Bluetooth Low Energy Tire Pressure Monitoring System User Manual Model: BSI-03 1
Table of Contents 1. PRODUCT INTRODUCTION..................................................................................................... 3 2. NOTICE.......................................................................................................................................... 3 3. BLE TPMS SPECIFICATION..................................................................................................... 5 4. BLE TPMS PACKAGE.....................................................................
1. Product Introduction With the new technology product: Bluetooth Low Energy Tire Pressure Monitoring System Retrofit Kit (hereinafter referred to as BLE TPMS), the driver could get the accurate tire pressure and temperature at any time through smart phone by using this kit while driving. When the system detects abnormal status, it will alarm the driver actively, and show the abnormal data and its tire location on the BLE TPMS APP (hereinafter referred to as APP). 2. Notice Product Warning 2.1.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
3. BLE TPMS Specification BLE Sensor Specification Operating Voltage Operating Humidity Operating Current Storage Temperature Operating Temperature Monitored Pressure Range Monitored Temperature Range Operating Frequency Transmission Power Battery Life Battery Capacity Weight Voice Dongle Specification Operating Voltage Operating Humidity Operating Current Storage Temperature Operating Temperature Sound Pressure (min.
4. BLE TPMS Package Part Name Quantity BLE TPMS Sensor 4 pcs Valve 4 pcs Screw 4 pcs User Manual 1 pcs Voice Dongle 1 pcs 5. BLE TPMS Sensor Installation 5.1 BLE TPMS Sensor Accessories 1. Screw 2.TPMS sensor 3.Valve and rubber washer 4.Washer 5.Nut 6.
5.2 Installation Steps (Fig. 1) Loosen the tire: fix both sides of the tire, press and make it bulge. (Fig. 2) Remove the tire: the valve faces the mounting arm in the one o’clock direction when removing the tire. (Fig. 3) Install the sensor and valve: insert the valve through the rim hole, fix the screw to secure the valve and sensor by 2 Nm in torque, attach the sensor body to the inner surface of the rim by adjusting the angle of the sensor body. (Fig.
Note 1: After installation, recalibrate the rim set on the balance machine to avoid shaking during driving. Note 2: The “sensor valve” and “screw” are not included in product warranty. When replacing the sensor, it is suggested to use a new sensor valve and screw. 6. APP Download and Installation 6.1 Operation System Required TPMS system supports both smartphone for Android & iOS operation system. (Bluetooth 4.0)。 APP Download APPLE APP Store Operation System iOS 7.1.
In case “Location Services” is not turned on properly, please turn it on in “Settings” (only for iOS system).
7. Setting & Add Device 7.1 Introduction of Contents Please make sure the “Bluetooth” & “Location Service” Setting functions are enabled when you start to use the APP.
iOS version Android version Main Menu: Driving: Displays the pressure, temperature and voice warning of the four tires. (Note 1) Setting: System settings. Add Device Setting: Enter the learning setting when using for the first time. (p.11). Exchange: Tire exchange setting. Voice Dongle: Dongle setting. (Note 2) About: Disclaimer & Company Information. Note 1: iOS version: enter the system Settings-> BLE TPMS APP->Notifications-> Enable notification and support background execution.
7.2 New Device Setting iOS version Android version New Device Setting Manual Learning: 1. Select Manual Learning.
iOS version Android version 2. Choose tire 1 and key in the five-character sensor ID (Please refer to last page: ID sticker), which might include “0-9”, “A-F”, or ”af”, when a blank space pops up. (Pic 3) Pic 3 Pic 3 3. Manual Learning completed. (Pic 4) Using the same method, set up the ID learning for tire 2(RF), tire 3(RR) and tire 4(LR) in sequence.
7.3 Rapid Deflation Setting iOS version Android version Rapid Deflation Setting : 1. Select Rapid Deflation Setting. (Pic 1) Pic 1 Pic 1 2. Choose tire 1 (LF) and deflate the tire pressure. The APP will look for the deflation signal, showing new ID number on the dialogue display. You can press “OK’ to finish this step or press "Cancel". It takes 120 seconds to perform this step.
iOS version Android version 3. Rapid Deflation completed. (Pic 3) Using the same method, set up the ID learning for tire 2(RF), tire 3(RR) and tire 4(LR) in sequence.
7.4 QR Code Setting iOS version Android version QR Code Setting : 1. Select QR Code Setting. (Pic 1) Pic 1 Pic 1 2. Choose tire 1 (LF) The APP will scan qr code, showing new ID number on the dialogue display. You can press “Clear ID” or “Stop scan” or “Save ”button.
iOS version Android version 3. QR Code completed. (Pic 3) Using the same method, set up the ID learning for tire 2(RF), tire 3(RR) and tire 4(LR) in sequence.
8. Alarms and Warnings iOS version Android version System Warning: When abnormal tire system status occurs, the value of the corresponding tire turns red, and it alarms with a sound and warning symbol. The warning symbols on each tire display, from the left to the right, are: tire pressure warning, rapid deflation, no signal, tire temperature warning and low battery power of sensor. If you do not want to hear the sound from the voice dongle and the APP, please exit the APP and mute the voice dongle. 1.
9. System Setting iOS version Android version System Setting: Unlock the system setting by clicking on the “lock” icon on the upper-right side of the main display. Change settings on “front wheel” and “rear wheel” then press the “Save” button to save the settings. You can press “Default Value” to reset all settings. (Note 1) Pressure Unit: Bar, kPa, psi; 3 different pressure units. Temperature Unit: ℃, ℉; 2 different temperature units.
10. Exchange Setting iOS version Android version Tire Exchange Setting: 1.Unlock the system setting by clicking on the “lock” icon on upperright side of the main display. Pic 1 Pic 1 2.Tire positions are displayed in sequence (1, 2, 3, and 4), meaning left-front, right-front, right-rear and left-rear with ID.
iOS version Android version Drag the dialogue display of the tire to the desired location for all desired exchanged tires, then press the “Save” icon. It will display the new tire positions in sequence (1, 2, 3, and 4). Pic 3 Pic 3 iOS version: Click the “lock” icon once again to complete the settings. Android version: Click “exit” and then click on the “lock” icon again to complete the settings.
11. Voice Dongle Setting iOS version Android version Voice Dongle Setting: Recommend for 5V/2A car USB power charger adapter for voice dongle. Pic 1 Pic 1 1. Press the red voice dongle button for 1.5 seconds. When you hear “beep,” you will go into the Bluetooth pairing mode (LED : flicker of Red and Blue light ).
iOS version Android version 2.Enter menu ->click ”Dongle” function ->click “TPMS_Dongle_sn” (random serial number), “TPMS_Dongle_sn Connected” will be shown in blue color. (Pic 3) Pic 3 Pic 4 Pic 3 3. iOS version: The APP will automatically download the settings when you hear “Setup completed.” You can start using after “Voice dongle Setting OK” is displayed. Android version: Please click write. The APP will automatically download the settings when you hear “Setup completed.
12. About iOS version Android version About: “Product Information” is displayed. It describes the definition of “Warning Symbol” and shows the link to the “Company Website”. You can press the link to go to the company’s website.
13. Frequently Asked Questions 1. After inserting the sensor ID number into the APP, the dialogue display remains without a value. A: TPMS sensor only transmits data when the sensor is on a car that is going over 20 km per hour, is started after parked for over ten minutes, or the tire pressure difference at the moment is 30 kPa. During other times, data will not be transmitted in order to save power. You can check if the TPMS sensor is working normally through tire pressure increase or deflation. 2.
Disclaimer: This product is only to be used as precautionary warning and provides to user as a convenient secondary safety equipment. Please follow the standard installation procedures or ask a qualified tire shop to install the product. If the tire has been damaged or traffic accident resulting from improper driving behavior occurs, the company will not be responsible for any civil or criminal liabilities. Other relevant latest information of SYSGRATION TPMS is available at our website (http://www.
BLE TPMS MODEL: SBT-30 WARRANTY CERTIFICATE SERIAL NUMBERS LF LR RF RR Sensor’s ID stickers: LF ID stickers here RF ID stickers here LR ID stickers here RR ID stickers here WARRANTY PERIOD: One (1) Year PURCHASE DATE: Y. M. D. DISTRIBUTOR STAMP: http://www.sysgration.