Installation Sheet

ManualsBrandsSymmons ManualsPlumbingSWM-0153-2700-1.5 5.87" Wall Mounted Two Holes Bathroom Faucet with 1.5 GPM Flow Rate and Lever Handle in Polished Chrome

Model Number

Speciﬁcation

Dimensions

Warranty

Limited Lifetime - to the original end purchaser in

consumer installations.

5 Years - for commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Wall Mounted Lavatory Faucet

Operation & Maintenance Manual

SWM-0153-2700-1.5

Note: Dimensions subject to change without notice.

Note: Append appropriate -sufx to model number.

Modiﬁcations



-0.5 0.5 gpm (1.9 L/min) ﬂow regulator



-1.0 1.0 gpm (3.8 L/min) ﬂow regulator



-2.2 2.2 gpm (8.3 L/min) ﬂow regulator



-G Grid drain

For California Residents

WARNING: This product contains chemicals known to

the State of California to cause cancer, birth defects, or

other reproductive harm.

Compliance

-ASME A112.18.1/CSA B125.1

-NSF/ANSI 61.9, NSF/ANSI 372

-WaterSense 1.5 gpm (5.7 L/min)



SWM-0153-2700-1.5 Wall Mounted Lavatory Faucet

Wall mounted lavatory faucet featuring two hole mounting

conguration. Includes ceramic cartridge and 1.5 gpm

(5.7 L/min) ow regulator. Components made from brass

and nonmetallic materials plated in standard polished

chrome nish.

Note: Requires hot and cold inlet piping to be reversed.

Measurements

Min. 1-1/2", 38 mm

Max. 1-3/4", 44 mm

B Max. 3/4", 19 mm

C Min. 5-7/8", 149 mm

(2x) Hole Size

Min. Ø 2", 51 mm

Max. Ø 2-1/4", 57 mm

E 3-3/8", 86 mm

F 9", 229 mm

G 3-3/8", 86 mm

H 4", 102 mm

I (2x) 1-7/8", 48 mm

J 3-5/16", 84 mm

FINISHED WALLFINISHED WALL

BLOCKINGBLOCKING

Certied by

NSF International

Summary of content (5 pages)

PAGE 1
SWM-0153-2700-1.5 Wall Mounted Lavatory Faucet Operation & Maintenance Manual Specification Model Number  SWM-0153-2700-1.5 Wall Mounted Lavatory Faucet -0.5 0.5 gpm (1.9 L/min) flow regulator Wall mounted lavatory faucet featuring two hole mounting configuration. Includes ceramic cartridge and 1.5 gpm (5.7 L/min) flow regulator. Components made from brass and nonmetallic materials plated in standard polished chrome finish. -1.0 1.0 gpm (3.
PAGE 2
Parts Breakdown Replacement Parts WOOD BLOCKING NOT INCLUDED D FINISHED WALL B C E A L J F G K M I H Item Description Part Number A F G Spout Assembly, 0.5 gpm Spout Assembly, 1.0 gpm Spout Assembly, 1.5 gpm Spout Assembly, 2.2 gpm RL-218-0.5 RL-218-1.0 RL-218-1.5 RL-218-2.2 F G Flow Regulator, 1.5 gpm Flow Regulator, 0.5 gpm Flow Regulator, 1.0 gpm Flow Regulator, 2.2 gpm RL-186 RL-186-0.5 RL-186-1.0 RL-186-2.
PAGE 3
Installation 1) If replacing an older faucet ensure water supply is turned OFF before removing, then turn faucet control valve ON to relieve water pressure. 2) Water lines MUST be thoroughly flushed BEFORE and AFTER installing the faucet to prevent foreign matter i.e. copper chips, sand, stones, etc. from clogging and damaging the sealing surfaces of the cartridge. 1) S ecure valve body mount (E) to wood blocking with (6x) wood screws (D).
PAGE 4
Installation 7) Remove housing (G) and flow regulator (F) from spout (A). Turn on water supplies and flush faucet free of debris. 8) Install flow regulator (F) and housing (G) to spout (A). 9) O ptional: Adjust limit stop washer to limit handle turn to the hot position if desirable. LIMIT HOT 1 3 A A F F 3 1 1 G 1 G 2 2 LIMIT COLD Operation 1) Push faucet handle inward to turn faucet on. 2) T urn counter-clockwise to put faucet handle in the hot position.
PAGE 5
Troubleshooting Chart Troubleshooting Chart Faucet no longer maintains accurate temperature. Foreign matter such as copper chips, sand, stones, etc. clogging the Remove cartridge (N) and inspect for cartridge ports and/or damaging the debris. Replace cartridge if necessary. sealing surfaces of the cartridge. Faucet leaks from handle. Same as above. Same as above. Handle is loose. Set screw has loosened. Tighten set screw (H). Finish is spotting.