Synology RackStation RS1619xs+ Hardware Installation Guide
Table of Contents Chapter 1: Before You Start Package Contents Synology RackStation at a Glance System Fans Safety Instructions 3 4 5 6 Chapter 2: Hardware Setup Tools and Parts for Drive Installation Install Drives Add RAM Modules to RackStation Attach SSDs to RackStation Attach A Network Interface Card to RackStation Replace Redundant Power Supplies on RackStation Start Up RackStation 7 7 9 11 12 13 13 Chapter 3: Install DSM on RackStation Install DSM with Web Assistant Learn More Appedix A: Specific
1 Chapter Before You Start Thank you for purchasing this Synology product! Before setting up your new RackStation, please check the package contents to verify that you have received the items below. Also, make sure to read the safety instructions carefully to avoid harming yourself or damaging your RackStation. Note: All images below are for illustrative purposes only, and may differ from the actual product. Package Contents Main unit x 1 3 AC power cord x 2 Screws for 3.5” drives x 20 Screws for 2.
Synology RackStation at a Glance 12 3 56 4 7 8 16 9 11 10 16 9 9 12 13 14 15 No. Article Name 1 Power Indicator Displays power status of the RackStation. For more information, see "Appendix B: LED Indicator Table". 2 Power Button 1. Press to power on the RackStation. 2. To power off the RackStation, press and hold until you hear a beep sound and the Power LED starts blinking. 3 Alert Indicator Displays warnings regarding fan or temperature.
System Fans If any fan failure occurs, please refer to the images below to locate the failed fan(s) indicated in DSM. The fans are numbered as below: 1 2 To replace the failed fan(s), please contact Synology Technical Support at www.synology.com/support for technical assistance.
Safety Instructions Keep away from direct sunlight and away from chemicals. Make sure the environment does not experience abrupt changes in temperature or humidity. Place the product right side up at all times. Do not place near any liquids. Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or aerosol cleaners. To prevent the unit from falling over, do not place on carts or any unstable surfaces. The power cord must plug in to the correct supply voltage.
2 Chapter Hardware Setup Tools and Parts for Drive Installation • A screwdriver. • At least one 3.5” or 2.5” SATA drive (please visit www.synology.com for compatible drive models.) Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please back up important data before installation. Install Rack mounts Fix the two rack mount kits on both sides with the screws provided. Install Drives 1 Pull the drive tray handle outwards to remove the tray.
• For 2.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten the screws into the four spots indicated below to secure the drive. 3 Insert the loaded drive tray into the empt y drive bay. RS1619xs+ Important: Make sure the drive tray is pushed all the way in or the drive may not function properly. 4 Push the handle inward to secure the drive tray.
Add RAM Modules to RackStation The optional Synology RAM module is designed for RackStation memory expansion. Follow the steps below to install, check, or remove a RAM module on your RackStation. To install a RAM module: 1 Shut down your RackStation and disconnect all cables to prevent any possible damage. 2 Remove the top cover: a Loosen the four screws of the top cover of your RackStation with a screwdriver. Respective screw position is indicated above.
3 Insert the new memory module: a Push the retaining clips on the slot outwards. b Align the gold edge of the module with the memory slot. c Firmly push the memory module down. The retaining clips will snap into position if the module is correctly inserted. Important: Hold the memory module by its edges. Do not touch the golden connectors. To make sure RackStation recognizes the new memory capacity: 1 Install DiskStation Manager (DSM). (See Install DSM with Web Assistantt for more information.
Attach SSDs to RackStation Your RackStation supports optional M.2 2280 NVMe / SATA SSDs. Follow the steps below to add them to your RackStation. 1 Follow step 1 and 2 of Add RAM Modules to RackStation to shut down your RackStation. Disconnect all cables and remove the top cover. 2 Insert a M.2 SATA SSD into SLOT1 (as shown below). Insert a second SSD in SLOT 2 if needed. 3 Tighten the SSD(s) with a screw.
Attach A Network Interface Card to RackStation Your RackStation supports one PCIe x8 add-on network interface card.1 To install a network interface card: 1 Follow step 1 and 2 of Add RAM Modules to RackStation to shut down your RackStation. Disconnect all cables and remove the top cover. 2 Insert your network interface card. a Lift the black latch from the expansion slot cover. Remove the cover from the expansion slot.
Replace Redundant Power Supplies on RackStation 1 Turn to the back of your RackStation and push the lever of the redundant power supply. 2 Pull the redundant power supply out. 2 1 3 Prepare a new power supply and push it into the slot until you hear a click. Start Up RackStation 1 Turn to the back of your RackStation. Connect one end of each power cord to the power ports and the other end to a power outlet.
3 Chapter Install DSM on RackStation After hardware setup is finished, please install DiskStation Manager (DSM) – Synology’s browser-based operating system – on your RackStation. Install DSM with Web Assistant Your RackStation comes with a built-in tool called Web Assistant that helps you download the latest version of DSM from the Internet and install it on your RackStation. To use Web Assistant, please follow the steps below. 1 Power on your RackStation.
A Appendix Specifications Item Compatible Drive Type Maximum Internal Raw Capacity External Device Port RS1619xs+ • 3.5"/2.5" SATA x 4 • M.2 2280 NVMe/SATA SSD x 2 • 48 TB (4 x 12 TB HDD) • 192 TB with RX1217 / RX1217RP (expansion unit) x 1 • USB 3.0 x 2 • Expansion port x 1 LAN Port Gigabit x 4 PCIe Slot PCIe Gen3 x8 slot for add-on card (optional) Size (H x W x D) (mm) 44 x 430.5 x 483.6 (Not including rack mount kits) / 44 x 480 x 518.6 (Including rack mount kits) Weight (kg) 8.
B Appendix LED Indicator Table LED Indicator Power Color Green Status Description Static Powered on Blinking Booting up / Shutting down Off Green Powered off Static Volume normal Volume degraded / Volume crashed STATUS Orange Blinking Volume not created DSM not installed Off ALERT Redundant Power Orange Blinking Off Green Off Orange Static Drive ready and idle Blinking Accessing drive Static Drive error1 No internal drive Green Static 1 Gbps connected Orange Static 100 Mbps
SYNOLOGY, INC. END USER LICENSE AGREEMENT IMPORTANT–READ CAREFULLY: THIS END USER LICENSE AGREEMENT ("EULA") IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR A LEGAL ENTITY) AND SYNOLOGY, INC. ("SYNOLOGY") FOR THE SYNOLOGY SOFTWARE INSTALLED ONTO THE SYNOLOGY PRODUCT PUCHASED BY YOU (THE "PRODUCT"), OR LEGALLY DOWNLOADED FROM WWW.SYNOLOGY.COM, OR ANY OTHER CHANNEL PROVIDED BY SYNOLOGY ( "SOFTWARE").
request. Section 11. Disclaimer of Warranties. EXCEPT AS EXPRESSLY SET FORTH ABOVE, THE SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS. SYNOLOGY AND ITS SUPPLIERS HEREBY DISCLAIM ALL OTHER WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, ARISING BY LAW OR OTHERWISE, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR USE, TITLE AND NONINFRINGEMENT, WITH REGARD TO THE SOFTWARE.
SYNOLOGY, INC. LIMITED PRODUCT WARRANTY THIS LIMITED WARRANTY ("WARRANTY") APPLIES TO THE PRODUCTS (AS DEFINED BELOW) OF SYNOLOGY, INC. AND ITS AFFILIATES, INCLUDING SYNOLOGY AMERICA CORP, (COLLECTIVELY, "SYNOLOGY"). YOU ACCEPT AND AGREE TO BE BOUND BY THE TERMS OF THIS WARRANTY BY OPENING THE PACKAGE CONTAINING AND/OR USING THE PRODUCT. IF YOU DO NOT AGREE TO THE TERMS OF THIS WARRANTY, DO NOT USE THE PRODUCT.
("RMA") number by Synology before shipment and must be returned in accordance with Synology's then current RMA procedures. Customer may contact any authorized Synology distributor or reseller or Synology Support to obtain assistance in obtaining an RMA, and must provide proof of purchase and product serial number when asking for such assistance. For warranty claims, Customer must return the complete Product to Synology in accordance with this Section 3.3 to be eligible for coverage under this Warranty.
USE OR INABILITY TO USE THE PRODUCT, ANY ACCOMPANYING DOCUMENTATION OR SOFTWARE AND ANY OTHER GOODS OR SERVICES PROVIDED UNDER THIS WARRANTY IS LIMITED TO THE AMOUNT ACTUALLY PAID BY CUSTOMER FOR THE PRODUCT REGARDLESS OF THE AMOUNT OF DAMAGES CUSTOMER MAY INCUR AND WHETHER BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHER THEORY. The foregoing disclaimer of certain damages and limitation of liability will apply to the maximum extent permitted by applicable law.
5.8 Severability. If any provision of this Warranty is held by a court of competent jurisdiction to be invalid, illegal, or unenforceable, the remainder of this Warranty will remain in full force and effect. 5.9 Entire Agreement. This Warranty constitutes the entire agreement, and supersedes any and all prior agreements, between Synology and Customer related to the subject matter hereof.
この装置は、クラス A 機器です。この装置を住宅環境で使用すると電波妨 害を引き起こすことがあります。この場合には使用者が適切な対策を講ずる よう要求されることがあります。 VCCI 一 A
