Installation Guide

ManualsBrandsSymmons ManualsBathDuro 1-Handle Tub and Shower Faucet Trim in Chrome (Valve Not Included)

Tub-Shower Systems S-3600, S-3601, S-3602 Series

Installation and Service Instructions

Duro™

1 2 3 4

Handle kit

RTS-002

Tub spout

067

COLD

supply inlet

HOT

supply inlet

Showerhead

362SH

Protective valve shield (not shown) T-176

Temp Limit

stop screw

Escutcheon

mounting plate

Note: Piping, ttings and tools are not included.

Actual plumbing should be determined and

installed by a licensed plumber.

Mounting

plate, T-177

Arm and ange

300S

Dome

cover

Tools & Materials

Volume control handle

or diverter handle

RTS-004

Temptrol

Control Valve

S-4001-BODY

S-4001-X-BODY

S-4002-BODY

S-4002-X-BODY

Model Series

S-3602

S-3602-X

S-3602-TRM

Model Series

S-3601

S-3601-X

S-3601-TRM

S-3602

S-3602-X

S-3602-TRM

Model Series

S-3600

S-3600-X

S-3600-TRM

S-3601

S-3601-X

S-3601-TRM

S-3602

S-3602-X

S-3602-TRM

S-3600TS

S-3600TS-X

Model Series

S-3600

S-3600-X

S-3600TS

S-3600TS-X

S-3601

S-3601-X

S-3602

S-3602-X

Screwless escutcheon kit

RTS-003

1/8"

Visual Guide

Duro Tub-Shower Systems S-3600, S-3601, S-3602 Series

Model Number Series

S-3602 .......... Tub-Shower System

S-3602-X ...... Valve includes stops

S-3602-TRM . Trim only

S-3601 .......... Shower System

S-3601-X ...... Valve includes stops

S-3601-TRM . Trim only

 Need Help?

Symmons customer service:

(

800) 796-6667, (781) 848-2250

customerservice@symmons.com

Mon - Fri 7:30 am - 7:00 pm EST



www.symmons.com/service

• Technical help

• Product information

• Warranty policy

S-3600 .......... Shower Valve System

S-3600-X ...... Valve includes stops

S-3600-TRM . Trim only

S-3600TS ..... Tub-Shower Valve Sys.

S-3600TS-X .. Valve includes stops

Summary of content (6 pages)

PAGE 1
Duro™ Tub-Shower Systems S-3600, S-3601, S-3602 Series Installation and Service Instructions  Model Number Series S-3602........... Tub-Shower System S-3602-X....... Valve includes stops S-3602-TRM.. Trim only S-3600........... Shower Valve System S-3600-X....... Valve includes stops S-3600-TRM.. Trim only S-3601........... Shower System S-3601-X....... Valve includes stops S-3601-TRM.. Trim only S-3600TS...... Tub-Shower Valve Sys. S-3600TS-X...
PAGE 2
Installation Instructions Rough-in Installation Control valve assembly, piping and fittings (Note: Illustrations below show valve model without stops) Reference as required: Page Visual guide.....................................1 Dimensions illustration.................4 1) Determine wall thickness ■■ Determine type of wall and wall thickness where valve will be mounted. ■■ Consider whether to use mounting plate by reviewing figure 2 below. ■■ Skip ahead to Step 3 if mounting plate is not used.
PAGE 3
7) Flush system, check for leaks 2) Attach escutcheon 5) Attach showerhead ■■ Turn valve to the warm position and run for a few minutes. ■■ If system is dirty, remove valve spindle in center of valve to ensure proper flushing. (See service instructions.) ■■ Check for leaks around valve assembly and all pipe fittings.
PAGE 4
Dimensions Duro Tub-Shower Systems, S-3600, S-3601, S-3602 Series Model Series S-3601 S-3601-X S-3602 S-3602-X finished wall 2-1/2" dia (64 mm) 6" (151 mm) 1/2"-14 NPT 4-5/8" (118 mm) Model Series S-3600 S-3600-X S-3600TS S-3600TS-X S-3601 S-3601-X S-3602 S-3602-X approx 77" (1956 mm) showerhead supply outlet Finished wall to pipe centerline 2-3/8" ± 1/2" (60 mm ±13 mm) *see note (2) 5/8" (16 mm) Finished wall to rear of valve 3-1/2" ± 1/2" (89 mm ±13 mm) Wall cutout hole size 3-1/2" (89 mm) min 4
PAGE 5
Parts Assembly Temptrol Shower & Tub-Shower Control Valves ■ S-4002-BODY......Tub-Shower valve ■ S-4001-BODY......Shower valve ■ S-4001-X-BODY..Shower valve w/stops ■ S-4002-X-BODY..
PAGE 6
Trouble Shooting Chart Problem Cause Solution Valve will not pass water. Both hot and cold water supplies are not turned on. Turn on both supplies. Valve will not operate unless both hot and cold water pressure is on. Valve leaks when shut off. Hot and cold washers are worn or foreign matter (dirt, chips) is lodged between washers and seat surfaces. 1) Replace washers using control spindle washer repair kit, p/n TA-9. 2) Replace hot & cold seats using hot/cold seat repair kit, p/n TA-4.