Installation, Operation and Maintenance instruction 001

ManualsBrandsSystemair ManualsFans & AccessoriesMUB/T 062 630D4 - Centrifugal box fan, 120°C continuous, insulated

Table Of Contents

1Introduction
- 1.1 Product description
- 1.2 Intended use
- 1.3 Document description
- 1.4 Product overview
  - 1.4.1 Product overview MUB/T fans and MUB/T-S fans
  - 1.4.2 Product overview MUB fans, MUB-CAV/VAV fans, and MUB/F fans
- 1.5 Name plate
  - 1.5.1 Type designation
- 1.6 Product liability
2Safety
- 2.1 Safety definitions
- 2.2 Safety instructions
- 2.3 Personal protective equipment
3Transportation and storage
4Installation
- 4.1 To do before the installation of the product
- 4.2 To install the product
5Electrical connection
- 5.1 To do before the electrical connection
- 5.2 To connect the product to the power supply
- 5.3 Speed controller for AC motors
- 5.4 To install motor protection for AC motors
- 5.5 Speed controller for EC motors
- 5.6 Motor protection for EC motors
6Commissioning
- 6.1 To do before the commissioning
- 6.2 To do the commissioning
7Operation
- 7.1 To start a product with an EC motor
- 7.2 To start a product with an AC motor
- 7.3 To stop the product
  - 7.3.1 To stop the product in an emergency
8Maintenance
- 8.1 Maintenance schedule
- 8.2 To clean the product
- 8.3 Spare parts
9Troubleshooting
10Disposal
- 10.1 To disassemble and discard the parts of the product
11Warranty
12Technical data
- 12.1 Technical data overview
- 12.2 Product dimensions
- 12.3 Wiring diagrams
13Accessory overview
- 13.1 Accessory overview MUB fans, MUB-CAV/VAV fans, MUB/T fans, MUB/T-S,MUB/T ECO and MUB+Filter fans
- 13.2 Accessory overview MUB/F fans
14EU Declaration of Conformity-Multibox
15EU Declaration of Conformity-Multibox+Filter
16EU Declaration of Conformity-Thermo fans
17EU Declaration of Conformity-Smoke extract fans
18UKCA Declaration of Conformity-Multibox
19UKCA Declaration of Conformity-MUB+Filter
20UKCADeclaration of Conformity-Thermo fans
21UKCA Declaration of Conformity-Smoke extract fans

12.2.7 Product dimensions MUB+Filter fans

Note:

If the unit of measure is not specified, the dimensions are given in millimetres.

A B C D

MUB + Filter 025 315/355 690 378 520 71

MUB + Filter 042 400/450/500 820 548 690 71

MUB + Filter 062 560/630 1020 678 820 71

MUB + Filter 100 630 1020 878 1020 71

12.3 Wiring diagrams

12.3.1 Wiring diagrams for AC fans

Refer to the wiring diagram documents that are included in the supply of the product.

The wires in the motor cables have these colours:

Wire Colour

+10 V Red

0...10 V/PWM Yellow

GND Blue

12.3.2 Wiring diagrams for EC fans

Note:

An internal potentiometer is installed on the terminal block from the factory. Remove the internal potentiometer when you use

an external speed controller for the EC fan.

Refer to the wiring diagram documents that are included in the supply of the product.