Installation Sheet

ManualsBrandsSymmons ManualsPlumbingOxford Collection S-4202-STN-2.0-TRM Wall Mounted Tub and Shower Trim Set with Lever Handle in Satin Nickel

Oxford

Model Numbers

Oxford Trim Series

Oxford Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

S-4200-TRM

Shower Valve Trim

S-4201-TRM

Shower Trim

S-4202-TRM

Tub/Shower Trim

S-4204-TRM

Tub/Hand Shower Trim

S4208TRM

Shower/Hand Shower Trim

TRIM, TA-10, T-12A

S4200TRMTC

Shower Valve Trim

S4201TRMTC

Shower Trim

S4202TRMTC

Tub/Shower Trim

S4204TRMTC

Tub/Hand Shower Trim

S4208TRMTC

Shower/Hand Shower Trim

S-4200-TRM

S4200TRMTC

S-4201-TRM

S4201TRMTC

S-4202-TRM

S4202TRMTC

S4208TRM

S4208TRMTC

S-4204-TRM

S4204TRMTC

TA-10T-12A

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Go to www.symmons.com/register to register your

Symmons product.

Warranty

Summary of content (8 pages)

PAGE 1
Oxford® Oxford Trim Series Oxford Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A S-4200-TRM Shower Valve Trim S4200TRMTC Shower Valve Trim S-4201-TRM Shower Trim S4201TRMTC Shower Trim S-4202-TRM Tub/Shower Trim S4202TRMTC Tub/Shower Trim S-4204-TRM Tub/Hand Shower Trim S4204TRMTC Tub/Hand Shower Trim S4208TRM Shower/Hand Shower Trim S4208TRMTC Shower/Hand Shower Trim T-12A S-4200-TRM S4200TRMTC
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (3mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions A C B Measurements FIGURE 2 A B C D D E F G H I J K L M F E N O P Q G H L M K J I N O P Q Floor Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater. 3) All dimensions measured from nominal rough-in (see N as reference).
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system.
PAGE 4
7. Parts Breakdown FIGURE 7 Item B A L I G G H I N J H F C M K L M N H Showerhead Shower Arm Shower Handle Flange Lock Nut Dome Cover Shower Escutcheon Screws Mounting Plate Diverter/Volume Control Handle Tub Spout Hand Shower Wall Cradle 60" Hose 422SH 422SA T-549 T-543 T-542-NS-K001 T-589 422TS 422W T-547 RTS-045 Notes: 1) Append appropriate suffix for premium finish. 2) Append appropriate flow rate to showerhead or hand shower for low flow.
PAGE 5
8. Installation - Shower Valve Trim 1) Secure large mounting plate to Temptrol pressure balancing valve using mounting screws (FIGURE 8.1). FIGURE 8.1 FIGURE 8.2 FIGURE 8.3 FIGURE 8.4 2) Place diverter/volume control handle into slot in shower escutcheon (FIGURE 8.2). 3) Secure large shower escutcheon to mounting plate. Guide handle into control port on valve body. Tabs should snap in place (FIGURE 8.3). 4) Install dome cover and lock nut by turning clockwise (FIGURE 8.4).
PAGE 6
10. Installation - Slide Bar Assembly 1) Install wall cradle to stub out pipe. Tighten set screw to secure (FIGURE 10.1). FIGURE 10.1 FIGURE 10.2 2) Attach small end of hand shower hose to wall cradle. Turn clockwise to tighten (FIGURE 10.2). 3) Attach large end of hand shower hose to hand shower wand. Turn clockwise to tighten (FIGURE 10.3). FIGURE 10.
PAGE 7
11. Operation (Temperature Control) 1) Turn shower handle counter-clockwise approximately 1/4 turn to put valve in cold position (FIGURE 11.1). FIGURE 11.2 FIGURE 11.1 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 11.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 11.3). 12.
PAGE 8
14. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.