I0, I1, I12, I2 User manual
Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 01.02.
Table of contents Table of contents 1 General information about this manual 4 2 For your safety 6 3 Features 8 4 Installation 9 5 Technical specifications 11 6 Protecting the environment 19 User manual I0, I1, I12, I2 (Issue 1) 3 / 20
General information about this manual 1 General information about this manual This user manual contains important instructions for the safe operation of the unit. Read and follow the safety instructions and all other instructions. Keep the manual for future reference. Make sure that it is available to all those using the device. If you sell the unit, please make sure that the buyer also receives this manual. Our products are subject to a process of continuous development. Thus, they are subject to change.
General information about this manual Symbols used General warning of a dangerous location Warning of suspended load Notice User manual I0, I1, I12, I2 (Issue 1) 5 / 20
For your safety 2 For your safety Intended use This device is designed as a PA system. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use. This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience.
For your safety NOTICE Operating conditions This device has been designed for indoor use only. à To prevent damage, never expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and strong vibrations.
Features 3 Features Special features of this passive 2-way full-range speaker: – Connectivity options: Screw connections; compatible plugs for connection to the speaker cable enclosed – Especially suitable for use with DSP amplifiers of Syrincs – Trapezoidal housing, multiplex grey/black – Meant for wall mounting Optionally available accessories: – Universal wall mount, swivel and tilt type (Syrincs I-series wall mount black) – Wall mount with multiple holes, compatible with Syrincs I0, horizontal swivel
Installation 4 Installation Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively. Create all connections while the device is off. Use the shortest possible high-quality cables for all connections.
Installation We recommend you to set up the speakers in a way, that their sound signals can reach the audience unobstructedly. It will often be helpful to mount the speakers on tripods. Thus, the sound will be evenly spread with maximum range throughout the audience area. Always use high grade cables to connect your equipment. Otherwise you won't reach maximum sound quality. For optimum results both impedance and power rating of the speaker must match the requirements of the amplifier / input signal.
Technical specifications 5 Technical specifications Syrincs I0 Configuration 1 × 5" woofer 1 × 28 mm dome tweeter Power handling 50 W (RMS) 120 W (AES) Sensitivity (1 W/1 m) 87 dB Impedance 16 Ω Maximum sound pressure level 104 dB (1 m) 110 dB (peak) Frequency response 70 Hz … 20 kHz (–3 dB) Dimensions (W × H × D) 173 mm × 335 mm × 165 mm Weight 4.
Technical specifications Syrincs I1 Configuration 1 × 6" woofer 1 × 28 mm dome tweeter Power handling 50 W (RMS) Sensitivity (1 W/1 m) 89 dB Impedance 16 Ω Maximum sound pressure level 106 dB (1 m) 112 dB (peak) Frequency response 75 Hz … 20 kHz (–3 dB) Dimensions (W × H × D) 173 mm × 335 mm × 165 mm Weight 4.
Technical specifications Syrincs I12 Configuration 2 × 6" woofer 1 × dome tweeter array (6 × 25 mm) Power handling 160 W (RMS) Sensitivity (1 W/1 m) 92 dB Impedance 8Ω Maximum sound pressure level 112 dB (1 m) 118 dB (peak) Frequency response 75 Hz … 20 kHz (–3 dB) Dimensions (W × H × D) 205 mm × 645 mm × 184 mm Weight 9.
Technical specifications Syrincs I2 Configuration 1 × 8" woofer 1 × dome tweeter array (4 × 25 mm) Power handling 80 W (RMS) Sensitivity (1 W/1 m) 88 dB Impedance 16 Ω Maximum sound pressure level 107.5 dB (1 m) 113.5 dB (peak) Frequency response 55 Hz … 20 kHz (–3 dB) Dimensions (W × H × D) 241 mm × 418 mm × 211 mm Weight 6.
Technical specifications Frequency response, Syrincs I0 User manual I0, I1, I12, I2 (Issue 1) 15 / 20
Technical specifications Frequency response, Syrincs I1 16 / 20 User manual I0, I1, I12, I2 (Issue 1)
Technical specifications Frequency response, Syrincs I12 User manual I0, I1, I12, I2 (Issue 1) 17 / 20
Technical specifications Frequency response, Syrincs I2 18 / 20 User manual I0, I1, I12, I2 (Issue 1)
Protecting the environment 6 Protecting the environment Packaging For the packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
