Installation Sheet

ManualsBrandsSymmons ManualsPlumbingAllura Collection S-4702-STN-REB-TRM Wall Mounted Rebuild Tub and Shower Trim Set with Lever Handle in Satin Nickel

Allura

Model Numbers

Allura Trim Series

Allura Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

S-4700-TRM

Shower Valve Trim

S-4701-TRM

Shower Trim

S-4702-TRM

Tub/Shower Trim

S-4704-TRM

Tub/Hand Shower Trim

S4708TRM

Shower/Hand Shower Trim

TRIM, TA-10, T-12A

S4700TRMTC

Shower Valve Trim

S4701TRMTC

Shower Trim

S4702TRMTC

Tub/Shower Trim

S4704TRMTC

Tub/Hand Shower Trim

S4708TRMTC

Shower/Hand Shower Trim

S-4700-TRM

S4700TRMTC

S-4701-TRM

S4701TRMTC

S-4702-TRM

S4702TRMTC

S4708TRM

S4708TRMTC

S-4704-TRM

S4704TRMTC

TA-10T-12A

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Go to www.symmons.com/register to register your

Symmons product.

Warranty

Summary of content (8 pages)

PAGE 1
Allura® Allura Trim Series Allura Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A S-4700-TRM Shower Valve Trim S4700TRMTC Shower Valve Trim S-4701-TRM Shower Trim S4701TRMTC Shower Trim S-4702-TRM Tub/Shower Trim S4702TRMTC Tub/Shower Trim S-4704-TRM Tub/Hand Shower Trim S4704TRMTC Tub/Hand Shower Trim S4708TRM Shower/Hand Shower Trim S4708TRMTC Shower/Hand Shower Trim T-12A S-4700-TRM S4700TRMTC
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (3mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions FIGURE 2 A Measurements N A B B C D E F O P C G H I J K D L F E G M N O P Q R Q H I J K L R M FLOOR Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater. 3) All dimensions measured from nominal rough-in (see I as reference).
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system.
PAGE 4
7.
PAGE 5
8. Installation - Shower Valve Trim 1) Place diverter/volume control handle into slot in shower escutcheon (FIGURE 8.1). FIGURE 8.1 FIGURE 8.2 FIGURE 8.3 FIGURE 8.4 2) Secure large shower escutcheon to Temptrol pressure balancing valve using mounting screws. Guide handle into control port on valve body (FIGURE 8.2). 3) Snap dial into large shower escutchon (FIGURE 8.3). 4) Install dome cover by turning clockwise (FIGURE 8.4). 5) Install handle to shower valve.
PAGE 6
10. Installation - Wall Cradle Assembly 1) Place mounting plate in position. Mark and drill 3/16" holes for tile anchors, 5/16" holes for drywall anchors. Install anchors (FIGURE 10.1). Note: For dry wall 1/2" thick or less, insert anchor tool into drywall anchor to secure behind wall prior to installing wall cradle. 1 FIGURE 10.1 1 2) R emove cover of hand shower cradle. Install cradle and mounting plate. Secure with three screws. Replace cover on hand shower cradle (FIGURE 10.2).
PAGE 7
11. Operation (Temperature Control) 1) Turn shower handle counter-clockwise approximately 1/4 turn to put valve in cold position (FIGURE 11.1). FIGURE 11.2 FIGURE 11.1 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 11.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 11.3). 12.
PAGE 8
14. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.