Installation Sheet

ManualsBrandsSymmons ManualsKitchen FaucetsOrigins 2.2 GPM Widespread Kitchen Faucet - Includes Sidespray and Escutcheon

Installation

Caution: Be sure to turn off hot and cold water supplies before

installing or servicing faucet.

Step 1 If installing model with hose and spray, install hose

guide into hole in sink (normally the far right hole on four

hole sink). From underneath sink place washer then nut over

hose guide and secure to sink. Insert hose through hose guide

and up through middle hole from le in sink. Loosely install

the anchor bar (KN-23), spacer (KN-26) and nut (L-36) on the

mounting bolts and place gasket on base of faucet. From above

sink attach hose securely to nipple on base of faucet.

Step 2 Align faucet to sink by matching underside arrow

and word “FRONT” on base plate (KN-33) with front of sink.

Without straightening copper supplies insert through center

hole of sink and anchor bar/spacer/nut assemblies through

holes in sink. Secure faucet to sink by tightening nuts from

underside. (If sink surface is uneven use putty or sealant to

make proper seal under base.)

Step 3 Carefully straighten copper supplies to avoid kinking

tubing. Connect hot supply to le tube and cold supply to right

tube using appropriate connectors.

Step 4 It is very important to thoroughly ush the supply

lines to prevent foreign matter, i.e. copper chips, sand, stones,

etc. from damaging the sealing surfaces of cartridge. Remove

aerator and turn valve handle on to full cold position, open cold

supply. Without closing, turn handle to full hot and open hot

supply. Let water run in hot only and cold only positions long

enough to ush supply lines thoroughly. If equipped with a hose

and spray, direct spray head into sink and activate spray. Shut

o faucet and replace aerator. Check for leaks.

Step 5 e handle limit stop can be set to limit handle turn

to the hot position. e limit mechanism is factory set to allow

full handle travel. To adjust the limit stop, turn handle to the

full hot position and li handle to open faucet approximately

half way to obtain a smooth ow for correct initial temperature

measurement.

Step 6 If when faucet is on and in full hot position and water

is too hot, shut water o, remove plug button (KN-157), loosen

set screw (L-22) and remove handle (KN-3RB or KN-3BRB),

li limit stop using a small at head screw driver and rotate

clockwise to lower temperature. If water is not hot enough,

rotate counter clockwise (See Figure 1 on reverse side). Aer

correct temperature is achieved, reattach handle, reversing

procedure above.

Cartridge Replacement (KN-4)

Step 1 Remove plug button (KN-157), loosen set screw (L-22)

and remove handle (KN-3RB or KN-3BRB).

Step 2 Engage tabs in cartridge wrench (LN-34) with slots in

compression ring (KN-2) and use screwdriver in wrench holes or

pliers on wrench and turn counter clockwise until compression

ring engages with cap (KN-1). Continue turning counter

clockwise so that cap/ring assembly is removed from the body

(KN-11).

Step 3 Remove cartridge and o-ring seal (KN-4).

Step 4 Install new cartridge while taking care to maintain

position of the o-ring seal at the base of the cartridge. Match

posts in base of cartridge with alignment holes in adapter plate

during assembly.

Step 5 Reassemble faucet in reverse fashion. Thread cap onto

body firmly by hand. Do not use a wrench which may damage

the finish. Tighten compression ring (KN-2) finger tight using

the wrench (LN-34) then 1/4 to 1/2 turn further. Set hot water

limit stop in accordance with installation step 6 above.

Diverter replacement (KN-169)

1. Follow cartridge replacement steps 1 through 5 above.

2. Remove retaining ring (K-44) with 3/8” hex key wrench.

3. Remove diverter (K-43) and o-ring (K-46).

4. Grease diverter o-ring and install into body.

5. Press diverter into o-ring and body.

6. Replace retaining ring.

Kitchen Faucet S-23 Series

Installation and Service Instructions

Origins

10-1/8"

257mm

7-1/2"

191mm

203mm

7-1/4"

184mm

152mm

6-1/4"

159mm

1/2"- 13mm

with spacer

1-1/4"- 32mm

without spacer

spacer

optional 1/2-14

NPT tting

5 1/4

133mm

8-3/4"

222mm

10-7/8"

276mm

1/4-20" UNC

Dimensions Origins Kitchen Faucet, S-23

Note:

Dimensions subject to change without notice.

Summary of content (4 pages)

PAGE 1
Origins ® Kitchen Faucet S-23 Series Installation and Service Instructions Installation Caution: Be sure to turn off hot and cold water supplies before installing or servicing faucet. Step 1 If installing model with hose and spray, install hose guide into hole in sink (normally the far right hole on four hole sink). From underneath sink place washer then nut over hose guide and secure to sink. Insert hose through hose guide and up through middle hole from left in sink.
PAGE 2
Parts Assembly Origins Kitchen Faucet, S-23 Series K-41/42* K-43 K-44 K-46 KN-1* KN-2 KN-3RB* KN-3BRB* KN-4 KN-11 ASSY Hand spray and holder Diverter valve Repair Retainer ring use only O-ring Valve cap Compression ring Solid Handle Loop Handle Cartridge Supply body assembly with diverter KN-11A ASSY Supply body assembly without diverter KN-19A Spacer KN-20 O-ring (2) KN-23 Anchor bar (2) KN-26 Mounting spacer (2) KN-30* Escutcheon KN-30A* Escutcheon with hand spray hole KN-33 Base plate KN-118 Gasket KN-1
PAGE 3
Origins ® Kitchen Faucet S-23-BH Series Installation and Service Instructions Installation Caution: Be sure to turn off hot and cold water supplies before installing or servicing faucet. Step 1 If installing model with hose and spray, install hose guide into hole in sink (normally the far right hole on four hole sink). From underneath sink place washer then nut over hose guide and secure to sink. Insert hose through hose guide and up through middle hole from left in sink.
PAGE 4
Parts Assembly Origins Kitchen Faucet, S-23-BH Series K-41/42* K-43 K-44 K-46 KN-1* KN-2 KN-3RB* KN-3BRB* KN-4 KN-11 ASSY Hand spray and holder Diverter valve Repair Retainer ring use only O-ring Valve cap Compression ring Solid Handle Loop Handle Cartridge Supply body assembly with diverter KN-11A ASSY Supply body assembly without diverter KN-19A Spacer KN-20 O-ring (2) KN-23 Anchor bar (2) KN-26 Mounting spacer (2) KN-30* Escutcheon KN-30A* Escutcheon with hand spray hole KN-33 Base plate KN-118 Gasket K