Installation Guide

ManualsBrandsSymmons ManualsPlumbingIdentity 1-Handle Tub and Shower Faucet Trim Kit with Diverter Lever in Satin Nickel (Valve Not Included)

Identity

™

Model Numbers

S-6700, S-6700TS, S-6701, S-6702

Operation & Maintenance Manual

Speciﬁcation

Modiﬁcations

Note: Append appropriate -sufx to model number.



S-6700

Identity Shower System



S-6700TS

Identity Tub/Shower System



S-6701

Identity Shower System



S-6702

Identity Tub/Shower System

S-6700

Shower system powered by the Temptrol

pressure-

balancing valve with integrated volume control. Valve body

includes adjustable stop screw to limit handle turn.

S-6700TS

Tub/shower system powered by the Temptrol

pressure-

balancing valve with integrated diverter. Valve body

includes adjustable stop screw to limit handle turn.

S-6701

Shower system powered by the Temptrol

pressure-

balancing valve. Features adjustable stop screw to

limit handle turn, integrated volume control, 1 mode

showerhead with easy to clean rubber nozzles and

standard 2.5 gpm (9.5 L/min) ow restrictor.

S-6702

Tub/shower system powered by the Temptrol® pressure-

balancing valve. Features adjustable stop screw to limit

handle turn, integrated diverter, non-diverter tub spout, 1

mode showerhead with easy to clean rubber nozzles and

standard 2.5 gpm (9.5 L/min) ow restrictor.

Components made from metal and nonmetallic materials,

plated in standard polished chrome nish.



-1.5 1.5 gpm (5.7 L/min) ﬂow restrictor



-2.0 2.0 gpm (7.6 L/min) ﬂow restrictor



-143 3 mode showerhead



-145 5 mode showerhead



-231 2 mode showerhead



-CHKS Integral check stops - for use in

installations where a positive shut-off

device is used downstream of mixing valve



-IPS

1/2" female IPS connections



-L/HD

Less showerhead



-LP Loop handle



-LR Lever handle



-OP 13" oval plate



-REB-TRM

Rebuild trim kit



-REV Reverse coring, hot on right, cold on

left, for back to back installations



-SS Slip spout on any tub/shower unit



-STN Satin Nickel ﬁnish



-TRM Trim only, valve not included



-X Integral service stops - allows water

shutoff at valve for service

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Compliance

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

Certied by

CSA Group

For California Residents

WARNING: This product contains chemicals known to the

State of California to cause cancer, birth defects, or other

reproductive harm.

Summary of content (15 pages)

PAGE 1
Identity™ S-6700, S-6700TS, S-6701, S-6702 Operation & Maintenance Manual Model Numbers Specification  S-6700 S-6700 Shower system powered by the Temptrol® pressurebalancing valve with integrated volume control. Valve body includes adjustable stop screw to limit handle turn.
PAGE 2
Dimensions Measurements N A A B C D E B O F G H I J K L D C F E P G H J I K L Q M FLOOR Notes: 1) All dimensions measured from nominal rough-in (see I as reference). 2) Dimensions subject to change without notice. 2 M N O P Q 5-7/8", 149 mm 4-5/8", 117 mm 3-1/2", 89 mm 2-7/8", 73 mm Ref. 77", 1956 mm Shower Valve Hole Size Min. Ø 3", 76 mm Max.
PAGE 3
Parts Breakdown Replacement Parts C B A I G F H HOT Water Supply H E Description Part Number A Showerhead 672SH* B C D E Shower Arm Flange Handle Set Screw F Dome Cover T-19* G H I Shower Escutcheon Kit (S-6700TS, S-6702) S-6700TS-ESC* (S-6700, S-6701) S-6700-ESC* J Secondary Handle RTS-280* K Tub Spout 060* 300S* RTS-281* *Note: Append -STN to part number for Satin Nickel finish.
PAGE 4
Installation Note: For valve body installation, please see valve body manual. 4) Install dome cover (F) to shower valve by turning clockwise. 7) Attach shower arm (B) and flange (C) to vertical shower pipe. Turn clockwise to tighten. 1) Install shower mounting plate (I) to shower valve. Secure with two screws (H). C I F 2 H 2 3 2 1 H 1 1 B 1 5) Install handle (D) to shower valve. Secure handle with set screw (E). 8) Install showerhead (A) to shower arm (B).
PAGE 5
Operation (Temperature Control) 1) Turn shower handle counterclockwise approximately 1/4 turn to put valve in cold position. 2) Turn shower handle counterclockwise approximately 1/2 turn to put valve in warm position. 3) Turn shower handle counterclockwise approximately 3/4 turn to put valve in hot position. Operation (Diverter Control for S-6700TS, S-6702) 1) Turn diverter handle left for tub spout operation. 2) Turn diverter handle right for showerhead operation.
PAGE 6
Identity™ S-6700, S-6700TS, S-6701, S-6702 Manual de funcionamiento y mantenimiento Números de modelo Especificación  S-6700 S-6700 Sistema para ducha Identity  S-6700TS Sistema para ducha con válvula compensadora de presión Temptrol® y control de caudal integrado. El cuerpo de la válvula incluye un tornillo con tope ajustable para limitar el giro de la manija.
PAGE 7
Dimensiones Medidas N A A B C D E B O F G H I J K D C F E L P G H J I K L Q M PISO Notas: 1) Todas las dimensiones tomadas desde el empotrado (ver I para referencia). 2) Las dimensiones están sujetas a cambios sin previo aviso. 7 M N O P Q 5-7/8", 149 mm 4-5/8", 117 mm 3-1/2”, 89 mm 2-7/8", 73 mm Ref. 77”, 1956 mm Tamaño de los orificios de la válvula para ducha Mín. Ø 3”, 76 mm Máx.
PAGE 8
Desglose de piezas Repuestos C B A Cabezal de ducha 672SH* B C Brida del brazo de la ducha Manija Tornillo de presión Cubierta del domo RTS-281* Juego de escudete para la ducha (S-6700TS, S-6702) S-6700TSESC* (S-6700, S-6701) S-6700-ESC* G H I H Suministro de agua CALIENTE H D K E Número de la pieza F I F Descripción D E A G Artículo Manija secundaria Surtidor para bañera J Suministro de agua FRÍA J K 300S* T-19* RTS-280* 060* *Nota: Anexar -STN al número de pieza para acabado
PAGE 9
Instalación Nota: Para instalar el cuerpo de la válvula, vea el manual de la válvula. 1) Instale la placa de montaje (I) a la válvula de la ducha. Sujétela con dos tornillos (H). 4) Instale la cubierta del domo (F) a la válvula de la ducha girándola en el sentido de las manecillas del reloj. C B 1 2 3 1 F 2 2 H 1 1 I H 7) Una el brazo de la ducha (B) y la brida (C) al tubo vertical de la ducha. Gire en el sentido de las manecillas del reloj para apretar.
PAGE 10
Funcionamiento (Control de temperatura) 1) Gire el mango de la ducha 1/4 de vuelta en sentido contrario a las manecillas del reloj para colocar la válvula en la posición de agua fría. 2) Gire el mango de la ducha 1/2 de vuelta en sentido contrario a las manecillas del reloj para colocar la válvula en la posición de agua tibia. 3) Gire el mango de la ducha 3/4 de vuelta en sentido contrario a las manecillas del reloj para colocar la válvula en la posición de agua caliente.
PAGE 11
Identity™ S-6700, S-6700TS, S-6701, S-6702 Manuel d'utilisation et d'entretien Numéros de modèle Spécifications  S-6700 S-6700 Système de douche Identity  S-6700TS Système de baignoire/douche Identity  S-6701 Système de douche Identity  S-6702 Système de baignoire/douche Identity Modifications Système de douche alimenté par la vanne à pression autorégularisée Temptrol® avec contrôleur de volume intégré.
PAGE 12
Dimensions Mesures N A A B C D E B O D C F E P G H J 5-7/8 po, 149 mm 4-5/8 po, 117 mm 3-1/2 po, 89 mm 2-7/8 po, 73 mm Réf. 77 po, 1956 mm Taille du trou pour la vanne de douche F Min. Ø 3 po, 76 mm Max. Ø 4 po, 102 mm G 3-1/2 po, 89 mm H 7/8 po, 22 mm Robinetterie brute I 2-3/8 po ± 1/2 po, 60 mm ± 13 mm J 12 po, 305 mm Raccord NPT 1/2 po mâle doit K faire saillie de 4 po (102 mm) du mur fini S-6700, S-6700TS Réf. 32 po, 813 mm L S-6700, S-6701 Réf.
PAGE 13
Liste des pièces C Article B A B C D E A F I G G H I H J F K Alimentation en eau CHAUDE H D J Alimentation en eau FROIDE Pièces de rechange Numéro Description de pièce Pomme de douche Bras et bride de douche Assemblage Vis de pression Couvercle en dôme Douche Ensemble rosace Poignée secondaire Bec de baignoire Remarques : 1) Appliquez un joint de silicone autour du périmètre de la garniture de douche montée en alignement avec le mur fini (moins les plaques et les supports de fixation).
PAGE 14
Installation Remarque : Pour l'installation du corps de vanne, veuillez consulter le manuel du corps de vanne. 4) Installez le couvercle en dôme (F) à la vanne de douche en tournant dans le sens des aiguilles d'une montre. 7) Attachez le bras de douche (B) et la bride (C) au tuyau de douche vertical. Tournez dans le sens des aiguilles d'une montre pour serrer. 1) Installez la plaque de montage de la douche (I) à la vanne de douche. Fixez avec deux vis (H).
PAGE 15
Fonctionnement (Contrôle de la température) 1) Tournez la poignée de douche dans le sens contraire des aiguilles d'une montre approximativement 1/4 de tour pour mettre la vanne dans la position d'eau froide. 2) Tournez la poignée de douche dans le sens contraire des aiguilles d'une montre approximativement 1/2 de tour pour mettre la vanne dans la position d'eau tiède.