Installation Sheet

ManualsBrandsSymmons ManualsPlumbingTemptrol Collection C-96-400-B30-V-X Wall Mounted Tub and Handshower Trim Set with Integral Service Stops and Lever Handle in Polished Chrome

INSTALLATION OF:

SHOWER SYSTEMS AND

TUB/SHOWER SYSTEMS

Tools required for installation of this

product are: Phillips screw driver, tubing

cutter, Teﬂon tape, soldering equipment,

adjustable wrench and channel-lock pliers.

1. Install piping and ﬁttings with valve

body as shown in Figure 2 or 3.

IMPORTANT: Valve rough-in is 2”

+/- 1/2” from CENTERLINE OF

SUPPLIES TO FACE OF FINISH

WALL. Install so that line indicated on

rough-in plaster shield (T-229) on valve

is ﬂush with ﬁnish wall as shown in

Figure 1 (see Figure 5 for ﬁberclass wall

installation).

FIGURE 1

ðøﬂøÍF^œþ½½^ðþ⁄¨

p‘ omp‘

soﬁﬁ

Í˙˝˝½ø¨Í

‹

f¶kppwg

r‘^fonoﬁﬁg^›øﬂ

r^omp‘^foorﬁﬁg^›þÓ

Tub/Shower System (Figure 2)

Model C-96-2

Pipe shower head from outlet marked

“S” and to tub spout from outlet

marked “T”. The valve in this system has

a built-in choke for use with a diverter

spout. The built-in choke is designed so

that it cannot be subject to any back

pressure, other than is imposed by the

spout supplied with this package. DO

NOT SUBSTITUTE OTHER OUTLET

ACCESSORIES FOR THE TUB SPOUT

(SUCH AS HOSE AND SPRAY,

SHOWER HEAD, BODY SPRAY,

LEDGE SPOUTS, ETC.) OR ANY

PIPE ADAPTER OR ADDITIONAL

FITTINGS (SUCH AS PEX, ETC.)

THAT CAN CAUSE BACK PRESSURE

THROUGH THE VALVE. Install HOT

on left and COLD on right according to

valve markings.

Tub or Shower System (Figure 3)

Model C-96-1

Shower System: Pipe shower head

from outlet marked “S”. Install either

the included copper sweat or 1/2”-14

NPT plug (pipe sealer required) into the

outlet marked “T” (see ﬁgure 3A).

Tub only System: Pipe tub spout

from outlet marked “T”. Install either

the included copper sweat or 1/2”-14

NPT plug (pipe sealer required) into the

outlet marked “S” (ﬁgure 3A).

2. When ﬁnishing tile wall REMOVE (pull

off; don’t turn) ENTIRE PROTECTIVE

ROUGH-IN SHIELD and FILL AREA

AROUND VALVE BODY WITH GROUT

OR PLASTER.

3. TURN ON HOT AND COLD SUPPLIES,

valve will not operate unless both hot

and cold water are turned on.

6 1/2"

164m m

4 5/8"

116m m

approx.

40"

1016m m

7 3/8"

187m m

102 m m m in.

less st ops

5 1/2"

140 m m m in.

w ith st ops

51m m

2 1/4"

58m m

FIGURE 2

Model: C-96-2 Tub/Shower System

Sufﬁx SS: Slip-on type spout

2 1/4"

58m m

2 3/8"

67m m

WARNING: This product can expose you

to chemicals including lead,

which is known to the state of

California to cause cancer, birth

defects, or other reproductive

harm. For more information,

go to www.P65Warnings.ca.gov.

Summary of content (6 pages)

PAGE 1
INSTALLATION OF: SHOWER SYSTEMS AND TUB/SHOWER SYSTEMS FIGURE 2 Model: C-96-2 Tub/Shower System Tools required for installation of this product are: Phillips screw driver, tubing cutter, Teflon tape, soldering equipment, adjustable wrench and channel-lock pliers. 4 5/8" 116m m 1. Install piping and fittings with valve body as shown in Figure 2 or 3. IMPORTANT: Valve rough-in is 2” +/- 1/2” from CENTERLINE OF SUPPLIES TO FACE OF FINISH WALL.
PAGE 2
4. Tighten packing nut (T-17) for positive frictional resistance to handle turn throughout adjustment cycle and at shut-off position. Check valve cap, packing nut, all valve, pipe and fitting connections for leaks. FIGURE 3 Model: C-96-1 Shower System 5. SET LIMIT STOP SCREW AS DIRECTED AFTER “IMPORTANT” IN BOLD TYPE ON PAGE ONE. Attach dome cover (T-19) onto packing nut (T-17) and secure with lock nut (T-20). 4 5/8" 116m m 6 1/2" 164m m 6.
PAGE 3
BACK TO BACK INSTALLATION To simplify piping on back to back installations use one standard valve (hot on left, cold on right) and one with reverse coring (hot on right, cold on left) as shown in Figure 6 and 7. Order reverse core valve by adding the suffix REV-X after the plate number. (e.g. C-96-2-REV-X Temptrol® tub and shower unit with reverse coring.
PAGE 4
INDIVIDUAL PARTS DF-9B DF-9CVP RC-14X SC-15A T-1 T-2 T-3 T-5 T-6 T-7 T-8 TA-10 T-11 T-12A T-16 T-17 T-19BR T-20 T-34 T-35A T-35B T-52A T-55B T-55C T-169 T-177 T-229 COMPOSITE PARTS Escutcheon screws (2) Escutcheon screws (vandal-resistant) (2) Single blade lever handle Set screw Hot renewable seat Cold seat O-ring Cold renewable seat Hot washer screw Hot washer Cold washer retainer Cold washer Flow control spindle Cap gasket Cap assembly Packing, O-ring and washers Packing nut Dome cover Lock nut Limit st
PAGE 5
SERVICE TEMPTROL SERIES SERVICE INSTRUCTIONS 1. 6. Inspect top surfaces of hot and cold 1. Shut Shut off off water watersupply supplyto tovalve. valve or close retainer (remove retainer with channel seats and replace if necessary. Impor 2. Remove handle plug driver buttonstops (T-33)byand valve integral screw turnlockWhen pliers). tant: replacing hot and cold handle (T-31). direction after step 3. ing in clockwise 6. seats, Inspect top replace surfacesboth of hot and cold always seats. Even if 3.
PAGE 6
Temptrol® Commercial Series Pressure-Balancing Mixing Valve for Shower or Tub/Shower Application INSTALLATION, OPERATION & SERVICE INSTRUCTIONS Symmons valves and shower heads comply to all known standards, codes and specifications: CSA B-125, ANSI A112.18.1M, ASSE 1016, EPA ‘92 etc. Symmons shower heads are equipped with a 2.5 GPM (9.5 L/min) water and energy saving flow restrictor.