One Setup Guide Model: G11
Welcome to the Syrp family Before you start filming, there are a few simple steps to follow to ensure your Genie One is assembled correctly and you’re shooting smoothly. This guide will walk you through the correct Genie One set up, as well as some helpful tips. Additional resources can be found at support.syrp.
What’s in the Box Genie One Rope Hooks USB-C to USB-A Charging Cable Lens Cloth Genie Linear Accesory Incl.
Genie One Wireless connection light Charging light Camera recording light Power Button Camera Port USB-C Port 3/8" Camera Screw Quick Release Lock Panning/Linear Base Bubble level
Mounting for Panning Movement ! IMPORTANT Ensure the Quick Release button is in the lock position and there is no orange showing. 1 Twist the Panning Accesory camera screw knob onto the Tripod 3/8” camera screw. 2 Align the Genie One with the Panning Accessory and firmly press it into the base until you hear a click.
Mounting for Linear Movement ! IMPORTANT Ensure the Quick Release button is in the lock position and there is no orange showing. 1 Twist the Linear Accessory camera screw knob onto the Slider carriage 3/8” camera screw 2 Align the Genie One with the Linear Accessory and firmly press it into the base until you hear a click.
Tie off the Genie Rope Tie 7 off the Genie rope to both ends of your track using the supplied rope hooks. Make note of the correct direction of the rope as illustrated. Rope should tie off on the rope hooks on the same side as it exits the linear plate, creating the smallest angle.
Mount Camera Screw 7 your camera and ballhead to the Genie One 3/8” camera screw ! IMPORTANT Do not lift the Genie and or attached equipment by the camera. Always detach first and transport separately.
Camera Control 1 Plug the 2.5mm jack-end of a Syrp Shutter Link Cable into the Genie One Camera Port. 2 Connect the opposite end of the Shutter Link Cable into the remote port of your camera.
Connect to the Genie One 1 Turn on the Genie One, press the on button once. 2 Turn Bluetooth on in your mobile device settings. 3 Download the Syrp Genie App 4 Open the Syrp Genie App. Continued overleaf.
App Connect 1 Tap the CONNECT icon. 2 Select your Genie or multiple One GENIE ONE Tracking One GENIE ONE Tracking Genies to link to more than one Genie. 3 Tick confirms Connection.
Charging 1 Plug the USB cable into a wall charger, laptop or USB port. ! IMPORTANT Only use a power supply rated as USB-C 5V/1-3A 2.5hrs* 2 Plug the USB-C plug into the Genie One charging port. * Charge time is 2.5hrs with a 5V/3A power supply.
Threading the Linear Plate 1 Thread an untied end of the rope into the bottom of the roller where it’s marked ‘IN’ following the arrow. Thread the rope end through to the bottom of the next roller marked ‘OUT’. Ensure the rope is sitting at the bottom of the roller. 2 Continue to thread the rope through the next 2 rollers marked T5. 3 Repeat the above steps 3 more times, stacking each wind above the last. Ensure each rope sits individually in the grooves of the Guide Rollers Continued overleaf.
Checking the Linear Plate 4 Turn the linear plate so you are looking face on to the Guide Rollers.
Genie Quick Tips When recording photographs always, set your camera and lens to manual focus (MF). If set to Auto Focus (AF) the camera can misfire leading to missed frames. Turn image review OFF on your camera. On some cameras, image review can cause missed frames in your time-lapse.
Firmware Tips If you’re having difficulty updating the Firmware, try these tips. • Try to update on a different device. If it works you can go back to using your original device. • Do not connect to other Bluetooth devices while updating. It's best to turn off other nearby Bluetooth devices completely, or the update may fail. • Try the update from a different location; in some situations unknown interference can cause a failed update. For more information visit support.syrp.
Stay in Touch 7 We hope that the Genie One helps to expand your creativity and assists in making better films. Please stay in touch with us, join our community and show us your work. www.syrp.co http://youtube.com/syrpey vimeo.com/syrp instagram.com/syrp_ https://www.facebook.com/syrp.co twitter.com/syrp_ syrp@syrp.co.nz 32 Crummer Rd Auckland 1021 New Zealand Ph.