Installation Guide

ManualsBrandsSymmons ManualsBathIdentity Single-Handle 1-Spray Shower Faucet in Satin Nickel (Valve Included)

Identity

™

Model Numbers

6700, 6701, 6702

Operation & Maintenance Manual

Speciﬁcation

Modiﬁcations

Note: Append appropriate -sufx to model number.



6700

Identity Tub/Shower System



6701

Identity Shower System



6702

Identity Tub/Shower System

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

6700

Tub/shower system powered by the Temptrol

pressure-

balancing valve. Features adjustable stop screw to

limit handle turn. Components made from metal and

nonmetallic materials, plated in standard polished chrome

nish.

6701

Shower system powered by the Temptrol

pressure-

balancing valve. Features adjustable stop screw to limit

handle turn, 1 mode showerhead with easy to clean rubber

nozzles and standard 2.5 gpm (9.5 L/min) ow restrictor.

Components made from metal and nonmetallic materials,

plated in standard polished chrome nish.

6702

Tub/shower system powered by the Temptrol

pressure-

balancing valve. Features adjustable stop screw to limit

handle turn, diverter tub spout, 1 mode showerhead with

easy to clean rubber nozzles and standard 2.5 gpm

(9.5 L/min) ow restrictor. Components made from metal

and nonmetallic materials, plated in standard polished

chrome nish.



-1.5 1.5 gpm (5.7 L/min) ﬂow restrictor



-2.0 2.0 gpm (7.6 L/min) ﬂow restrictor



-143 3 mode showerhead



-145 5 mode showerhead



-231 2 mode showerhead



-CHKS Integral check stops - for use in

installations where a positive shut-off

device is used downstream of mixing valve



-IPS

1/2" female IPS connections



-L/HD

Less showerhead



-LP Loop handle



-LR Lever handle



-OP 13" oval plate



-REB-TRM

Rebuild trim kit



-REV Reverse coring, hot on right, cold on

left, for back to back installations



-SS Slip spout on any tub/shower unit



-STN Satin Nickel ﬁnish



-TRM Trim only, valve not included



-X Integral service stops - allows water

shutoff at valve for service

Compliance

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

Certied by

CSA Group

For California Residents

WARNING: This product contains chemicals known to

the State of California to cause cancer, birth defects, or

other reproductive harm.

Summary of content (15 pages)

PAGE 1
Identity™ 6700, 6701, 6702 Operation & Maintenance Manual Model Numbers Specification  6700 6700 Tub/shower system powered by the Temptrol® pressurebalancing valve. Features adjustable stop screw to limit handle turn. Components made from metal and nonmetallic materials, plated in standard polished chrome finish. Identity Tub/Shower System  6701 Identity Shower System  6702 Identity Tub/Shower System Modifications       -1.5 1.5 gpm (5.7 L/min) flow restrictor -2.0 2.0 gpm (7.
PAGE 2
Dimensions A Measurements M A B C D E B N F G H I J K D C F E O G I H J K P L FLOOR Notes: 1) All dimensions measured from nominal rough-in (see I as reference). 2) Dimensions subject to change without notice. 2 L M N O P 5-7/8", 149 mm 4-5/8", 117 mm 3-1/2", 89 mm 2-7/8", 73 mm Ref. 77", 1956 mm Shower Valve Hole Size Min. Ø 3", 76 mm Max.
PAGE 3
Parts Breakdown Replacement Parts C B A I G H Item Description Part Number A Showerhead 672SH* B C D E Shower Arm Flange Handle Set Screw F Dome Cover T-19* G H I Shower Escutcheon Kit 6700-ESC* J Tub Spout 054* 300S* RTS-281* *Note: Append -STN to part number for Satin Nickel finish.
PAGE 4
Installation Note: For valve body installation, please see valve body manual. 3) Install dome cover (F) to shower valve by turning clockwise. 1) Install shower mounting plate (I) to shower valve. Secure with two screws (H). I 5) Install tub spout (J) to pipe fitting Turn clockwise to tighten. G 1 J 1 2 F 2 1 H 2 H 4) Install shower handle (D) to shower valve. Secure shower handle with set screw (E). 6) Attach shower arm (B) and flange (C) to vertical shower pipe.
PAGE 5
Operation (Temperature Control) 1) Turn shower handle counterclockwise approximately 1/4 turn to put valve in cold position. 2) Turn shower handle counterclockwise approximately 1/2 turn to put valve in warm position. 3) Turn shower handle counterclockwise approximately 3/4 turn to put valve in hot position. Operation (Diverter Control for 6702 only) 1) D iverter lever in down position for tub spout operation. 2) D iverter lever in up position for shower operation.
PAGE 6
Identity™ 6700, 6701, 6702 Manual de funcionamiento y mantenimiento Números de modelo Especificación  6700 6700 Sistema para bañera y ducha con válvula compensadora de presión Temptrol®. Incluye un tornillo con tope ajustable para limitar el giro de la manija. Las piezas están fabricadas con materiales metálicos y no metálicos recubiertos con el acabado estándar de cromo pulido.
PAGE 7
Dimensiones A Medidas M A B C D E B N F G H I J D C F E K O G I H J K P L PISO Notas: 1) Todas las dimensiones tomadas desde el empotrado (ver I para referencia). 2) Las dimensiones están sujetas a cambios sin previo aviso. 7 L M N O P 5-7/8", 149 mm 4-5/8", 117 mm 3-1/2”, 89 mm 2-7/8", 73 mm Ref. 77”, 1956 mm Tamaño de los orificios de la válvula para ducha Mín. Ø 3”, 76 mm Máx.
PAGE 8
Desglose de piezas Repuestos C Artículo Descripción B A B C D E A F I G F G H I J H D J 672SH* 300S* RTS-281* T-19* 6700-ESC* 054* *Nota: Anexar -STN al número de pieza para acabado de níquel satinado.
PAGE 9
Instalación Nota: Para instalar el cuerpo de la válvula, vea el manual de la válvula. 3) Instale la cubierta del domo (F) a la válvula de la ducha girándola en el sentido de las manecillas del reloj. 1) Instale la placa de montaje (I) a la válvula de la ducha. Sujétela con dos tornillos (H). G 2 H 2 F 1 2 4) Instale la manija la ducha (D) en la válvula de la ducha. Sujete la manija de la ducha con el tornillo de presión (E).
PAGE 10
Funcionamiento (Control de temperatura) 1) Gire el mango de la ducha 1/4 de vuelta en sentido contrario a las manecillas del reloj para colocar la válvula en la posición de agua fría. 2) Gire el mango de la ducha 1/2 de vuelta en sentido contrario a las manecillas del reloj para colocar la válvula en la posición de agua tibia. 3) Gire el mango de la ducha 3/4 de vuelta en sentido contrario a las manecillas del reloj para colocar la válvula en la posición de agua caliente.
PAGE 11
Identity™ 6700, 6701, 6702 Manuel d'utilisation et d'entretien Numéros de modèle Spécifications  6700 6700 Système de baignoire/douche Identity  6701 Système de douche Identity  6702 Système de baignoire/douche Identity 6701 Modifications       -1.5 Réducteur de débit de 1,5 gpm (5,7 L/min) -2.
PAGE 12
Dimensions A Mesures M A B C D E B N D C F E O G I 5-7/8 po, 149 mm 4-5/8 po, 117 mm 3-1/2 po, 89 mm 2-7/8 po, 73 mm Réf. 77 po, 1956 mm Taille du trou pour la vanne de douche F Min. Ø 3 po, 76 mm Max. Ø 4 po, 102 mm G 3-1/2 po, 89 mm H 12 po, 305 mm Robinetterie brute I 2-3/8 po ± 1/2po, 60 mm ± 13 mm Raccord NPT 1/2 po mâle doit J faire saillie de 4 po (102 mm) du mur fini 6700, 6702 Réf. 32 po, 813 mm K 6701 Réf.
PAGE 13
Liste des pièces C Article B A I G F H Pièces de rechange Numéro Description de pièce A Pomme de douche 672SH* B C D E Bras et bride de douche Assemblage Vis de pression F Couvercle en dôme T-19* G H I Douche Ensemble rosace 6700-ESC* J Bec de baignoire 054* 300S* RTS-281* *Remarque : Juxtaposer le -STN au numéro de pièce pour le fini nickel satiné.
PAGE 14
Installation Remarque : Pour l'installation du corps de vanne, veuillez consulter le manuel du corps de vanne. 3) Installez le couvercle en dôme (F) à la vanne de douche en tournant dans le sens des aiguilles d'une montre. 1) Installez la plaque de montage de la douche (I) à la vanne de douche. Fixez avec deux vis (H). I G 2 F 2 H 1 J 1 2 1 H 5) Installez le bec de baignoire (J) au raccord de tuyauterie en tournant dans le sens horaire pour serrer.
PAGE 15
Fonctionnement (Contrôle de la température) 1) Tournez la poignée de douche dans le sens contraire des aiguilles d'une montre approximativement 1/4 de tour pour mettre la vanne dans la position d'eau froide. 2) Tournez la poignée de douche dans le sens contraire des aiguilles d'une montre approximativement 1/2 de tour pour mettre la vanne dans la position d'eau tiède.