Installation Guide

ManualsBrandsSymmons ManualsMixing ValvesAllure Tub/Shower Pressure Balancing Valve in Chrome

Model Numbers Speciﬁcation

Options/Modiﬁcations

Tub/shower trim with lever handle and secondary

diverter lever handle includes non-diverter tub spout

and 3 mode showerhead with standard 2.5 gpm

(9.5 L/min) ow restrictor. Shower trim with lever handle

and secondary volume control lever handle includes

all of the above less non-diverter tub spout. Valve trim

with lever handle and secondary lever handle includes

valve trim only. Components made from metal and

nonmetallic materials plated in standard polished

chrome nish.

Allura

Trim Series

Operation & Maintenance Manual

S-4700-TRM, S-4701-TRM, S-4702-TRM

S-4700-TRM

Valve Trim

Compliance

-1.5

1.5 gpm (5.7 L/min) ﬂow restrictor

-2.0

2.0 gpm (7.6 L/min) ﬂow restrictor

-LAM

Metal ﬁnish insert handle

-LR

Lever handle

S-4701-TRM

Shower Trim

Note: Append appropriate -sufx to model number.

-STN

Satin Nickel ﬁnish

-ASME A112.18.1; CSA B125.1

S-4702-TRM

Tub/Shower Trim

-SS

Slip spout on any tub and shower unit

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

For California Residents

WARNING: This product contains chemicals known to

the State of California to cause cancer, birth defects, or

other reproductive harm.

Summary of content (5 pages)

PAGE 1
S-4700-TRM, S-4701-TRM, S-4702-TRM Allura® Trim Series Operation & Maintenance Manual Model Numbers S-4700-TRM Valve Trim S-4701-TRM Shower Trim S-4702-TRM Tub/Shower Trim Options/Modifications Specification Tub/shower trim with lever handle and secondary diverter lever handle includes non-diverter tub spout and 3 mode showerhead with standard 2.5 gpm (9.5 L/min) flow restrictor. Shower trim with lever handle and secondary volume control lever handle includes all of the above less non-diverter tub spout.
PAGE 2
Dimensions A A B C D E B F G H I J D K I C H G J K F E Floor L M N Notes: 1) All dimensions measured from nominal rough-in (see K as reference). 2) Dimensions subject to change without notice. 2 L M N Measurements Ø 2 1/2”, 64 mm 6 3/4”, 172 mm Ø 7”, 178 mm Ref. 77”, 1956 mm 2 1/2", 64 mm Ref. 32”, 813 mm (S-4702-TRM) Ref.
PAGE 3
Parts Breakdown Replacement Parts C A J F D K H Description Part Number A Showerhead 4-143 C D E F G H Shower Arm (flange included) Flange Plug Button Handle Screw Star Washer Handle Dome Cover I J K* Dial Mounting Screws Shower Escutcheon L Secondary Lever Handle T-139 M Tub Spout 060 B B G Item 300S 430SS RTS-026 T-19 T-131A (S-4702-TRM S-4700-TRM) T-131B (S-4701-TRM) Notes: 1) Append -STN to part number for Satin Nickel finish. 2) Append -1.5 or -2.
PAGE 4
Installation Note: For valve body installation, please see valve body manual. 3) Install dome cover (H) to valve by turning clockwise. 5) I nstall tub spout (M) to pipe fitting. Turn clockwise to secure. 1) Install secondary integral diverter (L) into shower escutcheon (K). 1 1 M 2 H 2 K L 4) Install handle (G) to valve and secure with screw (E) and star washer (F). Attach plug button (D) to handle. 1 2) Install shower escutcheon (k) to shower valve. Secure with two screws (J).
PAGE 5
Operation & Maintenance Temperature Control Diverter Control 1) Turn shower handle counterclockwise approximately 1/4 turn to put valve in cold position. 1) Turn diverter left for tub spout operation. 2) Turn diverter right for showerhead operation. 2) Turn shower handle counterclockwise approximately 1/2 turn to put valve in warm position. 3) Turn shower handle counterclockwise approximately 3/4 turn to put valve in hot position. Troubleshooting Chart Finish is spotting.