Portier SE .... 10 GB .... 13 FR .... 16 RU ....
96 100 2 M6 (4x) K-O ø23 K-O ø29 111 PS210 816, PS215 1335 138 291 PS210 1020, PS215 1530 Portier 280
Portier Fig. A Fig. B Wire (not included) A Screw eye M6 A = min 80 mm. A+B = min 120 mm. Fig. C B Fig. D Threaded bar M6 (not included) Reset Temp. limiter To op e n Fig.
Portier Fig.
Portier Fig.
Portier Fig.
Portier Fig.
Portier Fig. J Fig. K 400V 3N~ 230V~ N L L1 L2 L3 L1 L2 L3 N L PS210E03 230V~ PS210E03 400V 3N~ 1.5 mm² PS210E06 400V 3N~ 1.5 mm² 2.5 mm² Fig. L Fig. M 230V ~ min 0.75 mm² 230V 3~ N L PS210E09 PS210E09 PS215E09 PS215E09 PS215E14 PS215E14 L1 L2 L3 N L PS210E6 230V 3~ 2.5 mm² Fig. N L1 L2 L3 400V 3N~ 230V 3~ 400V 3N~ 230V 3~ 400V 3N~ 230V 3~ 2.5 mm² 6 mm² 2.5 mm² 6 mm² 6 mm² 10 mm² Fig. O Only valid for commutable 6 - 13.
Portier Technical specifications Type Output PS210A PS215A [kW] 0 0 Airflow Sound power*1 3 [m /h] [dB(A)] 1000/1300 70 1300/2000 72 Technical specifications Type PS210E03 PS210E06 PS210E09 PS215E09 PS215E14 Output steps [kW] 1,5/3 3/6 4,5/9 4,5/9 6,7/13,5 Ambient, no heat - Portier A 1 Sound pressure*2 [dB(A)] 44/54 46/56 Voltage Amperage Length Weight [V] 230V~ 230V~ [A] 0,45 0,55 [mm] 1020 1530 [kg] 14 20 Electrical heat - Portier E 3 Airflow ∆t*3 [m3/h] 950/1200 950/1200 950/1200 12
GB Portier Assembly and operating instructions General Instructions Read these instructions carefully before installation and use. Keep this manual for future reference. The product may only be used as set out in the assembly and operating instructions. The guarantee is only valid if the product is used in the manner intended and in accordance with the instructions.
GB Portier Adjusting the unit and the airflow Direction and speed of the airflow should be adjusted according to the load on the door. Outside pressure forces the air stream to bend towards the interior of the room (when the room is heated and the outside is cold). To reduce this effect, the airflow should be directed outwards. The air director/grille is adjustable and should be angled outwards (5°-10°) to achieve the best protection of the door.
Portier Residual current circuit breaker (E) When the installation is protected by means of a residual current circuit breaker, which trips when the appliance is connected, this may be due to moisture in the heating element. When an appliance containing a heater element has not been used for a long period or stored in a damp environment, moisture can enter the element.
Tel: +46 31 336 86 00 mailbox@frico.se www.frico.net For latest updated information and information about your local contact: www.frico.se Art.no.
