Owner's manual

SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397

PPM-8012-01 / 8012-09 / 5901-30 / 5901-44

JEEP DANA 30/44 INNER AXLE SLEEVE

Version 3.0

GENERAL NOTES:

 These instructions are also available on our website; www.synergymfg.com.

Check the website before you begin for any updated instructions and additional

photos for your reference.

 The installation of the inner axle sleeves requires removal of the wheels, brakes,

axle shafts and axle housing assembly.

 Installation of the sleeves requires drilling 1/2” holes at various places on the axle

housing.

 A competent welder is needed for completing the plug welds and circular welds

around the axle housing tube for proper installation.

 It is recommended to remove the axle housing completely; this will make drilling

and welding much easier.

 It is not necessary to remove the differential and gears or even drain the oil. Just

be careful to not let metal chips in the housing when drilling the holes for the plug

welds. Be careful to keep the housing level so gear oil does not leak out.

 The following instructions cover installation on a D30 / 44 JK housing.

Installation will be similar on a TJ housing.

1. Start by placing the front of the vehicle on jack stands placed on the front portion of

the frame or on an automotive lift.

2. Remove the front wheels.

3. Remove the brake caliper mounting bracket from knuckle using a 21mm socket and

remove the brake calipers, hang or tie the brake calipers to the frame out of the way.

4. Remove the brake rotors.

5. Remove outer axle nut using a 35mm socket.

6. Remove the ABS sensor from the unit bearing using an 8mm allen wrench.

7. Remove the 3 unit bearing bolts from the inside of the knuckle using a 13mm 12

point socket

8. Remove the unit bearings and axle shafts.

9. Remove the shocks, sway bar links, coil springs, locker actuator connectors,

driveshaft, draglink, track bar and all control arms at the housing. This will allow for

removal of the complete housing.

10. Place the axle housing on jack stands on the ground or work bench for the drilling and

welding process.

11. On the short side of the axle housing; mark the holes shown in Figure 1 and repeat the

pattern for the back/underside of the housing.

PAGE 1
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-8012-01 / 8012-09 / 5901-30 / 5901-44 JEEP DANA 30/44 INNER AXLE SLEEVE Version 3.0 GENERAL NOTES:  These instructions are also available on our website; www.synergymfg.com. Check the website before you begin for any updated instructions and additional photos for your reference.  The installation of the inner axle sleeves requires removal of the wheels, brakes, axle shafts and axle housing assembly.
PAGE 2
Figure 1 12. There should be a total of 8 holes on the short side of the housing. 13. Now mark all the holes needed for the long side of the housing, shown in Figure 2 and Figure 3.
PAGE 3
Figure 2 Figure 3
PAGE 4
14. Repeat the hole pattern for the back/underside of the housing. There should be a total of 16 hole locations. 15. Center punch all hole locations and drill with a 1/2” drill bit. 16. Remove all paint around the hole surface, around the axle center section where the axle tubes press in, and at each end of the axle tube where the inner C presses on to the housing. 17. Remove all metal shavings from both sides of the axle housing after drilling and grinding.
PAGE 5
Figure 5 21. Now begin to weld all the plug welds to the new inner axle sleeves. 22. When complete, grind down all the plug welds smooth with the axle tube. 23. Repaint your axle. 24. Reassemble and install your axle into the Jeep. Torque all suspension bolts when the vehicle is sitting on flat ground with the tires on.