Installation Sheet

ManualsBrandsSymmons ManualsPlumbingMuseo Collection Wall Mounted Shower Trim Set with Lever Handle in Polished Chrome

Museo

Model Numbers

Museo Trim Series

Museo Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly

Installation & Operation Instructions

TRIM ONLY

S-5300-TRM

Shower Valve Trim

S-5301-TRM

Shower Trim

S-5302-TRM

Tub/Shower Trim

S-5304-TRM

Tub/Hand Shower Trim

S5308TRM

Shower/Hand Shower Trim

TRIM, TA-10, T-12A

S5300TRMTC

Shower Valve Trim

S5301TRMTC

Shower Trim

S5302TRMTC

Tub/Shower Trim

S5304TRMTC

Tub/Hand Shower Trim

S5308TRMTC

Shower/Hand Shower Trim

S-5300-TRM

S5300TRMTC

S-5301-TRM

S5301TRMTC

S-5302-TRM

S5302TRMTC

S5308TRM

S5308TRMTC

S-5304-TRM

S5304TRMTC

TA-10T-12A

Compliance

• ASME A112.18.1/CSA B125.1

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Go to www.symmons.com/register to register your

Symmons product.

Warranty

Summary of content (8 pages)

PAGE 1
Museo® Museo Trim Series Museo Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly Installation & Operation Instructions Model Numbers TRIM ONLY TRIM, TA-10, T-12A S-5300-TRM Shower Valve Trim S5300TRMTC Shower Valve Trim S-5301-TRM Shower Trim S5301TRMTC Shower Trim S-5302-TRM Tub/Shower Trim S5302TRMTC Tub/Shower Trim S-5304-TRM Tub/Hand Shower Trim S5304TRMTC Tub/Hand Shower Trim S5308TRM Shower/Hand Shower Trim S5308TRMTC Shower/Hand Shower Trim T-12A S-5300-TRM S5300TRMTC S-5
PAGE 2
1. Recommended Tools FIGURE 1 Adjustable Wrench Allen Wrench (3mm) Drill Phillips Screwdriver Safety Glasses Thread Seal Tape 2. Dimensions Measurements FIGURE 2 A A B C B D D C E F G H I J F E K L M N H O P Q G L M K I Floor J N P O Q Notes: 1) Valve body and piping not included and shown as reference only. 2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater. 3) All dimensions measured from nominal rough-in (see N as reference).
PAGE 3
. Parts Breakdown (Model Numbers Ending in TRMTC) LIMIT STOP SCREW Item 2 1 Cap Assy. T-12A 2 Flow Control Spindle TA-10 IMPORTANT: Model numbers ending in TRMTC coordinate with Temptrol pressure balancing valves ordered with Test Cap. The Test Cap is used to allow pressurization of system. Do not remove test cap from valve during wall construction, installation of valve or pressurization of system.
PAGE 4
7. Parts Breakdown FIGURE 7 N B Item A O P K I H F C L M N O P J Showerhead Shower Arm Plug Button Screw Star Washer Shower Handle Insert Dome Cover Shower Escutcheon Screws Mounting Plate Diverter/Volume Control Handle Tub Spout Hand Shower Wall Cradle 60" Hose 532SH 532SA T-665 T-666 T-668A-NS-K001 T-669 532TS 402W T-673 RTS-045 Notes: 1) Append appropriate suffix for premium finish. 2) Append appropriate flow rate to showerhead or hand shower for low flow.
PAGE 5
8. Installation - Shower Valve Trim 1) Secure large mounting plate to Temptrol pressure balancing valve using mounting screws (FIGURE 8.1). FIGURE 8.1 FIGURE 8.2 FIGURE 8.3 FIGURE 8.4 2) Place diverter/volume control handle into slot in shower escutcheon (FIGURE 8.2). 3) Secure large shower escutcheon to mounting plate. Guide handle into control port on valve body. Tabs should snap in place (FIGURE 8.3). 4) Install dome cover by turning clockwise (FIGURE 8.4). 5) Place nylon insert into handle.
PAGE 6
10. Installation - Slide Bar Assembly 1) Install wall cradle to stub out pipe. Turn clockwise to tighten (FIGURE 10.1). FIGURE 10.1 FIGURE 10.2 2) Attach small end of hand shower hose to wall cradle. Turn clockwise to tighten (FIGURE 10.2). 3) Attach large end of hand shower hose to hand shower wand. Turn clockwise to tighten (FIGURE 10.3). FIGURE 10.
PAGE 7
11. Operation (Temperature Control) 1) Turn shower handle counter-clockwise approximately 1/4 turn to put valve in cold position (FIGURE 11.1). FIGURE 11.2 FIGURE 11.1 2) Turn shower handle counter- clockwise approximately 1/2 turn to put valve in warm position (FIGURE 11.2). 3) Turn shower handle counter- clockwise approximately 3/4 turn to put valve in hot position (FIGURE 11.3). 12.
PAGE 8
14. Troubleshooting Chart Problem Cause Finish is spotting. Elements in water supply may cause water staining on finish. Solution Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Symmons Industries, Inc.