Specification

ManualsBrandsSymmons ManualsPlumbingOrigins Temptrol 1-Handle Tub and Shower Faucet Trim Kit in Chrome (Valve Not Included)

Origins

™

Model Numbers

Tub/Shower System

Speciﬁcation Submittal

S-9602-PLR

Tub/shower system powered by the Temptrol

Pressure

Balancing valve. Features adjustable stop screw to limit

handle turn, integrated diverter, non-diverter tub spout, 1

mode showerhead with easy to clean rubber nozzles and

standard 2.5 gpm (9.5 L/min) ow restrictor. Components

made from metal and nonmetallic materials plated in

standard polished chrome nish.

Speciﬁcation

Location:

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Compliance

Modiﬁcations

Note: Append appropriate -sufx to model number.



S-9602-PLR

Origins Tub/Shower System



-1.5 1.5 gpm (5.7 L/min) ﬂow restrictor



-2.0 2.0 gpm (7.6 L/min) ﬂow restrictor



-231 Super showerhead in place of Clear-Flo



-295 Institutional showerhead in place of

Clear-Flo



-SS

Slip spout on any tub/shower unit



-X Integral service stops



-CHKS Integral check stops



-IPS

1/2” female IPS connections



-REV Reverse coring for back to back

installations



-LP Loop handle



-B Chrome brass escutcheon



-D Chrome brass dome cover



-VP Vandal proof escutcheon screws



-OP 13” oval plate



-L/HD Less showerhead



-TRM Trim only, valve not included



-STN Satin Nickel ﬁnish

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

2.0 gpm (7.6 L/min)

Certied by

CSA Group

Reset Form

Summary of content (4 pages)

PAGE 1
Location: Origins™ S-9602-PLR Tub/Shower System Specification Submittal Model Numbers Specification  S-9602-PLR Tub/shower system powered by the Temptrol® Pressure Balancing valve. Features adjustable stop screw to limit handle turn, integrated diverter, non-diverter tub spout, 1 mode showerhead with easy to clean rubber nozzles and standard 2.5 gpm (9.5 L/min) flow restrictor. Components made from metal and nonmetallic materials plated in standard polished chrome finish.
PAGE 2
Dimensions A Measurements J A B C K B L C M E D 6 3/8”, 162 mm 3 1/2”, 89 mm 3 5/8”, 92 mm Shower Valve Hole Size D Min. Ø 3”, 76 mm Max. Ø 4”, 102 mm E Ref. 77”, 1956 mm Rough-in F 2 3/8” ± 1/2”, 60 mm ± 13 mm G Ref. 32”, 813 mm Male 1/2” NPT fitting must H protrude 4” from finished wall I 5 1/2”, 140 mm J Ø 2 1/2”, 64 mm K Ø 2 3/4”, 70 mm L Ø 5 3/4”, 146 mm M 3 3/8”, 86 mm N Ø 2 1/2”, 64 mm F G N H I FLOOR Notes: 1) All dimensions measured from nominal rough-in (see F as reference).
PAGE 3
Emplacement: Origins™ S-9602-PLR Système de baignoire-douche Présentation des spécifications Numéro de modèle Spécification  S-9602-PLR Le système de baignoire-douche comprend la vanne à pression autorégularisée Temptrol®. Figurer la vis d’arrêt réglable pour limiter le tournage de la poignée, un bec de baignoire non-déviateur, 1 pomme de douche avec facile à nettoyer les buses en caoutchouc et réducteur de débit régulier de 2,5 gpm (9,5 L/min).
PAGE 4
Dimensions A Mesures J A B C D E K F G H B L C M E D I J K L M N 6 3/8 po, 162 mm 3 1/2 po, 89 mm 3 5/8 po, 92 mm Taille du trou Min. Ø 3 po, 76 mm Max. Ø 4 po, 102 mm Réf. 77 po, 1956 mm Robinetterie brute 2 3/8 po ± 1/2 po, 60 mm ± 13 mm Réf.