Specification

ManualsBrandsSymmons ManualsMixing ValvesOrigins Temptrol 1-Handle Shower System in Chrome

Origins

™

Model Numbers

Tub/Shower Valve

Speciﬁcation Submittal

S-9600TS-P

Tub/shower valve powered by the Temptrol

Pressure

Balancing valve with integrated diverter. Valve body

includes adjustable stop screw to limit handle turn.

Components made from metal and nonmetallic materials

plated in standard polished chrome nish.

Speciﬁcation

Location:

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Compliance

-ASME A112.18.1/CSA B125.1

Modiﬁcations

Note: Append appropriate -sufx to model number.



-X Integral service stops



-CHKS Integral check stops



-IPS

1/2” female IPS connections



-REV Reverse coring for back to back

installations



-B Chrome brass escutcheon



-D Chrome brass dome cover



-VP Vandal proof escutcheon screws



-OP 13” oval plate



-TRM Trim only, valve not included



S-9600TS-P

Origins Tub/Shower Valve

Reset Form

Summary of content (4 pages)

PAGE 1
Location: Origins™ S-9600TS-P Tub/Shower Valve Specification Submittal Model Numbers Specification  S-9600TS-P Tub/shower valve powered by the Temptrol® Pressure Balancing valve with integrated diverter. Valve body includes adjustable stop screw to limit handle turn. Components made from metal and nonmetallic materials plated in standard polished chrome finish.
PAGE 2
Dimensions F A B Measurements A B C G C D D E F G 2 7/8”, 73 mm Shower Valve Hole Size Min. Ø 3”, 76 mm Max. Ø 4”, 102 mm 3 1/2”, 89 mm Rough-in 2 3/8” ± 1/2”, 60 mm ± 13 mm Ref. 42”, 1067 mm 2 1/8”, 54 mm Ø 5 3/4”, 146 mm E FLOOR Notes: 1) All dimensions measured from nominal rough-in (see D as reference). 2) Dimensions subject to change without notice. Symmons Industries, Inc.
PAGE 3
Emplacement: Origins™ S-9600TS-P Système de baignoire-douche Présentation des spécifications Numéro de modèle Spécification  S-9600TS-P Le système de baignoire-douche comprend la vanne à pression autorégularisée Temptrol® avec déviateur intégré. Le corps de vanne comprend la vis d’arrêt réglable pour limiter le tournage de la poignée. Les composants sont faits de matériaux métalliques et non métalliques au fini chrome poli standard.
PAGE 4
Dimensions F A Mesures A B B C G C D D E F G 2 7/8 po, 73 mm Taille du trou Min. Ø 3 po, 76 mm Max. Ø 4 po, 102 mm 3 1/2 po, 89 mm Robinetterie brute 2 3/8 po ± 1/2 po, 60 mm ± 13 mm Réf. 42 po, 1067 mm 2 1/8 po, 54 mm Ø 5 3/4 po, 146 mm E FLOOR Remarques: 1) Toutes les dimensions sont mesurées à partir de la robinetterie brute nominale (voir D en référence). 2) Les dimensions sont sujettes à changer sans préavis. Symmons Industries, Inc.