Specification

ManualsBrandsSymmons ManualsMixing ValvesOrigins Temptrol 1-Handle Shower Valve in Satin Nickel

Origins

™

Model Numbers

Shower Valve

Speciﬁcation Submittal

S-9600-PLR

Shower valve powered by the Temptrol

Pressure

Balancing valve with integrated volume control. Valve

body includes adjustable stop screw to limit handle turn.

Components made from metal and nonmetallic materials

plated in standard polished chrome nish.

Speciﬁcation

Location:

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Compliance

-ASME A112.18.1/CSA B125.1

Modiﬁcations

Note: Append appropriate -sufx to model number.



-X Integral service stops



-CHKS Integral check stops



-IPS

1/2” female IPS connections



-REV Reverse coring for back to back

installations



-LP Loop handle



-B Chrome brass escutcheon



-D Chrome brass dome cover



-VP Vandal proof escutcheon screws



-OP 13” oval plate



-TRM Trim only, valve not included



-STN Satin Nickel ﬁnish



S-9600-PLR

Origins Shower Valve

Reset Form

Summary of content (4 pages)

PAGE 1
Location: Origins™ S-9600-PLR Shower Valve Specification Submittal Model Numbers Specification  S-9600-PLR Shower valve powered by the Temptrol® Pressure Balancing valve with integrated volume control. Valve body includes adjustable stop screw to limit handle turn. Components made from metal and nonmetallic materials plated in standard polished chrome finish.
PAGE 2
Dimensions F A Measurements A B B C C G D D E F G 3 5/8”, 92 mm Shower Valve Hole Size Min. Ø 3”, 76 mm Max. Ø 4”, 102 mm 3 1/2”, 89 mm Rough-in 2 3/8” ± 1/2”, 60 mm ± 13 mm Ref. 42”, 1067 mm Ø 5 3/4”, 146 mm 3 3/8”, 86 mm E FLOOR Notes: 1) All dimensions measured from nominal rough-in (see D as reference). 2) Dimensions subject to change without notice. Symmons Industries, Inc.
PAGE 3
Emplacement: Origins™ S-9600-PLR Système de douche Présentation des spécifications Numéro de modèle Spécification  S-9600-PLR Le système de douche comprend la vanne à pression autorégularisée Temptrol® avec contrôle du volume intégré. Le corps de vanne comprend la vis d’arrêt réglable pour limiter le tournage de la poignée. Les composants sont faits de matériaux métalliques et non métalliques au fini chrome poli standard.
PAGE 4
Dimensions F A Mesures A B B C C G D E F G D 3 5/8 po, 92 mm Taille du trou Min. Ø 3 po, 76 mm Max. Ø 4 po, 102 mm 3 1/2 po, 89 mm Robinetterie brute 2 3/8 po ± 1/2 po, 60 mm ± 13 mm Réf. 42 po, 1067 mm Ø 5 3/4 po, 146 mm 3 3/8 po, 86 mm E FLOOR Remarques: 1) Toutes les dimensions sont mesurées à partir de la robinetterie brute nominale (voir D en référence). 2) Les dimensions sont sujettes à changer sans préavis. Symmons Industries, Inc.