Step 1 Install the Pole to the Desktop Option A: Desk Clamp Install a 1. Install the “C”-Clamp Brace(c) to the Pole (a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o), see Figure 1. c 2. Install the “C”-Clamp(b) to the pole assembly according to the thickness of the desktop. The thickness can be changed to three positions. Connect it using 2pcs M8x12 Bolts(g), and tighten using the Allen Key(o). Tighten the “C”-Clamp to the desktop using the plastic knob, see Figure 2.
Step 1 Install the Pole to the Desktop Option B: Grommet Base Install a Self Drilled Grommet Hole Installation m 1. Position the Pole(a) on the mounting surface and mark the center hole. Drill a 3/8" (10mm) diameter hole at the marked position through the mounting surface. f 2. Install the Grommet Base Plate(m) to the Pole(a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o), see Figure 5. Figure 5 3.
Step 3 Attach the VESA Plate to the Monitor q s r For Monitor with Curved or Recessed Back For Monitor with Flat Back Step 4 Slide the Monitor onto the Head of Swivel Arm h Slide the monitor onto the head of Swivel Arm(d) as shown in the above diagram. Install the security Nut(h). Make sure the security nut is installed before you rotate the monitor.
Step 5 Fix the Tilt Angle and Adjust the Level of Monitor o o Ignore this step if monitors are level Fix the tilt angle If one monitor is lower, remove the Nut(h) and turn the bolt counter clockwise with supplied Allen key(o) to raise the monitor. Install the Nut(h) after the adjustment. Tighten the bolt with the supplied Allen Key(o) to fix the tilt angle. Step 6 Make the Necessary Adjustments and Manage the Wires o n1 Manage the wires and store the Allen keys(o) in Wire Clip(n1) for future use.
English Installation Instruction UNPACKING INSTRUCTIONS ! Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage. ! Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts. ! Carefully read all instructions before attempting installation. IMPORTANT SAFETY INFORMATION ! Install and operate this device with care.
Supplied Par ts List (1) Monitor Platform-a (1) Base-b (1) Keyboard Tray-c (1)Gas Spring Arm-d (1)L Plate-e (1)Wrist Pad-f (4)M6x12 Bolt-g (4)M6x12 Bolt-h (4)M6x28 Bolt-i (2)M6x35 Bolt-j (2)Spacer-k (4)M6 Washer-l (4)M6 Nut-m (2)Square Pad-n (4)Round Pad-o (1)Allen Key-p (1)Wrench-q 2
Step 1 Connecting L Plate to Keyboard Tray p g e c ! Warning: Ensure screws are secured firmly.
Step 3 Make Decision for the Lever Location Lever located on Left or Right? Step 4 Connecting L Plate to Gas Spring Arm Lever on left “L” plate can be connected to the Gas Spring Arm in two different positions. 1. Install in a low position for fitting the keyboard tray to the surface of desktop directly. l 2. Install in a high position for leaving some space between the keyboard tray and the surface of desktop.
Step 5 Connecting Gas Spring Arm to Monitor Platform h a ! Warning: Ensure screws are secured firmly. Step 6 Attaching Lever to the Back of Monitor Platform j k ! Warning: Ensure screws are secured firmly. Note: The lever can be installed eigher on the right or the left side of monitor platform.
Step 7 Connecting Base to Gas Spring Arm p i b ! Warning: Ensure screws are secured firmly.
Step 9 Attaching Wrist Pad to Keyboard Tray f Step 10 Operating the Lever to Lift or Lower the WorkStation 7
Step 11 Adjusting the Tension of Workstation • If the weight of the monitor(s) makes it difficult to lift the workstation, adjust the screw at the back of the gas spring arm counterclockwise. • If the workstation lowers too quickly, adjust the screw at the back of gas spring arm counterclockwise. • If the workstation doesn’t easily lower down, adjust the screw at the back of gas spring arm clockwise.
