TPMS Receiver User Manual Model: TA86 1
1. Product Introduction With the new technology product: Bluetooth Low Energy Tire Pressure Monitoring System Retrofit Kit (hereinafter referred to as BLE TPMS), the driver could get the accurate tire pressure and temperature at any time through smart phone by using this kit while driving. When the system detects abnormal status, it will alarm the driver actively, and show the abnormal data and its tire location on the Multi Wheel Bluetooth TPMS APP (hereinafter referred to as APP). 2.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.
Specification Operating Voltage DC 12V/24V Operating Humidity 90％ MAX Operating Temperature -20℃ to 70℃ Storage Temperature -25℃ to 85℃ Operating Current 0.25A@12V, 0.2A@24V Sound Pressure (min.) 85dB@15cm Battery voltage detector DC 5V~32V, ±0.1V Operating Frequency 2400MHz~2483.
1. Introduction of Smart Voice TPMS Monitor 1.
1.2 Function description 1.2.1 Initial setting Display Descriptions Initial setting (Pic 1) 1. When power on, display HOME page. 2. And display battery voltage. 3. And then display warning symbol, and play welcome message. 4. Enter Monitoring mode, and receive sensors signal. 5. Sensors setup completed. The factory default for pressure unit is psi , after receiving the normal, warning symbol will disappear. (Pic2) Pic 1 Note 1: Voice Monitor and TPMS Sensor have been paired.
1.2.2 Monitoring Mode “Monitoring mode” provide 3 kind of value: Pressure, Temperature and Battery Voltage. Please press and hold the left button for 1.5 seconds to enter into “ID mode”.(1.2.3) Display Descriptions Pressure data of sensors Switch Pressure Unit : Please press the left button twice. It displays 3 kinds of pressure units, kPa, psi and bar in sequence.(Pic 3) Switch Temperature Unit : Please press the left button once.
Display Descriptions Temperature data of sensors Switch Temperature Unit : Please press the left button twice. It displays 2 kinds of temperature units, °C and °F in sequence. Switch Battery Voltage : Please press the left button once.(Pic 6) Pic 5 Pic 6 Battery Voltage Display the voltage real time. (Pic 7) Switch Pressure Unit : Please press the left button once.
1.2.3 ID mode Display each sensor ID number. Please press and hold the left button for 1.5 seconds to enter into “Settings mode” .(1.2.4) Display Descriptions Display sensor ID number Switch tire Location: Please press the left button once, the order of the tire location is front-left (FL) → front-right(Fr) → rear-left (rL) → rear-right(rr). (Pic 9) Deflation Learning new sensor ID: Please press the left button twice.
Deflation completed, display new ID number “16888”.(Pic 11) Using the same method, set up the ID number learning for tires in sequence. If learning fail, it will showing pervious ID number”12345” Pic 11 Stop learning: Please press the left button once. 1.2.4 Settings mode The product provide 3 kind of Monitored Settings : Monitored Pressure Range Settings of front tires、Monitored Pressure Range Settings of rear tires and Temperature range. Please press and hold the left button for 1.
Press the right button once to increase up 2.5kPa(0.36psi/0.1bar), and press the left button once to reduce down 2.5kPa (0.36psi/0.1bar) . (Pic 13) Minimum Tire pressure : 10-250kPa (1.436.2psi/0.1-2.5bar). Maximum tire pressure: 280-640kPa (40.692.8psi/2.8-6.4bar). Pic 13 The factory default Minimum tire pressure value is 180 kPa (26psi/1.8bar). The factory default Maximum tire pressure value is 300kPa (43psi/3bar). Using the same method, set up the other units in sequence.
Monitored Pressure Range Settings of rear tires Please press and hold the left button for 1.5 seconds. And press the left button twice, it will display upper and lower limits. (Pic.16) Press the right button once to increase up 2.5kPa(0.36psi/0.1bar), and press the left button once to reduce down 2.5kPa (0.36psi/0.1bar)(Pic 17) . Minimum Tire pressure : 10-250kPa (1.436.2psi/0.1-2.5bar). Maximum tire pressure: 280-640kPa (40.692.8psi/2.8-6.4bar). Using the same method, set up the other units in sequence.
Note : For the standard tire pressure value, please refer to the placard located at the side of the driver’s seat. Pic 19 Temperature range settings Press the left button twice and showing default range.(pic 20) Press the right button once to increase up 1 °C(1.8 °F), and press the left button once to reduce down 1 °C(1.8 °F) (Pic 21) . Tire temperature range: 60~80 °C (140~176 °F). Pic 20 The factory default Maximum Temperature value is 80°C / 176°F.
of front tires. Please press left button once when stop status. (Pic 23) Pic 23 Please press and hold left button for 1.5 sec to enter into “Monitoring mode”(1.2.2) or “Save sensor ID number and settings”(1.2.5) 1.2.5 Save sensor ID number and settings Learning new sensor ID number or change settings (Monitored Pressure Range Settings of front and rear tires, Temperature range settings), press and hold left button to exit “Setting mode” for 1.
1.2.6 Right button functions description Monitoring all tire Pressure, Temperature and Battery voltage. Display Descriptions Monitoring mode: Pressure 、 Temperature 、Battery voltage.(Pic 25) Pic 25a Mute/un-mute: Please press the right button once. Mute status, it won’t voice remind if warning occurs. You can manual unmute or wait 10 minutes for the mute function to cancel automatically. Tire status report: Please press the right button twice. And press the right button again can stop.
1.2.7 Alarms and Warnings Display Descriptions Warning of high tire pressure or low tire pressure. (Pic 27) When the system detects abnormal status, it will flash and alarm the driver actively, and show the abnormal data and its tire location on the TPMS Monitor. Pic 27 Warning of high tire temperature. (Pic 28) When the system detects abnormal status, it will flash and alarm the driver actively, and show the abnormal data and its tire location on the TPMS Monitor.
Warranty Policy Thank you for buying this product and giving us support. From the date of purchase, we provide a one-year warranty for the product, protecting the client’s interest by providing product quality assurance. During the warranty period, under normal operation and in the event of a faulty product, the company is willing to repair the faulty product or have it replaced, enabling you to get the guarantee and demonstrating the company’s responsible attitude toward products.
