Circular duct fan prio 150–250, prio silent® XP 150–315 Installation and Operating Instructions Document in original language | · 003 GB
© Copyright Systemair AB All rights reserved E&OE Systemair AB reserves the rights to alter their products without notice. This also applies to products already ordered, as long as it does not affect the previously agreed specifications.
Contents 1 2 3 4 5 6 7 8 EU Declaration of conformity..............................1 Warnings.......................................................1 Product information .........................................2 3.1 Key for item name..................................2 3.2 Intended use .........................................2 3.3 General ................................................2 3.4 Technical data .......................................3 3.4.1 Dimension ................................3 3.4.
EU Declaration of conformity | 1 EU Declaration of conformity The manufacturer: Systemair GmbH Seehöfer Straße 45 97944 Boxberg Germany Product designation: Circular duct fans Type designation: prio 150–250, prio silent® XP 150–315 Since year of manufacture: 2020 The manufacturer declares that the above mentioned products in their design and construction and the version marketed by us complies with the harmonization legislation listed below: EU directives: Regulations: 2 2006/42/EC Machinery
2 | Product information 3 Product information 3.1 Key for item name prio silent® XP = Revolution silenced V2 3.2 Intended use • The fans are intended for installation in ventilation systems. They can be installed both in duct systems and also with free suction via a suction-side contact protection grille. Free discharge via a contact protection grille is also possible. • The fan is suitable for conveying clean air.
Product information | 3.4 Technical data Max. ambient temperature [°C] see data sheet, available in our online catalogue. Max. temperature of transported air [°C] see data sheet, available in our online catalogue. Sound pressure [dB] see data sheet, available in our online catalogue. Voltage, current, frequency, enclosure class, weight see name plate of the fan The data on the name plate of the fan apply to "standard air" according to ISO 5801. 3.4.
4 | Product information 3.4.2 Wiring diagram E2 prio silent® XP 150E2, prio silent® XP 160E2, prio silent® XP 200E2, prio silent® XP 250E2, prio Silent® XP 250E2–L, prio Silent® XP 315E2–L N Neutral conductor PE Protective conductor Speed control: Voltage controllable (See accessories in our online catalogue) Motor protection: By integrated thermal contacts PE Power supply 230 V AC, 50...
Product information | Electrical connection accessories for EC version Symbol fan 10V ♦ The potentiometer must be disconnected if the fan should be controlled by other accessories via 0–10V (e.g. accessories below). 0-10V GND Controll via 0–10V signal MTP 10 S-5EC/FRQ MTP 20 S-5EC/FRQ 10V GND A EC-Basic MTV—1/10 EC-Vent EC-Vent IN/RPM optional OUT/PWM GND 3.5 TACH +10V IN/10V PWM 0...
6 | Installation 4 Installation Danger • Make sure that the mains power supply to the unit is disconnected before performing any maintenance or electrical work! • All electrical connections must be carried out by an authorized installer and in accordance with local rules and regulations. Warning • The units electrical connection to the mains power supply must be preceded by an all pole circuit breaker with a minimum 3 mm gap.
Installation | Installation options prio silent® XP 150–315 A Flap 4x Example — Rope installation B Optional key hole. Overview Details D C Y A A B B Sleeve with female thread M8 C Nut M8 Screw M8 (e.g. DIN 933) D Washer Y- Installation example “Rail” or “screws and dowels” installation on a wall or ceiling.
8 | Maintenance 4.1 Commissioning Danger • All electrical connections must be carried out by an authorized installer and in accordance with local rules and regulations. Before initial operation, check the following: • Electrical connection has been properly completed. • Protective earth has been connected. • Safety devices in place (protection grid). • Leftover installation materials and foreign materials have been removed from the casing.
Disposal | 8 Disposal ♦ Ensure material is recycled. Observe national regulations. ♦ The device and the transport packaging are predominantly made from recyclable raw materials. ♦ Disassemble the fan into its components. ♦ Separate the parts according to: • reusable material • material groups to be disposed of (metal, plastics, electrical parts, etc.
Tel.: +49 (0)7930/9272-0 Fax: +49 (0)7930/9273-92 info@systemair.de www.systemair.de Circular duct fan · Installation and Operating Instructions · · en_GB · 2021-05-03 · 003 Systemair GmbH Seehöfer Str.
