Installation Sheet

ManualsBrandsSymmons ManualsPlumbingOrigins Collection 9604-X-PLR-STN Wall Mounted Tub and Handshower Trim Set with Lever Handle in Satin Nickel

Origins

Model Numbers

Origins Trim Series

Origins Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

S-9600-P-TRM

Shower Valve Trim

S-9600-PLR-TRM

Shower Valve Trim

S-9601-P-TRM

Shower Trim

S-9601-PLR-TRM

Shower Trim

S-9602-P-TRM

Tub/Shower Trim

S-9602-PLR-TRM

Tub/Shower Trim

S-9603-PLR-TRM

Hand Shower Trim

S-9604-PLR-TRM

Tub/Hand Shower Trim

S-9606-PLR-TRM

Tub/Shower/Hand Shower Trim

S-9608-PLR-TRM

Shower/Hand Shower Trim

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Go to www.symmons.com/register to register your

Symmons product.

TRIM, TA-10, T-12A

S9600PTRMTC

Shower Valve Trim

S9600PLRTRMTC

Shower Valve Trim

S9601PTRMTC

Shower Trim

S9601PLRTRMTC

Shower Trim

S9602PTRMTC

Tub/Shower Trim

S9602PLRTRMTC

Tub/Shower Trim

S9603PLRTRMTC

Hand Shower Trim

S9604PLRTRMTC

Tub/Hand Shower Trim

S9606PLRTRMTC

Tub/Shower/Hand Shower Trim

S9608PLRTRMTC

Shower/Hand Shower Trim

Warranty

S-9600-P-TRM

S9600PTRMTC

S-9602-P-TRM

S9602PTRMTC

TA-10T-12A

S-9600-PLR-TRM

S9600PLRTRMTC

S-9601-P-TRM

S9601PTRMTC

S-9601-PLR-TRM

S9601PLRTRMTC

S-9602-PLR-TRM

S9602PLRTRMTC

S-9603-PLR-TRM

S9603PLRTRMTC

S-9606-PLR-TRM

S9606PLRTRMTC

S-9604-PLR-TRM

S9604PLRTRMTC

S9608PLRTRM

S9608PLRTRMTC

Summary of content (8 pages)

PAGE 1
Origins® Origins Trim Series Origins Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A S-9600-P-TRM Shower Valve Trim S9600PTRMTC Shower Valve Trim S-9600-PLR-TRM Shower Valve Trim S9600PLRTRMTC Shower Valve Trim S-9601-P-TRM Shower Trim S9601PTRMTC Shower Trim S-9601-PLR-TRM Shower Trim S9601PLRTRMTC Shower Trim S-9602-P-TRM Tub/Shower Trim S9602PTRMTC Tub/Shower Trim S-9602-PLR-TRM Tub/Shower Trim
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (3mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions FIGURE 2 A N WOOD BLOCKING T B O Measurements A B C D E P F G C H D I Q E F I G J U V R K L H M N O P Q R S T U V W X Y Z J K L M S FLOOR W Y Z X Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater.
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system.
PAGE 4
7.
PAGE 5
8. Installation - Shower Valve Trim 1) Place diverter/volume control handle into slot in shower escutcheon (FIGURE 8.1). FIGURE 8.1 FIGURE 8.2 FIGURE 8.3 FIGURE 8.4 2) Secure large shower escutcheon to Temptrol pressure balancing valve using mounting screws. Guide handle into control port on valve body (FIGURE 8.2). 3) Install dome cover by turning clockwise (FIGURE 8.3). 4) A: Install 'P' handle to shower valve. Secure with set screw. Install plug button (FIGURE 8.4).
PAGE 6
11. Installation - Slide Bar Assembly 1) R emove slide bar ends from slide bar flanges. Using flanges as a guide, drill 1/8" pilot holes into studs or wood blocking. With slide bar in position, secure to wall using screws. Attach slide bar ends to bar flanges (FIGURE 11.1). FIGURE 11.5 FIGURE 11.1 1 2 2) R emove screw cap from slide mechanism (FIGURE 11.2). 3 3) R emove wand holder from slide mechanism (FIGURE 11.3). N1 4) R emove lever handle from slide mechanism (FIGURE 11.4).
PAGE 7
12. Operation (Temperature Control) 1) Turn shower handle counterclockwise approximately 1/4 turn to put valve in cold position (FIGURE 12.1). FIGURE 12.2 FIGURE 12.1 FIGURE 12.3 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 12.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 12.3). 13.
PAGE 8
16. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.