Synology DiskStation DS1515 Quick Installation Guide
Table of Contents Chapter 1: Before You Start Package Contents Synology DiskStation at a Glance Safety Instructions 3 4 5 Chapter 2: Hardware Setup Tools and Parts for Drive Installation Install Drives Start Up Your DiskStation Replace System Fan 6 6 9 10 Chapter 3: Install DSM on DiskStation Install DSM with Web Assistant Learn More Appendix A: Specifications Appendix B: LED Indicator Table Synology_QIG_DS1515_20150113 2 12 12
Chapter 1 Before You Start Thank you for purchasing this Synology product! Before setting up your new DiskStation, please check the package contents to verify that you have received the items below. Also, make sure to read the safety instructions carefully to avoid harming yourself or damaging your DiskStation. Package Contents Main unit x 1 AC power cord x 1 RJ-45 LAN cable x 2 Screws for 2.
Synology DiskStation at a Glance 1 4 No. Article Name Location 1 Status Indicator Displays the status of the system. For more information, see "Appendix B: LED Indicator Table". 2 Alert Indicator Displays warnings regarding fan or temperature. For more information, see "Appendix B: LED Indicator Table". 3 Power Button 1. Press to power on the DiskStation. 2. To power off the DiskStation, press and hold until you hear a beep sound and the Power LED starts blinking.
Safety Instructions Keep away from direct sunlight and away from chemicals. Make sure the environment does not experience abrupt changes in temperature or humidity. Place the product right side up at all times. Do not place near any liquids. Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or aerosol cleaners. To prevent the unit from falling over, do not place on carts or any unstable surfaces. The power cord must plug in to the correct supply voltage.
Chapter Hardware Setup Tools and Parts for Drive Installation • A screwdriver (only for 2.5" drives) • At least one 3.5” or 2.5” SATA drive (please visit www.synology.com for compatible drive models.) Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please back up any important data before installation. Install Drives 1 Press the lower part of the hard drive tray to pop out the handle.
3 Load drives in the drive trays. • For 3.5” drives: Remove the fastening panels from the sides of the drive tray. Place the drive in the drive tray. Then insert the fastening panels to secure the drive in place. • For 2.5” drives: Remove the fastening panels from the sides of the drive tray and store them in a safe place. Place the drive in the blue area (shown below) of the drive tray. Turn the tray upside down and tighten the screws to secure the drive in place.
4 Insert the loaded hard drive tray into the empty hard drive bay. Note: Make sure the tray is pushed in all the way. Otherwise, the drive might not be able to function properly. 5 Press the handle in flush with the front panel to hold the hard drive tray in place. 6 Insert the hard drive tray key into the hard drive tray lock, turn the key clockwise (to the "I" position) to lock the handle of the hard drive tray, and then remove the key.
Start Up Your DiskStation 1 Use the LAN cable to connect the DiskStation to your switch, router or hub. 2 Connect the AC adapter to the power port of the DiskStation. Connect one end of the AC power cord to the AC power adapter, and the other to the power outlet. 3 Press the power button. Congratulations! Your DiskStation is now online and detectable from a network computer.
Replace System Fan Your DiskStation will play beep sounds if either of the system fans is not working. Follow the steps below to replace the malfunctioning fan with a good one. To replace the system fan: 1 Shut down your DiskStation. Disconnect all cables connected to your DiskStation to prevent any possible damages. 2 Fans are numbered as follows: 3 Remove the 2 screws that secure the fan panel.
4 Remove the malfunctioning fan: a Pull the fan panel from your DiskStation. b Disconnect the fan cable from the connectors located near the bottom of the fan socket, and then remove the fan panel. 5 Install the new fan: a Connect the fan cable of the new fan to the fan connector. b With the fan cable within the fan pointing at the bottom-right corner, place the fan into the fan socket. 6 Replace and tighten the two screws you removed in step 3.
Chapter Install DSM on DiskStation After hardware setup is finished, please install DiskStation Manager (DSM) – Synology’s browser-based operating system – on your DiskStation. Install DSM with Web Assistant Your DiskStation comes with a built-in tool called Web Assistant that helps you download the latest version of DSM from the Internet and install it on your DiskStation. To use Web Assistant, please follow the steps below. 1 Power on the DiskStation.
Appendix A Specifications Item DS1515 Compatible Drive Type 3.5"/2.5" SATA3/SATA2 x 5 Maximum Internal Raw Capacity 40TB (5 x 8 TB hard drives) External Ports • USB 3.0 x 2 • eSATA x 2 LAN Ports 1GbE (RJ-45) x 4 Size (H x W x D) (mm) 157 x 248 x 233 Weight (kg) 4.15 • Windows XP onward Supported Clients • Mac OS X 10.5 onward • Ubuntu 9.
Appendix B LED Indicator Table LED Indicator Color Status Description Green Static Volume normal Volume degraded or crashed STATUS Orange Blinking Volume not created DSM not installed Off ALERT Power Orange HDD hibernation Blinking Off Blue System normal Static Powered on Blinking Booting up or shutting down Off Front LAN Green Powered off Static Network connected Blinking Network active Off Rear LAN (on upper side of jack) No network Green Static Gigabit connection Orange
SYNOLOGY, INC. END USER LICENSE AGREEMENT IMPORTANT–READ CAREFULLY: THIS END USER LICENSE AGREEMENT ("EULA") IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR A LEGAL ENTITY) AND SYNOLOGY, INC. ("SYNOLOGY") FOR THE SYNOLOGY SOFTWARE INSTALLED ONTO THE SYNOLOGY PRODUCT PUCHASED BY YOU (THE “PRODUCT”), OR LEGALLY DOWNLOADED FROM WWW.SYNOLOGY.COM, OR ANY OTHER CHANNEL PROVIDED BY SYNOLOGY ( "SOFTWARE").
Section 14. Export Restrictions. You acknowledge that the Software is subject to U.S. export restrictions. You agree to comply with all applicable laws and regulations that apply to the Software, including without limitation the U.S. Export Administration Regulations. Section 18. Dispute Resolution.
SYNOLOGY, INC. LIMITED PRODUCT WARRANTY THIS LIMITED WARRANTY ("WARRANTY") APPLIES TO THE PRODUCTS (AS DEFINED BELOW) OF SYNOLOGY, INC. AND ITS AFFILIATES, INCLUDING SYNOLOGY AMERICA CORP, (COLLECTIVELY, "SYNOLOGY"). YOU ACCEPT AND AGREE TO BE BOUND BY THE TERMS OF THIS WARRANTY BY OPENING THE PACKAGE CONTAINING AND/OR USING THE PRODUCT. IF YOU DO NOT AGREE TO THE TERMS OF THIS WARRANTY, DO NOT USE THE PRODUCT.
Products may be available from Synology upon written request. 2.6 Exclusions.
between Customer and Synology. The arbitration, or any portion of it, will not be consolidated with any other arbitration and will not be conducted on a class-wide or class action basis. The arbitration shall be held in King County, Washington, U.S.A. by submission of documents, by telephone, online or in person as determined by the arbitrator at the request of the parties.
