Synology Adapter Card E10M20-T1 Hardware Installation Guide
Table of Contents Chapter 1: Before You Start Package Contents Hardware Specification LED Indicator Table Safety Instructions 3 4 5 6 Chapter 2: Hardware Setup Tools and Parts for Installation Attach M.
1 Chapter Before You Start Thank you for purchasing this Synology product! Before setting up your new adapter card, please check the package contents to verify that you have received the items below. Also, make sure to read the safety instructions carefully to avoid harming yourself or damaging your adapter card. Note: All images below are for illustrative purposes only, and may differ from the actual product.
Hardware Specification Item E10M20-T1 Host Bus Interface PCIe 3.0 x 8 Bracket Height (mm) 80 (low profile), 120 (full height) Size (H x W x D) (mm) 71.75 x 200.55 x 17.70 General Agency Certification Environment Requirement • FCC Class B • CE Class B • BSMI Class B • VCCI • RCM • RoHS Compliant • Operating Temperature: 0°C to 40°C (32°F to 104°F) • Storage Temperature: -20°C to 60°C (-5°F to 140°F) • Relative Humidity: 5% to 95% RH Storage Interface NVMe Supported Form Factor M.
LED Indicator Table LED Indicator LAN (on upper side of jack) Color Status Description Green Static 10 Gbps connection Orange Static 5 Gbps/2.5 Gbps/1 Gbps/100 Mbps connection Off LAN (on lower side of jack) Green Off No network Static Network connected Blinking Network active No network Note: Model specifications are subject to change without notice. Please refer to www.synology.com for the latest information.
Safety Instructions Keep away from direct sunlight and from chemicals. Make sure the environment does not experience abrupt changes in temperature or humidity. Place the product right side up at all times. Do not place near any liquids. Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or aerosol cleaners. To prevent the unit from falling over, do not place on carts or any unstable surfaces. The power cord must plug in to the correct supply voltage.
2 Chapter Hardware Setup Tools and Parts for Installation • A PH1 screwdriver (for adding M.2 SSD to E10M20-T1 adapter card) • A PH2 screwdriver (for replacing the bracket) Attach M.2 SSD to E10M20-T1 Adapter Card Please refer to www.synology.com/compatibility to make sure your Synology NAS supports E10M20-T1 adapter card before attaching it. For the instructions on how to install the E10M20-T1 to your Synology NAS, please refer to the Hardware Installation Guide of your NAS. To attach M.
b Insert SNV3400-400G into the slot. Make sure the card is fully inserted. c Tighten SNV3400-400G with a screw. d Repeat previous three steps if installing another M.2 SSD is needed. Slots are numbered as shown below. 1 2 e Remove the protective film from the thermal pad and attach the thermal pad to the heatsink.
f Tighten the heatsink with four screws. Please make sure the heatsink is firmly attached to the adapter card to ensure the smooth running of the M.2 SSD. • For M.2 22110 SSD (SNV3500-400G): a Insert SNV3500-400G into the slot. Make sure the card is fully inserted. b Tighten SNV3500-400G with a screw.
c Remove the protective film from the thermal pad and attach the thermal pad to the controller of SNV3500400G. Attach the rubber next to the screw pillar. d Repeat previous three steps if installing another M.2 SSD is needed. Slots are numbered as shown below. 1 2 e Tighten the heatsink with four screws. Please make sure the heatsink is firmly attached to the adapter card to ensure the smooth running of the M.2 SSD.
3 Replace the low-profile bracket with a full-height bracket if needed. a Remove the screws that secure the low-profile bracket. b Tighten the full-height bracket with two screws.
SYNOLOGY, INC. END USER LICENSE AGREEMENT IMPORTANT–READ CAREFULLY: THIS END USER LICENSE AGREEMENT ("EULA") IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR A LEGAL ENTITY) AND SYNOLOGY, INC. ("SYNOLOGY") FOR THE SYNOLOGY SOFTWARE INSTALLED ONTO THE SYNOLOGY PRODUCT PURCHASED BY YOU (THE "PRODUCT"), OR LEGALLY DOWNLOADED FROM WWW.SYNOLOGY.COM, OR ANY OTHER CHANNEL PROVIDED BY SYNOLOGY ( "SOFTWARE").
request. Section 11. Disclaimer of Warranties. EXCEPT AS EXPRESSLY SET FORTH ABOVE, THE SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS. SYNOLOGY AND ITS SUPPLIERS HEREBY DISCLAIM ALL OTHER WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, ARISING BY LAW OR OTHERWISE, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR USE, TITLE AND NONINFRINGEMENT, WITH REGARD TO THE SOFTWARE.
SYNOLOGY, INC.LIMITED PRODUCT WARRANTY THIS LIMITED WARRANTY ("WARRANTY") APPLIES TO THE PRODUCTS (AS DEFINED BELOW) OF SYNOLOGY, INC. AND ITS AFFILIATES, INCLUDING SYNOLOGY AMERICA CORP, (COLLECTIVELY, "SYNOLOGY"). YOU ACCEPT AND AGREE TO BE BOUND BY THE TERMS OF THIS WARRANTY BY OPENING THE PACKAGE CONTAINING AND/OR USING THE PRODUCT.
3.3 Warranty Support and Exclusive Remedy. If Customer gives notice of noncompliance with any of the warranties set forth in Section 3.
the Synology end user license agreement accompanying any Software furnished by Synology or an authorized Synology distributor or reseller; and (b) not attempt to reverse engineer any Product or component thereof or accompanying Software or otherwise misappropriate, circumvent or violate any of Synology's intellectual property rights. 5.2 Assignment. Customer will not assign any of its rights under this Warranty directly, by operation of law or otherwise, without the prior written consent of Synology. 5.
FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
この装置は、クラス B 機器です。この装置は、住宅環境で使用することを 目的 としていますが、この装置がラジオやテレビジョン受信機に近接して使 用され ると、受信障害を引き起こすことがあります。 取扱説明書に従って正しい取り扱いをして下さい。 VCCI 一 B
