 mm Male 1/2” NPT fitting must be recessed 1/4” from finished wall Shower Valve Hole Size Min. Ø 3”, 76 mm Max. Ø 4”, 102 mm 3 3/4”, 95 mm Rough-in 2 3/8” ± 1/2”, 60 mm ± 13 mm Ref. 42”, 1067 mm 2 1/8”, 54 mm Ø 6 3/8”, 162 mm 3 1/2”, 89 mm H C D I E F FLOOR Notes: 1) All dimensions measured from nominal rough-in (see E as reference). 2) Dimensions subject to change without notice. Symmons Industries, Inc.
PAGE 3
Emplacement: Unity™ 6603 Système douche à main Présentation des spécifications Numéro de modèle Spécification  6603 Le système de douche à main comprend la vanne à pression autorégularisée Temptrol®. Figurer la vis d’arrêt réglable pour limiter le tournage de la poignée, une support de douche à main, 60 po tuyau flexible en métal et 1 douche à main avec un réducteur de débit régulier de 2,5 gpm (9,5 L/min).
PAGE 4
Dimensions Mesures A B C D A E G F G H I B H 3 1/2 po, 89 mm 1/2 po mâle à filets NPT doit faire encastré de 1/4 po du mur fini Taille du trou Min. Ø 3 po, 76 mm Max. Ø 4 po, 102 mm 3 3/4 po, 95 mm Robinetterie brute 2 3/8 po ± 1/2 po, 60 mm ± 13 mm Réf. 42 po, 1067 mm 2 1/8 po, 54 mm Ø 6 3/8 po, 162 mm 3 1/2 po, 89 mm C D I E F FLOOR Remarques: 1) Toutes les dimensions sont mesurées à partir de la robinetterie brute nominale (voir E en référence).