Installation Guide

ManualsBrandsSymmons ManualsPlumbingDia Single-Handle Wall-Mounted Tub and Shower Trim Kit in Matte Black - 1.5 GPM (Valve not Included)

Dia

Model Numbers

Dia Trim Series

Dia Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

S-3500-CYL-B-TRM

Shower Valve Trim

S-3501-CYL-B-TRM

Shower Trim

S-3502-CYL-B-TRM

Tub/Shower Trim

S-3504-H321-V-CYL-B-TRM

Tub/Hand Shower Trim

S3508BTRM

Shower/Hand Shower Trim

TRIM, TA-10, T-12A

S3500CYLBTRMTC

Shower Valve Trim

S3501CYLBTRMTC

Shower Trim

S3502CYLBTRMTC

Tub/Shower Trim

S3504H321CYLBTRMTC

Tub/Hand Shower Trim

S3508BTRMTC

Shower/Hand Shower Trim

S-3500-CYL-B-TRM

S3500CYLBTRMTC

S-3501-CYL-B-TRM

S3501CYLBTRMTC

S-3502-CYL-B-TRM

S3502CYLBTRMTC

S3508BTRM

S3508BTRMTC

S-3504-H321-V-CYL-B-TRM

S3504H321CYLBTRMTC

TA-10T-12A

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Go to www.symmons.com/register to register your

Symmons product.

Warranty

Summary of content (8 pages)

PAGE 1
Dia® Dia Trim Series Dia Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A S-3500-CYL-B-TRM Shower Valve Trim S3500CYLBTRMTC Shower Valve Trim S-3501-CYL-B-TRM Shower Trim S3501CYLBTRMTC Shower Trim S-3502-CYL-B-TRM Tub/Shower Trim S3502CYLBTRMTC Tub/Shower Trim S-3504-H321-V-CYL-B-TRM Tub/Hand Shower Trim S3504H321CYLBTRMTC Tub/Hand Shower Trim S3508BTRM Shower/Hand Shower Trim S3508BTRMTC Shower/Hand
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (3mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions Measurements FIGURE 2 A A B C B D D E F G H C I J K L E M F G N O P K J H I FLOOR O L N M P Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater. 3) All dimensions measured from nominal rough-in (see M as reference).
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system.
PAGE 4
7.
PAGE 5
8. Installation - Shower Valve Trim 1) Secure large mounting plate to Temptrol pressure balancing valve using mounting screws (FIGURE 8.1). FIGURE 8.1 FIGURE 8.2 FIGURE 8.3 FIGURE 8.4 2) Place diverter/volume control handle into slot in shower escutcheon (FIGURE 8.2). 3) Secure large shower escutcheon to mounting plate. Guide handle into control port on valve body. Tabs should snap in place (FIGURE 8.3). 4) Install dome cover by turning clockwise (FIGURE 8.4). 5) Install handle to shower valve.
PAGE 6
10. Installation - Slide Bar Assembly 1a) D ry Wall Option: Remove upper and lower caps from slide bar brackets. Place slide bar into desired position. Using brackets as a guide, carefully drill 3/16" holes into wall. Remove slide bar and install anchors. Note: Slide bar holes and bracket holes must be aligned before drilling. Before drilling bottom hole, make sure slide bar is plumb (FIGURE 10.1A). 1 3 1 1b) S tud Option: Remove upper and lower caps from slide bar brackets.
PAGE 7
11. Operation (Temperature Control) 1) Turn shower handle counter-clockwise approximately 1/4 turn to put valve in cold position (FIGURE 11.1). FIGURE 11.1 FIGURE 11.2 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 11.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 11.3). 12.
PAGE 8
14. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.