Instruction Manual

ManualsBrandsSystem Sensor ManualsEquipment2100TR Photoelectronic

D200-68-00 1 I56-1144-05R

2100TR Photoelectronic Smoke

Detector with Fixed Heat

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

Specifications

Diameter: 5.5 inches (140 mm)

Height (including mounting bracket): 1.7 inches (43 mm)

Weight: 6.8 oz. (190 g)

Operating Temperature Range 32° to 100°F (0° to 38°C)

Operating Humidity Range: 10% to 93% Relative Humidity, Noncondensing

Latching Alarm: Reset by momentary power interruption

Heat Sensor: 135°F Fixed Temperature Electronic Thermistor

Electrical Ratings

System Voltage (nominal): 12 or 24 VDC

Minimum: 8.5 VDC

Maximum: 35 VDC

Maximum Ripple Voltage: 30% of nom. Voltage (peak to peak)

Standby Current: 50

A average, 100

A maximum

Alarm Ratings: 25.5 mA minimum, 100 mA maximum

(Alarm current must be limited to 100mA by the control panel. If used, the RA400Z

Remote Annunciator operates within the specified detector alarm currents.)

Reset Voltage: 1.3 VDC minimum

Reset Time: 0.3 seconds maximum

Start-up Time: 30 seconds maximum (after 60 sec. reset)

EOL Relay: A77-716B, 12/24 VDC

Remote Annunciator Output: 7 mA maximum

Auxiliary Relay Contact Ratings: 1A @ 30 VAC

Resistive Load: 1A @ 30 VDC

Special Considerations: Only one detector can be used per zone.

Figure 1. Wiring diagram for the 2100TR detector:

A78-2336-17

IMPORTANT: OBSERVE POLARITY

Polarity must be observed on the remote annunciator connections.

OPTIONAL CLASS A WIRING

EOL

–

A+

A-

RA400Z

REMOTE

ANNUNCIATOR

–

UL LISTED

COMPATIBLE

CONTROL

PANEL

INITIATING

LOOP

–

NOTE: ONLY ONE DETECTOR PER ZONE CAN BE USED.

(OPTIONAL)

RELEASING

DEVICE

COMMON

Summary of content (4 pages)

PAGE 1
INSTALLATION AND MAINTENANCE INSTRUCTIONS 2100TR Photoelectronic Smoke Detector with Fixed Heat 3825 Ohio Avenue, St. Charles, Illinois 60174 1-800-SENSOR2, FAX: 630-377-6495 Figure 1. Wiring diagram for the 2100TR detector: IMPORTANT: OBSERVE POLARITY Polarity must be observed on the remote annunciator connections.
PAGE 2
The detectors also include an output that allows optional connection of the RA400Z Remote Annunciator. Figure 2. Surface mounting of 2100TR smoke detector on 31/2-inch and 4-inch octagonal box: ;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;; Mounting Each 2100TR detector is supplied with a mounting bracket that permits the detector to be mounted: 1. To a single gang box, or 2.
PAGE 3
control panel specifications for the total loop resistance allowed for the control panel being used before wiring the detector loops. Testing NOTE: Before testing, notify the proper authorities that the smoke detector system is undergoing maintenance and will be temporarily out of service. Disable the zone or system undergoing maintenance to prevent unwanted alarms. Detectors must be tested after installation and following periodic maintenance. Test the 2100TR as follows: A. Test Switch 1.
PAGE 4
2. Vacuum the screen carefully without removing it. 3. Remove screen assembly, pulling straight out (please see Figure 5). 4. Remove the sensing chamber cover. 5. Clean the sensing chamber by vacuuming or blowing out dust and particles. 6. Replace the sensing chamber cover, aligning the arrow on the cover top with the arrow on the printed circuit board. 7. Replace the screen by placing the screen assembly over the sensing chamber cover and twisting until it snaps into place. 8.